

Paper badges
- Size
- 99.6 × 57.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 68
- Nets
- 70
- Pads
- 238
- Tracks, vias
- 416, 39
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 6 Jun 2016
- Updated
- 9 Jan 2017
Overview
Paper badges is an open-source printed circuit board by dodgymike, from the dodgymike/bsidescpt2016badge repository on GitHub. It is a 2-layer board of 99.6 × 57.9 mm with 68 parts on 70 nets, routed with 416 tracks and 39 vias.
It is built around the ESP-12E, 74HC595 and 74LS165PC, with the MC78L05ACH, MCP73831 and TSOP38238 among its other parts. Its parts include 22 resistors, 11 capacitors, 7 ICs, 7 diodes and 2 connectors. It belongs with the lEDs and displays boards and the ESP8266 boards of this library.
Main components
6ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi Modules74HC595
SOP-16-40℃~+85℃ 1 100ns@5V,50pF 10MHz 2V~6V 74HC 8 Serial-to-Serial or Parallel Tri-State SOP-16 Shift Registers ROHSGRShift Registers74LS165PC
DIP-160.4mA 0℃~+70℃ 105mW 35MHz 4.75V~5.25V 47ns@5V,50pF 8 8mA Asynchronous parallel load function Complementary Parallel-to-Serial DIP-16 Shift RegistersTexas InstrumentsShift RegistersMC78L05ACH
SOT-890℃~+125℃@(Tj) 1 1.7V@(40mA) 100mA 3.8mA 30V 40uV 49dB@(120Hz) 5V Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable、Short Circuit Protection SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMCP73831
UncategorisedMicrochip TechnologyTSOP38238
SIP-3-2.54mm-25℃~+85℃ 10mW 2.5V~5.5V 350uA 38kHz 45m ±45° SIP-3-2.54mm Infrared Remote Receiver (IRM) ROHSVishay IntertechnologyInfrared Remote Receiver (IRM)
README
README.mdbsidescpt2016badge
Repo for server code + board designs
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | SW_PUSH | Buttons_Switches_SMD:SW_SPST_B3S-1000 | BUTTON_L1, BUTTON_L2, BUTTON_L3, BUTTON_L4, BUTTON_L5, BUTTON_L6, BUTTON_L7, BUTTON_L8, PROGRAM1, RESET1 |
| 9 | 100 | Resistors_SMD:R_0805_HandSoldering | R1, R2, R3, R4, R5, R6, R7, R9, R10 |
| 8 | 100 Ohm | Resistors_SMD:R_0805_HandSoldering | R8, R11, R12, R13, R16, R17, R18, R19 |
| 6 | LED | LEDs:LED_0805 | D2, D3, L2, L3, L4, Power1 |
| 3 | 1uF | Capacitors_SMD:C_0805_HandSoldering | C2, C3, C11 |
| 3 | LEDs:LED-5MM | LEDs:LED_0805 | Infrared1, L1, L5 |
| 2 | 10k Ohm | Resistors_SMD:R_0805_HandSoldering | R14, R15 |
| 2 | 10uF | Capacitors_SMD:C_0805_HandSoldering | C1, C10 |
| 2 | 4.7 uF | Capacitors_SMD:C_0805_HandSoldering | C8, C9 |
| 2 | 470 Ohm | Resistors_SMD:R_0805_HandSoldering | R20, R22 |
| 2 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02 | Power2, Program1 |
| 1 | 0.1 uF | Capacitors_SMD:C_0805_HandSoldering | C6 |
| 1 | 1 uF | Capacitors_SMD:C_0805_HandSoldering | C7 |
| 1 | 100 Ohm THERMISTOR | Resistors_SMD:R_0805_HandSoldering | TH1 |
| 1 | 12 MHz Crystal | Crystals:Crystal_SMD_5032_2Pads | Y1 |
| 1 | 22 pF | Capacitors_SMD:C_0805_HandSoldering | C4 |
| 1 | 22pF | Capacitors_SMD:C_0805_HandSoldering | C5 |
| 1 | 4k Ohm | Resistors_SMD:R_0805_HandSoldering | R21 |
| 1 | 74HC595 | Housings_SSOP:TSSOP-16_4.4x5mm_Pitch0.65mm | U3 |
| 1 | 74LS165 | Housings_SSOP:TSSOP-16_4.4x5mm_Pitch0.65mm | U5 |
| 1 | CH340H/T | OLIMEX_IC-FP:SSOP-20W | U6 |
| 1 | CONN_01X04 | Pin_Headers:Pin_Header_Straight_1x04 | P2 |
| 1 | ESP-12E | ESP8266:ESP-12E | U1 |
| 1 | Led_RGB_CA | Pin_Headers:Pin_Header_Straight_1x04 | D1 |
| 1 | MC78L05ACH | custom-footprints:MC78L05ACH-SOT89-3_Housing_Handsoldering | U4 |
| 1 | MCP73831 | TO_SOT_Packages_SMD:SOT-23-5 | U7 |
| 1 | TSOP38238 | custom-footprints:IR_Receiver | U2 |
| 1 | USB_OTG | Connect:USB_Micro-B | P1 |
The 66 most common of 68 parts.
More from dodgymike/bsidescpt2016badge
5- 2 layers

- 2 layers

- 2 layers

- 2 layers

- 2 layers

Similar boards
- 2 layers14.6 × 13.1 mm

- 2 layers421 × 60 mm

- 4 layers99.7 × 99.7 mm

- 4 layers120 × 125 mm

- 2 layers

Panel old
dankar/altair8800
What started as a Intel 8080 emulator turned into a Altair 8800 emulator with associated hardware for a front panel.
103 parts31MIT - 2 layers85.1 × 31.8 mm

Esp01Expander
ruenahcmohr/esp_01Expand32
esp-01 (esp8266) IO expander, 16 output, 16 input = 32
20 parts15 - 2 layers150 × 150 mm

- 2 layers138 × 115 mm

Polymod proto 1
mattybrad/polymod4
A polyphonic digital synthesizer which can be patched like an analog modular synth.
133 parts2GPL-3.0
Questions
How big is the Paper badges PCB?
It measures 99.6 × 57.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Paper badges use?
68 parts, built around the ESP-12E, 74HC595, 74LS165PC and MC78L05ACH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Paper badges KiCad files?
From the dodgymike/bsidescpt2016badge repository on GitHub, at the commit this page was made from: the board is badge-dc24/paper-badges.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Paper badges design in my own project?
Its repository states no licence, so its author keeps all rights: ask dodgymike before reusing the design.