

Riscduino Fpga Rev1.0
Riscduino PCB Board documentation
- Size
- 104.3 × 63.6 mm
- Copper layers
- 2
- Thickness
- 1.62 mm
- Parts
- 96
- Nets
- 85
- Pads
- 393
- Tracks, vias
- 1,296, 84
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 25 Jul 2023
- Updated
- 15 Mar 2024
Overview
Riscduino Fpga Rev1.0 is an open-source printed circuit board by dineshannayya, from the dineshannayya/riscduino_board repository on GitHub. It is a 2-layer board of 104.3 × 63.6 mm with 96 parts on 85 nets, routed with 1,296 tracks and 84 vias.
It is built around the CH340C, W25Q32JVSSIQ and 23LC1024-I/P, with the LM1117MP-3.3 and ASE-10.000MHZ-LC-T among its other parts. Its parts include 35 resistors, 21 connectors, 19 capacitors, 8 switches and 6 diodes. It belongs with the fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
Main components
5CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersW25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH23LC1024-I/P
PDIP-8-40℃~+85℃ 10mA 1Mbit 2.5V~5.5V 4uA SPI PDIP-8 SRAM ROHSMicrochip TechnologySRAMLM1117MP-3.3
SOT-2230℃~+125℃@(Ta) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA 99uVrms Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsASE-10.000MHZ-LC-T
SMD3225-4P-40℃~+85℃ 10MHz 3.3V 7mA CMOS ±50ppm SMD3225-4P Crystal Oscillators ROHSAbraconCrystal Oscillators
README
README.mdriscduino_board
Riscduino PCB Board documentation
Parts
96| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 10K | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R6, R12, R16, R19, R20, R21, R22, R23, R24, R25, R31, R32, R33, R36 +2 |
| 10 | 0.1uF | Riscduino.Library:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C5, C7, C8, C14, C15, C18, C24 |
| 7 | 4Pin Round Button SPST Straight Tactile Switch SMD - TS4550TP | Riscduino.Library:SW_SPST_EVPBF_TS4550TP | SW1, SW3, SW4, SW5, SW6, SW7, SW8 |
| 6 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C10, C12, C16, C17, C23 |
| 6 | 470 Ohm | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R14, R15, R28, R29, R30 |
| 4 | 0E | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R3, R11, R26 |
| 4 | BLUE LED | Riscduino.Library:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3, D5, D6, locked |
| 3 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J4, J8, J13 |
| 3 | Conn_01x08_Female_Header | Riscduino.Library:PinHeader_1x08_P2.54mm_Vertical | J3, J7, J10 |
| 2 | 0E | Riscduino:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R18, R27 |
| 2 | 10uF | Riscduino.Library:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11, C13 |
| 2 | Conn_01x03_Male_Header | Riscduino.Library:PinHeader_1x03_P2.54mm_Vertical | J2, J12 |
| 2 | Conn_01x08_Male_Header | Riscduino.Library:PinHeader_1x08_P2.54mm_Vertical | J16, J17 |
| 2 | Conn_02x15_Male_Header | Connector_PinHeader_2.54mm:PinHeader_2x15_P2.54mm_Vertical | J5, J18 |
| 2 | DNI | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R34, R35 |
| 2 | GREEN LED | Riscduino.Library:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D4 |
| 2 | USB_B_Micro_Female | Riscduino.Library:USB_Micro-B_Molex-105017-0001 | J9, J21 |
| 1 | 100E | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17 |
| 1 | 22uF | Riscduino.Library:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 23LC1024-I/P | Riscduino.Library:DIP-8_W7.62mm_LongPads | U3 |
| 1 | APX811-29UG-7 | Package_TO_SOT_SMD:SOT-143_Handsoldering | U1 |
| 1 | ASE-10.000MHZ-LC-T | Riscduino.Library:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | X1 |
| 1 | CH340C | Riscduino.Library:SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 1 | Conn_01x06_Female_Header | Riscduino.Library:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Conn_01x06_Male_Header | Riscduino.Library:PinHeader_1x06_P2.54mm_Vertical | J14 |
| 1 | Conn_01x10_Female_Header | Riscduino.Library:PinHeader_1x10_P2.54mm_Vertical | J11 |
| 1 | Conn_01x10_Male_Header | Riscduino.Library:PinHeader_1x10_P2.54mm_Vertical | J15 |
| 1 | Conn_02x04_Male_Header | Riscduino.Library:PinHeader_2x04_P2.54mm_Vertical | J6 |
| 1 | Conn_02x04_Male_Header | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J19 |
| 1 | DNI | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | DNI-0E | Riscduino.Library:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | LM1117MP-3.3 | Riscduino.Library:SOT-223-3_TabPin2 | U6 |
| 1 | MountingHole | Riscduino.Library:Arduino_UNO_R3_WithMountingHoles | H1 |
| 1 | SW_DIP_x04 | Package_DIP:DIP-8_W7.62mm | SW2 |
| 1 | USB Type A Female | Connector_USB:USB_A_Molex_67643_Horizontal | J20 |
| 1 | W25Q32JVSS | Riscduino.Library:SOIC-8_5.23x5.23mm_P1.27mm | U8 |
More from dineshannayya/riscduino_board
2- 2 layers81.7 × 63.6 mm

- 2 layers88.6 × 27.6 mm

Riscduino ATMEGA Adpater Rev1.0
dineshannayya/riscduino_board
Riscduino PCB Board documentation
71 parts2
Similar boards
- 2 layers70.6 × 53.7 mm

Riscduino Uno
dineshannayya/riscduino_bringup
Host all the MPW Bring-up related Enviornment
95 parts2Apache-2.0 - 4 layers100 × 100 mm

Pmic test board
efabless/foss-asic-tools
FOSS-ASIC-TOOLS is all in one container for SKY130 based design both Analog and Digital. Below is a list of the current tools already installed and ready to use.
205 parts121Apache-2.0 - 4 layers140 × 95 mm

- 2 layers50.8 × 48.3 mm

- 2 layers55.9 × 88.9 mm

Delay pedal
barlasardic/nano-delay-pedal
A delay pedal for electric guitars using arduino nano.
61 partsMIT - 2 layers

- 2 layers291.8 × 265.6 mm

Laser driver v3
scular-HCC/DualLaserPDHDriver
Dual laster Pound-Dreaver-Hall driver setup. 1550 nm DFBs. Q=10^-5. Less than 20 GHz difference
198 parts - 4 layers77.3 × 48.5 mm

ESP32 IOT
WasikeIsaac/ESP32_IOT-PCB-
ESP32 IoT board: 4-layer KiCad PCB with USB-C, BME280, mic, audio amp, SD card, GPIO breakout. Full custom design from schematic to layout.
87 parts1
Questions
How big is the Riscduino Fpga Rev1.0 PCB?
It measures 104.3 × 63.6 mm and has 2 copper layers, 1.62 mm thick.
What parts does the Riscduino Fpga Rev1.0 use?
96 parts, built around the CH340C, W25Q32JVSSIQ, 23LC1024-I/P and LM1117MP-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Riscduino Fpga Rev1.0 KiCad files?
From the dineshannayya/riscduino_board repository on GitHub, at the commit this page was made from: the board is KiCad_PCB/Riscduino_Fpga_Rev1.0/Riscduino_Fpga_Rev1.0.kicad_pcb and its schematic KiCad_PCB/Riscduino_ATMEGA_Adpater_Rev1.0/Riscduino_ATMEGA_Adpater_Rev1.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Riscduino Fpga Rev1.0 design in my own project?
Its repository states no licence, so its author keeps all rights: ask dineshannayya before reusing the design.