Skip to the content
2 layers100 × 120 mmBoard telemetry, the printed circuit board in 3D

Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

Size
100 × 120 mm
Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
47
Pads
120
Tracks, vias
234, 14
Pours
6
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Dec 2024
Updated
7 Aug 2026

Overview

Board telemetry is an open-source printed circuit board by Demetrius-Ross, from the Demetrius-Ross/SimMonitor repository on GitHub. It is a 2-layer board of 100 × 120 mm with 13 parts on 47 nets, routed with 234 tracks and 14 vias.

It is built around the REC5A-2405SW/H2/X1, SH-7070TB and UHE2A470MPD, with the DS01C-254-S-03BE, PB400EEQR1BLK and SS34B-HF among its other parts. Its parts include 3 capacitors, 2 ICs, 2 connectors, 2 switches and 1 diode. It belongs with the ESP32 boards of this library.

Main components

6

README

README.md

SimMonitoring Overview WIP

alt text

alt text

alt text

Rename the main script to main.py '''bash mv espnow_sender_relay.py main.py '''

Flash it to the ESP32: '''bash mpremote connect /dev/ttyUSB0 fs cp main.py : '''

Reset the ESP32 to run it automatically: '''bash mpremote connect /dev/ttyUSB0 reset '''

If you want manual execution, you can run any script interactively: '''bash mpremote connect /dev/ttyUSB0 run gpio_test.py '''

Wiring Guide for Each ESP32 Device

alt text

ESP32 Device ID Configuration for Sender

Below is a quick reference for how to wire GPIO17, GPIO16, GPIO4, and GPIO2 to assign a device ID (0–15). Each pin is interpreted as a bit in the 4-bit ID, read in the order (Pin2=bit0, Pin4=bit1, Pin16=bit2, Pin17=bit3).

Device IDBinary (bit3..bit0)Pin17 (bit3)Pin16 (bit2)Pin4 (bit1)Pin2 (bit0)
000000 (LOW)0 (LOW)0 (LOW)0 (LOW)
100010 (LOW)0 (LOW)0 (LOW)1 (HIGH)
200100 (LOW)0 (LOW)1 (HIGH)0 (LOW)
300110 (LOW)0 (LOW)1 (HIGH)1 (HIGH)
401000 (LOW)1 (HIGH)0 (LOW)0 (LOW)
501010 (LOW)1 (HIGH)0 (LOW)1 (HIGH)
601100 (LOW)1 (HIGH)1 (HIGH)0 (LOW)
701110 (LOW)1 (HIGH)1 (HIGH)1 (HIGH)
810001 (HIGH)0 (LOW)0 (LOW)0 (LOW)
910011 (HIGH)0 (LOW)0 (LOW)1 (HIGH)
1010101 (HIGH)0 (LOW)1 (HIGH)0 (LOW)
1110111 (HIGH)0 (LOW)1 (HIGH)1 (HIGH)
1211001 (HIGH)1 (HIGH)0 (LOW)0 (LOW)
1311011 (HIGH)1 (HIGH)0 (LOW)1 (HIGH)
1411101 (HIGH)1 (HIGH)1 (HIGH)0 (LOW)
1511111 (HIGH)1 (HIGH)1 (HIGH)1 (HIGH)

Notes

  1. GPIO2 is the least significant bit (bit0).
  2. GPIO17 is the most significant bit (bit3).
  3. Use 10kΩ resistors (or internal pulls) to pull each pin HIGH or LOW.
  4. For a Sender role, set GPIO18 = 0 (LOW) and GPIO19 = 0 (LOW). This yields role_value = 0 => "SENDER".

