2 layers100.2 × 68.6 mm
Board MKIV
Demetrius-Ross/SimMonitor
Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
45 parts
2 layers100 × 32 mm
ESP Board
Demetrius-Ross/SimMonitorRename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
- Size
- 100 × 32 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 19
- Nets
- 47
- Pads
- 113
- Tracks, vias
- 262, 15
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 Dec 2024
- Updated
- 7 Aug 2026
Overview
ESP Board is an open-source printed circuit board by Demetrius-Ross, from the Demetrius-Ross/SimMonitor repository on GitHub. It is a 2-layer board of 100 × 32 mm with 19 parts on 47 nets, routed with 262 tracks and 15 vias.
It is built around the REC5A-2405SW/H2/X1, SH-7070TB and CR1206-FX-1002ELF, with the UHE2A470MPD, COM-16347 and CRL1206-FW-R330ELF among its other parts. Its parts include 5 resistors, 3 capacitors, 2 ICs, 2 diodes and 2 switches. It belongs with the ESP32 boards of this library.
Main components
9
REC5A-2405SW/H2/X1
DIP,31.8x20.3mm1 18V~36V 1A 2kV 5V 5W 81% DIP,31.8x20.3mm Isolated Power Modules ROHSRECOM PowerIsolated Power ModulesSH-7070TB
SMD-40℃~+85℃ 100mA 16 Absolute type Vertical welding SMD Rotary Coding Switch ROHSNidecRotary Encoders
CR1206-FX-1002ELF
1206-55℃~+155℃ 10kΩ 200V 250mW Thick Film Resistor ±1% ±100ppm/℃ 1206 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface MountUHE2A470MPD
插件,D10xL12.5mm-40℃~+105℃ 100V 10mm 12.5mm 47uF ±20% 插件,D10xL12.5mm Aluminum Electrolytic Capacitors - Leaded ROHSNichiconAluminum Electrolytic Capacitors - Leaded
COM-16347
5050内置上电复位电路、内置掉电复位电路、集成智能反向连接保护功能、内置单向传输功能 5050 RGB LEDs(Built-in IC) ROHSSparkFun ElectronicsUncategorisedCRL1206-FW-R330ELF
1206-55℃~+125℃ 250mW 330mΩ Thick Film Resistor ±1% ±200ppm/℃ 1206 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface MountDS01C-254-S-03BE
-- DIP Switches ROHSCUIDIP SwitchesPB400EEQR1BLK
-- Push Button Switch ROHSE-SwitchPushbutton Switches
SS34B-HF
DO-214AA(SMB)-55℃~+150℃ 1 Independent 3A 40V 500uA@40V 550mV@3A 80A DO-214AA(SMB) Schottky Diodes ROHSComchipSchottky Diodes
README
README.mdSimMonitoring Overview WIP
Rename the main script to main.py '''bash mv espnow_sender_relay.py main.py '''
Flash it to the ESP32: '''bash mpremote connect /dev/ttyUSB0 fs cp main.py : '''
Reset the ESP32 to run it automatically: '''bash mpremote connect /dev/ttyUSB0 reset '''
If you want manual execution, you can run any script interactively: '''bash mpremote connect /dev/ttyUSB0 run gpio_test.py '''
Wiring Guide for Each ESP32 Device
ESP32 Device ID Configuration for Sender
Below is a quick reference for how to wire GPIO17, GPIO16, GPIO4, and GPIO2 to assign a device ID (0–15). Each pin is interpreted as a bit in the 4-bit ID, read in the order (Pin2=bit0, Pin4=bit1, Pin16=bit2, Pin17=bit3).
| Device ID | Binary (bit3..bit0) | Pin17 (bit3) | Pin16 (bit2) | Pin4 (bit1) | Pin2 (bit0) |
|---|---|---|---|---|---|
| 0 | 0000 | 0 (LOW) | 0 (LOW) | 0 (LOW) | 0 (LOW) |
| 1 | 0001 | 0 (LOW) | 0 (LOW) | 0 (LOW) | 1 (HIGH) |
| 2 | 0010 | 0 (LOW) | 0 (LOW) | 1 (HIGH) | 0 (LOW) |
| 3 | 0011 | 0 (LOW) | 0 (LOW) | 1 (HIGH) | 1 (HIGH) |
| 4 | 0100 | 0 (LOW) | 1 (HIGH) | 0 (LOW) | 0 (LOW) |
| 5 | 0101 | 0 (LOW) | 1 (HIGH) | 0 (LOW) | 1 (HIGH) |
| 6 | 0110 | 0 (LOW) | 1 (HIGH) | 1 (HIGH) | 0 (LOW) |
| 7 | 0111 | 0 (LOW) | 1 (HIGH) | 1 (HIGH) | 1 (HIGH) |
| 8 | 1000 | 1 (HIGH) | 0 (LOW) | 0 (LOW) | 0 (LOW) |
| 9 | 1001 | 1 (HIGH) | 0 (LOW) | 0 (LOW) | 1 (HIGH) |
| 10 | 1010 | 1 (HIGH) | 0 (LOW) | 1 (HIGH) | 0 (LOW) |
| 11 | 1011 | 1 (HIGH) | 0 (LOW) | 1 (HIGH) | 1 (HIGH) |
| 12 | 1100 | 1 (HIGH) | 1 (HIGH) | 0 (LOW) | 0 (LOW) |
| 13 | 1101 | 1 (HIGH) | 1 (HIGH) | 0 (LOW) | 1 (HIGH) |
| 14 | 1110 | 1 (HIGH) | 1 (HIGH) | 1 (HIGH) | 0 (LOW) |
| 15 | 1111 | 1 (HIGH) | 1 (HIGH) | 1 (HIGH) | 1 (HIGH) |
Notes
- GPIO2 is the least significant bit (bit0).
