

KiCAD board files for making an interface board that converts the RJ45 diagnostic port on most newer GE appliances to usable UART. Note: these are untested designs.
- Size
- 88.9 × 71.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 44
- Nets
- 32
- Pads
- 162
- Tracks, vias
- 306, 96
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 18 Feb 2020
- Updated
- 18 Feb 2020
Overview
Adapter is an open-source printed circuit board by doitaljosh, from the doitaljosh/gea-interface-board repository on GitHub. It is a 2-layer board of 88.9 × 71.8 mm with 44 parts on 32 nets, routed with 306 tracks and 96 vias.
It is built around the 74LVC1GU04DRL, AMS1117-5.0 and BAV99, with the DTA143XCA among its other parts. Its parts include 14 resistors, 10 diodes, 8 capacitors, 3 ICs and 3 connectors. It belongs with the interfaces and adapters boards of this library.
Main components
474LVC1GU04DRL
-- Logic Gates ROHSTexas InstrumentsLogic GatesAMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBAV99
SOT-231 Pair Series Connection 1.25V@150mA 100V 215mA 250mW 4A 4ns 500nA@80V SOT-23 Switching Diodes ROHSNexperiaSwitching DiodesDTA143XCA
SOT-23-55℃~+150℃ 1 PNP Pre-Biased 100mA 2.5V@20mA,0.3V 2.6 200mW 250MHz 30 300mV 300mV@0.1mA,5V 300mV@10mA,0.5mA 6.11kΩ PNP SOT-23 Digital Transistors ROHSJiangsu Changjing Electronics Technology (CJ)Digital Transistors
README
README.mdKiCAD Board Files for an open source adapter that allows hacking and protyping with GE appliances.
Note: these haven't been tested or produced.
They are based off of GE's official implementation. I've reverse engineered an interface on an oven board, and this is essentially a half-duplex to full-duplex UART converter. It can talk to two appliances at once, as it has two channels. A smaller, single channel variant is in the works.
RJ45 port pinout:
- GND
- GEA_E (half-duplex 19200 baud)
- 9-14VDC
- GEA2_RXD (full-duplex 230400 baud)
- GEA2_TXD
- 5V
- NC
- NC
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1u | Capacitor_Tantalum_SMD:CP_EIA-1608-10_AVX-L | C101, C102, C103, C104, C201, C202, C203, C204 |
| 8 | 330 | Resistor_SMD:R_0603_1608Metric | R104, R105, R106, R107, R204, R205, R206, R207 |
| 8 | LED | LED_SMD:LED_0603_1608Metric | D102, D103, D104, D105, D202, D203, D204, D205 |
| 4 | MountingHole_3.5mm_Pad_Via | MountingHole:MountingHole_3.5mm_Pad_Via | H1, H2, H3, H4 |
| 2 | 120 | Resistor_SMD:R_0603_1608Metric | R102, R202 |
| 2 | 22k | Resistor_SMD:R_0603_1608Metric | R103, R203 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric | R101, R201 |
| 2 | 74LVC1GU04DRL | Package_TO_SOT_SMD:SOT-553 | U101, U201 |
| 2 | BAV99 | Package_TO_SOT_SMD:SOT-23 | D101, D201 |
| 2 | DTA143X | Package_TO_SOT_SMD:SOT-323_SC-70 | Q101, Q201 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1201 |
| 1 | GEABus IN CH1 | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J101 |
| 1 | GEABus IN CH2 | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J201 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J1201 |
Similar boards
- 6 layers73 × 100 mm

- 4 layers99 × 93 mm

Piezo driver
cyntem/piezo_driver_stm32
3-axis PCB and schematics High Voltage Piezo actuator driver with 2 Step motor driver and optional blue-ray microscope (just for test)
280 parts - 2 layers153.6 × 50 mm

- 2 layers29.2 × 101.6 mm

- 2 layers10.8 × 21.8 mm

NullCIC
Redherring32/NullCIC
A little board to replace the CIC on the original NES or OpenTendo.
4 parts116 - 4 layers233.4 × 100 mm

- 4 layers100 × 70 mm

- 2 layers114.2 × 36.8 mm

Airbox
Alacrity-Education/AirBoxV2
The AirBox V2 Station is an open source air quality monitoring station based on the Sensirion SEN66 sensor. It measures particulate matter, CO2, VOC and NOx, runs on a solar charged lithium cell, and reports over Wi-Fi.
68 parts6GPL-3.0
Questions
How big is the Adapter PCB?
It measures 88.9 × 71.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Adapter use?
44 parts, built around the 74LVC1GU04DRL, AMS1117-5.0, BAV99 and DTA143XCA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Adapter KiCad files?
From the doitaljosh/gea-interface-board repository on GitHub, at the commit this page was made from: the board is adapter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Adapter design in my own project?
Its repository states no licence, so its author keeps all rights: ask doitaljosh before reusing the design.