alt text

alt text

Parts

13
QtyValueFootprintReferences
2UHE2A470MPDfootprints:PCAP_10x12_5-THRU-ELECT_NCAC1, C2
2~footprints:PTC_RESET_FUSERF1, RF2
11000pf/3kVfootprints:CAPC3216X180NC3
120-pin-straightfootprints:20_pin_straightJ7
120_pin_90footprints:20_pin_90J6
1DS01C-254-S-03BEfootprints:SW_DS01C-254-S-03BES1
1ESP32-DEVKITC-32Dfootprints:MODULE_ESP32-DEVKITC-32DU1
1PB400EEQR1BLKfootprints:SW_PB400EEQR1BLKS2
1REC5A-2405SW_H2footprints:CONV_REC5A-2405SW_H2PS1
1SH-7070TBfootprints:SH-7070TB_7P1X7P3_NDCU6
1SS34B-HFfootprints:DO214AASMB_CIP-LD1

More from Demetrius-Ross/SimMonitor

5
  • 2 layers100.2 × 68.6 mmBoard MKIV, the printed circuit board in 3D

    Board MKIV

    Demetrius-Ross/SimMonitor

    Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

    45 parts
  • 2 layers83.4 × 77.2 mmSchematic Mk3, the printed circuit board in 3D

    Schematic Mk3

    Demetrius-Ross/SimMonitor

    Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

    33 parts
  • 2 layers87 × 55.5 mmSchematic Mk2, the printed circuit board in 3D

    Schematic Mk2

    Demetrius-Ross/SimMonitor

    Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

    29 parts
  • 2 layers100 × 32 mmSignal board, the printed circuit board in 3D

    Signal board

    Demetrius-Ross/SimMonitor

    Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

    28 parts
  • 2 layers100 × 32 mmESP Board, the printed circuit board in 3D

    ESP Board

    Demetrius-Ross/SimMonitor

    Rename the main script to main.py '''bash mv espnowsenderrelay.py main.py '''

    19 parts

Similar boards

  • 2 layers75 × 50 mmSlidersOfSociety PCB, the printed circuit board in 3D

    SlidersOfSociety PCB

    OE1KHZ/SlidersOfSociety-PCB

    A CANbus controlled closed loop motor fader module based on Microchip's PIC18F25K83

    26 partsMIT
  • 2 layers51.3 × 96.2 mmMinisynth32, the printed circuit board in 3D

    Minisynth32

    grantek/minisynth32

    A 3D-printable MIDI synthesiser inspired by the Roland MT-32 and clumsyMIDI, and powered by the mt32-pi MT-32 emulator.

    32 parts45CC-BY-SA-4.0
  • 2 layers82 × 58 mmEndeavour, the printed circuit board in 3D

    Endeavour

    petrmikheev/endeavour

    Endeavour - open-source FPGA board and SoC ==========================================

    85 parts4
  • 2 layers140.4 × 80.7 mmGame Controller, the printed circuit board in 3D

    Game Controller

    iandodson/DEN161_GameControllerDesign

    Design and full report for a video game controller using an Arduino Micro

    9 parts
  • 4 layers87.1 × 96 mmGsw141-breakout, the printed circuit board in 3D

    Gsw141-breakout

    rustbox/router

    Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10

    119 parts
  • 2 layers250 × 32 mmPsu, the printed circuit board in 3D

    Psu

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    31 parts222
  • 4 layers284 × 185.5 mmHog, the printed circuit board in 3D

    Hog

    shmoergh/hog

    Fully analog two-voice monophonic synth for live performances

    210 parts124
  • 4 layers30.3 × 90.5 mmBase station, the printed circuit board in 3D

    Base station

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    115 parts1GPL-3.0

Questions

How big is the Board telemetry PCB?

It measures 100 × 120 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Board telemetry use?

13 parts, built around the REC5A-2405SW/H2/X1, SH-7070TB, UHE2A470MPD and DS01C-254-S-03BE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Board telemetry KiCad files?

From the Demetrius-Ross/SimMonitor repository on GitHub, at the commit this page was made from: the board is Hardware-Design/board_telemetry/board_telemetry/board_telemetry.kicad_pcb and its schematic Hardware-Design/board_MKIV/ESP-Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Board telemetry design in my own project?

Its repository states no licence, so its author keeps all rights: ask Demetrius-Ross before reusing the design.