
Prototype1
domenipavec/usb-vga-computer-control
sudo apt-get install python-opencv v4l-utils python-pip sudo pip install -r python-software/requirements.txt

sudo apt-get install python-opencv v4l-utils python-pip sudo pip install -r python-software/requirements.txt
Prototype1 is an open-source printed circuit board by domenipavec, from the domenipavec/usb-vga-computer-control repository on GitHub. It is a 4-layer board of 57.5 × 92 mm with 147 parts on 125 nets, routed with 1,513 tracks and 261 vias.
It is built around the ATTINY841-SSU, TVP7002PZP and USBLC6-2SC6, with the 24LC16B/P, LD1117S12TR-HXY and LD1117S33TR(MS) among its other parts. Its parts include 68 capacitors, 47 resistors, 11 ICs, 4 connectors and 4 inductors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
sudo apt-get install python-opencv v4l-utils python-pip
sudo pip install -r python-software/requirements.txt
| Qty | Value | Footprint | References |
|---|---|---|---|
| 42 | 100nF | Capacitors_SMD:C_0402 | C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C27, C28, C29 +26 |
| 23 | 22R | Resistors_SMD:R_0402 | R35, R36, R37, R38, R39, R40, R41, R42, R43, R44, R45, R46, R47, R48, R49, R50 +7 |
| 7 | 10nF | Capacitors_SMD:C_0402 | C4, C5, C6, C7, C9, C10, C12 |
| 6 | 10k | Resistors_SMD:R_0805 | R4, R5, R12, R25, R30, R32 |
| 6 | 10uF | Capacitors_SMD:C_0805 | C62, C63, C64, C65, C66, C67 |
| 4 | 1nF | Capacitors_SMD:C_0402 | C1, C2, C3, C34 |
| 4 | Ferrite_Bead | Resistors_SMD:R_0805 | L1, L2, L3, L4 |
| 3 | 330R | Resistors_SMD:R_0805 | R11, R76, R78 |
| 3 | 75R | Resistors_SMD:R_0805 | R6, R7, R8 |
| 3 | TEST_1P | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W1, W2, W4 |
| 2 | 13pF | Capacitors_SMD:C_0805 | C42, C43 |
| 2 | 1k5 | Resistors_SMD:R_0805 | R1, R15 |
| 2 | 1uF | Capacitors_SMD:C_0805 | C60, C61 |
| 2 | 22pF | Capacitors_SMD:C_0805 | C38, C39 |
| 2 | 22uF | Capacitors_SMD:C_1206 | C26, C30 |
| 2 | 2k2 | Resistors_SMD:R_0805 | R73, R74 |
| 2 | 47k | Resistors_SMD:R_0805 | R2, R3 |
| 2 | 68R | Resistors_SMD:R_0805 | R13, R14 |
| 2 | NUP2105L | drt:DRT | D2, D3 |
| 2 | USBLC6-2SC6 | TO_SOT_Packages_SMD:SOT-23-6 | U2, U8 |
| 1 | 120R | Resistors_SMD:R_0805 | R77 |
| 1 | 180R | Resistors_SMD:R_0805 | R75 |
| 1 | 200R | Resistors_SMD:R_0402 | R9 |
| 1 | 24LC16 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U4 |
| 1 | 4.7nF | Capacitors_SMD:C_0805 | C11 |
| 1 | 6.04k | Resistors_SMD:R_0402 | R10 |
| 1 | ATTINY841-SSU | SMD_Packages:SOIC-14_N | IC1 |
| 1 | CONN_01X02 | Socket_Strips:Socket_Strip_Straight_1x02 | P4 |
| 1 | CONN_01X06 | attiny841-spi:ATTINY841-SPI | P2 |
| 1 | CYUSB301X-121bga | bga121:BGA_121 | U3 |
| 1 | Crystal-12Mhz | Crystals:Crystal_HC49-U_Vertical | Y1 |
| 1 | Crystal-19.2Mhz | Crystals:Crystal_HC49-U_Vertical | Y2 |
| 1 | LD1117S12TR | TO_SOT_Packages_SMD:SOT-223 | U11 |
| 1 | LD1117S18TR | TO_SOT_Packages_SMD:SOT-223 | U10 |
| 1 | LD1117S33TR | TO_SOT_Packages_SMD:SOT-223 | U9 |
| 1 | LED | LEDs:LED-3MM | D1 |
| 1 | NCP360SNT1G | TO_SOT_Packages_SMD:SOT-23-5 | U6 |
| 1 | SW_Push | pushbutton:pushbutton | SW1 |
| 1 | TVP7002 | Housings_QFP:LQFP-100_14x14mm_Pitch0.5mm | U1 |
| 1 | USB3_TYPEB | usb3-typeb:USB3_TYPE_B | U5 |
| 1 | USB_B | Connectors:USB_B | P1 |
| 1 | VGA | vga:VGA | J1 |
The 143 most common of 147 parts.

domenipavec/usb-vga-computer-control
sudo apt-get install python-opencv v4l-utils python-pip sudo pip install -r python-software/requirements.txt

ekundo/combolite
ComboLite: плата расширения для «Вектора-06Ц» — квазидиски, IDE, дисковод, AY, VGA, Wi-Fi

kasamikona/HeikouBox
A project towards running "Parallelogram" demo by lft (Linus Åkesson).


ale-giustina/CAN-serializer
A 3 interface FDCAN serializer based on a STM32G473CCTx

gschuurman/android_vendor_gschuurman_vehicle_interfaces
vehicle interfaces for android automotive for a custom headunit


marqs85/de2-vd
Video digitizer add-on module for DE2-115 FPGA development board.

vgacentrifuge/pcb
The repository for designing the PCB for the VGA-mixer in TDT4295
It measures 57.5 × 92 mm and has 4 copper layers, 1.6 mm thick.
147 parts, built around the ATTINY841-SSU, TVP7002PZP, USBLC6-2SC6 and 24LC16B/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the domenipavec/usb-vga-computer-control repository on GitHub, at the commit this page was made from: the board is kicad/prototypes/2/prototype1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask domenipavec before reusing the design.