
Phil ESC
deagle205/Whoop_1S_FC
Phil: 1S brushless whoop flight controller, 4-in-1 ESC and VTX (KiCad 10)

Phil: 1S brushless whoop flight controller, 4-in-1 ESC and VTX (KiCad 10)
Whoop 1S FC is an open-source printed circuit board by deagle205, from the deagle205/Whoop_1S_FC repository on GitHub. It is a 6-layer board of 19 × 19 mm with 96 parts on 125 nets, routed with 1,316 tracks and 163 vias.
It is built around the STM32G473MEY6, ESP8285N08 and SX1281IMLTRT, with the SPL06-001, TPS63802DLAR and ICM-42688-P among its other parts. Its parts include 34 capacitors, 22 resistors, 7 ICs, 6 diodes and 4 connectors. It belongs with the robots and motor control boards and the ESP8266 and STM32 boards of this library.
Three stacked 19x19 / 16x16 boards on a 12.8 mm M1.4 screw square:
Whoop_1S_FC.*: flight controller (STM32G473 WLCSP-81, ICM-42688-P, SPL06, ELRS SX1281 + ESP8285, TPS63802)Phil_ESC/: 4-in-1 Bluejay ESC (4x EFM8BB51, 12x SiA517DJ)Phil_VTX/: 5.8 GHz VTX (RTC6705 + SE5004L), AT7456E OSD, blackbox flash, 5 V boostShared libraries: WhoopFC.kicad_sym, WhoopFC.pretty/, WhoopFC.3dshapes/.
Note: 3D model paths in the footprints are absolute (C:/Users/Survi/...), so other machines won't show them without editing.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nF | Capacitor_SMD:C_0201_0603Metric | C103, C104, C105, C106, C107, C110, C203, C205, C301, C303, C304, C314, C322, C508 |
| 6 | 10k | Resistor_SMD:R_0201_0603Metric | R101, R303, R308, R310, R505, R506 |
| 5 | 1k | Resistor_SMD:R_0201_0603Metric | R102, R103, R104, R304, R507 |
| 5 | TBD | Capacitor_SMD:C_0201_0603Metric | C310, C318, C319, C320, C321 |
| 4 | 100R | Resistor_SMD:R_0201_0603Metric | R801, R802, R803, R804 |
| 4 | 10pF | Capacitor_SMD:C_0201_0603Metric | C101, C102, C324, C325 |
| 3 | 10nF | Capacitor_SMD:C_0201_0603Metric | C201, C302, C308 |
| 2 | 100k | Resistor_SMD:R_0201_0603Metric | R502, R508 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C315, C502 |
| 2 | 4.7k | Resistor_SMD:R_0201_0603Metric | R201, R202 |
| 2 | M1.4 GND | WhoopFC:MountingHole_1.6mm_M1.4_Pad_2.6mm | H2, H4 |
| 2 | M1.4 Vin | WhoopFC:MountingHole_1.6mm_M1.4_Pad_2.6mm | H1, H3 |
| 2 | TBD | Inductor_SMD:L_0201_0603Metric | L302, L303 |
| 1 | 0.47uH | Inductor_SMD:L_Murata_DFE201610P | L501 |
| 1 | 100uF 6.3V polymer | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C501 |
| 1 | 12k 1% | Resistor_SMD:R_0201_0603Metric | R301 |
| 1 | 15uH | Inductor_SMD:L_0603_1608Metric | L301 |
| 1 | 1nF | Capacitor_SMD:C_0201_0603Metric | C317 |
| 1 | 1uF | Capacitor_SMD:C_0201_0603Metric | C108 |
| 1 | 2.2uF | Capacitor_SMD:C_0201_0603Metric | C202 |
| 1 | 2450AT18A100 | RF_Antenna:Johanson_2450AT18x100 | AE301 |
| 1 | 26MHz | Crystal:Crystal_SMD_WE_IQXC-26-4Pin_1.6x1.2mm | Y302 |
| 1 | 470nF | Capacitor_SMD:C_0201_0603Metric | C306 |
| 1 | 47uF | Capacitor_SMD:C_0603_1608Metric | C503 |
| 1 | 499R | Resistor_SMD:R_0201_0603Metric | R309 |
| 1 | 52MHz TCXO | Oscillator:Oscillator_SMD_SiT_PQFN-4Pin_2.0x1.6mm | Y301 |
| 1 | 560k | Resistor_SMD:R_0201_0603Metric | R501 |
| 1 | 600R@100MHz | Inductor_SMD:L_0402_1005Metric | FB201 |
| 1 | 8MHz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y101 |
| 1 | BIND/BOOT | WhoopFC:TP_Probe_D0.6mm | TP301 |
| 1 | BOOT0 | WhoopFC:TP_Probe_D0.6mm | TP101 |
| 1 | Blue | LED_SMD:LED_0201_0603Metric | D101 |
| 1 | ESD131-B1-W0201 | Diode_SMD:Infineon_SG-WLL-2-3_0.58x0.28_P0.36mm | D301 |
| 1 | ESP8285 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.7x3.7mm | U302 |
| 1 | FLASH_CS link | WhoopFC:TP_Wire_1.5x2.0mm | J902 |
| 1 | Green | LED_SMD:LED_0201_0603Metric | D302 |
| 1 | ICM-42688-P | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U201 |
| 1 | LED_STRIP | WhoopFC:TP_Wire_1.5x2.0mm | TP102 |
| 1 | NRST | WhoopFC:TP_Probe_D0.6mm | TP707 |
| 1 | Orange | LED_SMD:LED_0201_0603Metric | D102 |
| 1 | Red | LED_SMD:LED_0201_0603Metric | D502 |
| 1 | SPL06-001 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U202 |
| 1 | STM32G473MEY6 | Package_CSP:ST_WLCSP-81_4.02x4.27mm_Layout9x9_P0.4mm | U101 |
| 1 | SWCLK | WhoopFC:TP_Probe_D0.6mm | TP706 |
| 1 | SWDIO | WhoopFC:TP_Probe_D0.6mm | TP705 |
| 1 | SX1281IMLTRT | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U301 |
| 1 | Socket 1x4 1.27 | Connector_PinSocket_1.27mm:PinSocket_1x04_P1.27mm_Vertical | J801 |
| 1 | TPS63802DLAR | WhoopFC:Texas_VSON-HR-10_2x3mm_P0.5mm_DLA0010A | U501 |
| 1 | UART_RX | WhoopFC:TP_Probe_D0.6mm | TP709 |
| 1 | UART_TX | WhoopFC:TP_Probe_D0.6mm | TP708 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U701 |
| 1 | USB_POGO | WhoopFC:Pogo_1x04_P1.27mm_D0.9mm | J701 |
| 1 | VBAT+ | WhoopFC:TP_Battery_1.5x2.2mm | TP501 |
| 1 | VBAT- | WhoopFC:TP_Battery_1.5x2.2mm | TP502 |
| 1 | VTX link pads | WhoopFC:Pads_2x05_P1.8mm_1.5x2.0mm | J901 |
| 1 | Yellow | LED_SMD:LED_0201_0603Metric | D103 |