- GPIO17 is the most significant bit (bit3).
- Use 10kΩ resistors (or internal pulls) to pull each pin HIGH or LOW.
- For a Sender role, set GPIO18 = 0 (LOW) and GPIO19 = 0 (LOW). This yields
role_value = 0=>"SENDER".
Parts
19| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | CR1206-FX-1002ELF | footprints:RESC3216X75N | R13, R14, R15, R16 |
| 2 | UHE2A470MPD | footprints:PCAP_10x12_5-THRU-ELECT_NCA | C1, C2 |
| 2 | ~ | footprints:PTC_RESET_FUSE | RF1, RF2 |
| 1 | |||
| 1 | 1000pf/3kV | footprints:CAPC3216X180N | C3 |
| 1 | 20-pin-straight | footprints:20_pin_straight | J7 |
| 1 | COM-16347 | footprints:COM-16347_SPK | LED1 |
| 1 | CRL1206-FW-R330ELF | footprints:RESC3216X70N | R7 |
| 1 | DS01C-254-S-03BE | footprints:SW_DS01C-254-S-03BE | S1 |
| 1 | ESP32-DEVKITC-32D | footprints:MODULE_ESP32-DEVKITC-32D | U1 |
| 1 | PB400EEQR1BLK | footprints:SW_PB400EEQR1BLK | S2 |
| 1 | REC5A-2405SW_H2 | footprints:CONV_REC5A-2405SW_H2 | PS1 |
| 1 | SH-7070TB | footprints:SH-7070TB_7P1X7P3_NDC | U6 |
| 1 | SS34B-HF | footprints:DO214AASMB_CIP-L | D1 |
More from Demetrius-Ross/SimMonitor
5- 2 layers83.4 × 77.2 mm
Schematic Mk3
Demetrius-Ross/SimMonitor
Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
33 parts - 2 layers87 × 55.5 mm
Schematic Mk2
Demetrius-Ross/SimMonitor
Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
29 parts - 2 layers100 × 32 mm
Signal board
Demetrius-Ross/SimMonitor
Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
28 parts - 2 layers100 × 120 mm
Board telemetry
Demetrius-Ross/SimMonitor
Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''
13 parts
Similar boards
- 2 layers75 × 50 mm
SlidersOfSociety PCB
OE1KHZ/SlidersOfSociety-PCB
A CANbus controlled closed loop motor fader module based on Microchip's PIC18F25K83
26 partsMIT - 2 layers179.5 × 53.5 mm
- 2 layers51.3 × 96.2 mm
Minisynth32
grantek/minisynth32
A 3D-printable MIDI synthesiser inspired by the Roland MT-32 and clumsyMIDI, and powered by the mt32-pi MT-32 emulator.
32 parts45CC-BY-SA-4.0 - 2 layers82 × 58 mm
Endeavour
petrmikheev/endeavour
Endeavour - open-source FPGA board and SoC ==========================================
85 parts4 - 2 layers140.4 × 80.7 mm
Game Controller
iandodson/DEN161_GameControllerDesign
Design and full report for a video game controller using an Arduino Micro
9 parts - 4 layers87.1 × 96 mm
Gsw141-breakout
rustbox/router
Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10
119 parts - 2 layers250 × 32 mm
- 4 layers284 × 185.5 mm
Questions
How big is the ESP Board PCB?
It measures 100 × 32 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP Board use?
19 parts, built around the REC5A-2405SW/H2/X1, SH-7070TB, CR1206-FX-1002ELF and UHE2A470MPD. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP Board KiCad files?
From the Demetrius-Ross/SimMonitor repository on GitHub, at the commit this page was made from: the board is Hardware-Design/board_MKIV/ESP-Board.kicad_pcb and its schematic Hardware-Design/board_MKIV/ESP-Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP Board design in my own project?
Its repository states no licence, so its author keeps all rights: ask Demetrius-Ross before reusing the design.