2 layers100 × 71 mm
Armed
ed-ni/Armed
Arduino compatbile using the Arduino Core STM32 and working with the Marlin 2.0 3D printer firmware.
210 parts
2 layers100 × 95 mm
Controller
Doc-Raptor/dragon_controller332bit 3d-printer controller board for 3d printers from china with the anet-stlye controller-board
- Size
- 100 × 95 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 88
- Nets
- 103
- Pads
- 371
- Tracks, vias
- 1,639, 79
- Pours
- 24
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Feb 2020
- Updated
- 25 May 2020
Overview
Controller is an open-source printed circuit board by Doc-Raptor, from the Doc-Raptor/dragon_controller repository on GitHub. It is a 2-layer board of 100 × 95 mm with 88 parts on 103 nets, routed with 1,639 tracks and 79 vias.
It is built around the MP2451DJ, RT9013-33GB and B140-13-F(MS), with the HUF76639S3ST, HY4903B and PMV40UN2 among its other parts. Its parts include 30 connectors, 23 capacitors, 12 resistors, 4 diodes and 3 ICs. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
6
MP2451DJ
TSOT-23-6-40℃~+125℃ 1 130uA 2MHz 3.3V~36V Adjustable Buck Buck Built-in TSOT-23-6 DC-DC Converters ROHSMonolithic Power SystemsDC-DC Converters
RT9013-33GB
SOT-23-5-40℃~+125℃@(Tj) 1 25uA 3.3V 30uVrms 400mV@(500mA) 5.5V 500mA 50dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRICHTEKVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
B140-13-F(MS)
SMASchottky DiodesMSKSEMI
HUF76639S3ST
TO-263-2-55℃~+175℃ 1 N-channel 100V 140pF 180W 2.4nF 28mΩ@4.5V 3V 50A 520pF 86nC@10V N-Channel ±16V TO-263-2 MOSFETs ROHSonsemiMOSFETs
HY4903B
TO-263-2L1 N-channel 1.236nF 11.506nF 214W 290A 30V 3V 3mΩ@4.5V 762pF N-Channel TO-263-2L MOSFETs ROHSHUAYIMOSFETs
PMV40UN2
SOT23-330V, 4.4A, N-Channel Trench MOSFETNexperiaUncategorised
README
README.mdThis is a controller-board for 3d printers from china which are based on the anet printers and using an 8-bit board with on-board stepper driver and sometimes no fuse-protection (and no thermal-run-away). This board is a low cost replacement with an stm32f103ret and socketed stepper drivers. It is also capable of runnung from 24v.
Parts
88| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_1206_3216Metric | C1, C6, C7, C8, C9, C10, C13, C18 |
| 4 | 100uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C20, C22, C24, C26 |
| 4 | 10uF | Capacitor_SMD:C_1206_3216Metric | C11, C15, C16, C19 |
| 4 | 4K7 | Resistor_SMD:R_1206_3216Metric | R12, R18, R21, R22 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | Pololu_Breakout_A4988 | Module:Pololu_Breakout-16_15.2x20.3mm | A1, A2, A3, A4 |
| 3 | 1N5819 | Diode_SMD:D_SOD-123 | D2, D8, D11 |
| 3 | 1uF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C12 |
| 2 | 100 | Resistor_SMD:R_1206_3216Metric | R11, R17 |
| 2 | 10K | Resistor_SMD:R_1206_3216Metric | R3, R7 |
| 2 | 20pF | Capacitor_SMD:C_0603_1608Metric | C14, C17 |
| 2 | z-Stepper | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J9, J44 |
| 1 | 100K | Resistor_SMD:R_1206_3216Metric | R5 |
| 1 | 124K | Resistor_SMD:R_1206_3216Metric | R1 |
| 1 | 1K | Resistor_SMD:R_1206_3216Metric | R2 |
| 1 | 23K7 | Resistor_SMD:R_1206_3216Metric | R4 |
| 1 | 3.3V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J46 |
| 1 | 33pF | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | 4.7uH | Inductor_SMD:L_1812_4532Metric | L1 |
| 1 | 5V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J45 |
| 1 | B140-13-F | Diode_SMD:D_SMA | D1 |
| 1 | BOOT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J12 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | EXP1 | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J29 |
| 1 | EXP2 | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J30 |
| 1 | EXP3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J14 |
| 1 | F_Heatbed_15A | Fuse:Fuseholder_Blade_ATO_Littelfuse_Pudenz_2_Pin | F2 |
| 1 | Fan_Cooler | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | Fuse_Power | Fuse:Fuseholder_Blade_ATO_Littelfuse_Pudenz_2_Pin | F1 |
| 1 | HUF76639S3ST | Package_TO_SOT_SMD:TO-263-3_TabPin2 | Q3 |
| 1 | HY4903B | Package_TO_SOT_SMD:TO-263-3_TabPin2 | Q1 |
| 1 | Hotend | Connector_Phoenix_MC_HighVoltage:PhoenixContact_MCV_1,5_2-G-5.08_1x02_P5.08mm_Vertical | J5 |
| 1 | J_E0 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J50 |
| 1 | J_X | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J51 |
| 1 | J_Y | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J52 |
| 1 | J_Z | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J49 |
| 1 | MAX_END | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J16 |
| 1 | MP2451 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | PMV40UN2 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | Power_Heat | Connector_Phoenix_GMSTB:PhoenixContact_GMSTBVA_2,5_2-G-7,62_1x02_P7.62mm_Vertical | J10 |
| 1 | Power_IN | Connector_Phoenix_GMSTB:PhoenixContact_GMSTBVA_2,5_2-G-7,62_1x02_P7.62mm_Vertical | J3 |
| 1 | RT9013-33GB | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | SD_CARD | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J28 |
| 1 | SPI | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | STM32F103RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | SV1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | Serial | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J31 |
| 1 | TH_B | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | TH_E | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | VCC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J43 |
| 1 | X- | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J17 |
| 1 | Y- | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J15 |
| 1 | Z- | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J13 |
| 1 | e0-Stepper | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J60 |
| 1 | x-Stepper | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J33 |
| 1 | y-Stepper | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J39 |
Questions
How big is the Controller PCB?
It measures 100 × 95 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Controller use?
88 parts, built around the MP2451DJ, RT9013-33GB, B140-13-F(MS) and HUF76639S3ST. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Controller KiCad files?
From the Doc-Raptor/dragon_controller repository on GitHub, at the commit this page was made from: the board is controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask Doc-Raptor before reusing the design.
Similar boards
- 2 layers130 × 110 mm
3D Printer Mainboard STM32
m47812/Custom-3D-Printer-Controller
A fully custom 3D Printer controller board based on an stm32f7 controller with TMC2209 stepper drivers
191 parts10GPL-3.0 - 2 layers
Afork kicad parts
CapnKernel/afork-kicad-parts
A collection of symbols and footprints that I know to work well in KiCad
13 parts - 2 layers32 × 96 mm
- 2 layers40 × 70 mm
- 2 layers50 × 44 mm
Baseboard
xtompok/home_automation_switchboard
Board fitting into wall switch, support for 1Wire, quadrature encoder, and much more. RS-485
82 partsMIT - 2 layers49 × 59 mm
- 4 layers120 × 113 mm
Voron Klipper Board
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group
360 parts1.1kGPL-3.0