OpenDrone-hw/OpenAIO
Open-source AIO for 2-6S toothpick quads: flight controller, 4-in-1 AM32 ESC and ExpressLRS receiver, 25.5x25.5 mm.

MidwestMotorBoy/Battery-Bank
Monolith: an ultralight IP67 power bank for backpacking. 4S BAK 65E 21700 (91 Wh, under the 100 Wh airline limit), two bidirectional 100 W USB-C PD ports, Bluetooth LE (TI CC2340) with an iPhone app.


anticitizn/p4eregrine
All-in-one ESP32 P4-based drone ESC, flight controller, and video processor

sudo-junkie/Controller
ESP32-based replacement PCB for UCOM USB game controller, with LCD, IMU, IR TX/RX and more...

OpenDrone-hw/OpenFC-Lite-Mini
Open-source Betaflight flight controller. RP2354A, 20x20 mm, 6-layer, 3-6S, CERN-OHL-S-2.0.

OpenDrone-hw/OpenFC-Lite
Open-source Betaflight flight controller. RP2354B, 30.5x30.5 mm, 6-layer, 3-8S, CERN-OHL-S-2.0.

sneakylizard123-4/Dreamscape-F405-2020
a 20x20mm flight controller for 3" fpv drone
It measures 19 × 19 mm and has 6 copper layers, 0.88 mm thick.
96 parts, built around the STM32G473MEY6, ESP8285N08, SX1281IMLTRT and SPL06-001. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the deagle205/Whoop_1S_FC repository on GitHub, at the commit this page was made from: the board is Whoop_1S_FC.kicad_pcb and its schematic Phil_ESC/Phil_ESC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask deagle205 before reusing the design.