Skip to the content
2 layers40 × 37 mmSpectralist LEDs, the printed circuit board in 3D

Spectralist LEDs

dchwebb/Spectralist9

Eurorack Additive Synthesizer

Size
40 × 37 mm
Copper layers
2
Thickness
1.6 mm
Parts
34
Nets
32
Pads
134
Tracks, vias
255, 32
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
10 Oct 2024
Updated
7 Apr 2025

Overview

Spectralist LEDs is an open-source printed circuit board by dchwebb, from the dchwebb/Spectralist repository on GitHub. It is a 2-layer board of 40 × 37 mm with 34 parts on 32 nets, routed with 255 tracks and 32 vias.

Its parts include 25 diodes, 3 resistors, 3 connectors, 2 capacitors and 1 IC. It belongs with the audio and music boards of this library.

README

README.md

Spectralist

Overview

Image

Spectralist is an additive oscillator for Eurorack modular synthesisers. Up to 300 harmonics are output over two separate Odd and Even channels with a 'filter' offering a range of options for sculpting the harmonic spectrum of the output signals.

There are two harmonic modes - individual harmonics and sinusoidal waves of harmonics. In individual harmonic mode the spread controls adjust the spacing of the harmonics and the warp control either progressively bunches up or spreads out the harmonics. In the sinusoidal mode the spread controls increase the frequency of the 'waves' of harmonics.

The filter can be selected as a low pass filter with continuously adjustable slope or as a comb filter with adjustable tooth width and spread. In the comb filter mode the channel filter controls set the width between teeth and the slope sets the rise and fall times of the teeth. The individual channel filters controls can be adjusted with potentiometers or by CV with with trimmers to attenuate.

The pan CV input allows each channel to be smoothly panned between the two outputs. This can be used to mix the signals together in a mono setup, or used to dynamically shift the harmonics in the stereo field.

In the centre of the module is a ring of LEDs that give a visual representation of the harmonic spread and warp settings.

The module was designed in conjunction with musician Tal Shoshani who produced the following demonstration video:

IMAGE ALT TEXT HERE

Technical

Image

The module is based around an STM32H723VGT microcontroller, clocked at 400MHz. A TI PCM5100APW 32 bit audio DAC is used for the two channel outputs.

A TL072 dual op-amps is used to amplify and filter the DAC output (and/or phase invert) the outputs from 3V to 9V peak-to-peak at maximum. Input CV signals are conditioned by MCP6004 op-amps.

A USB B micro port is available at the rear of the unit for software updgrades and configuration via a serial connection.

The animated 25 LED display is driven over I2C by a PCA9956B LED Driver and the SMD LEDs sit on a daughter board raising them to the level of the front panel.

Components schematic

LED daughterboard schematic

Controls schematic

Power

Analog power is supplied via a 3.3V LDO regulator and digital power uses a TPS561201 switching power supply.

  • +12V current draw: 139 mA
  • -12V Current draw: 7 mA

Errata

Panel Errata: Mode switch hole too large for subminiature switch Filter type switch hole just too narrow Harm_Warp_pot and Harm_Stretch_Pot wrong way round (fixed 1.1)

Parts

34
QtyValueFootprintReferences
25LEDLED_SMD:LED_0603_1608MetricD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +9
210kResistor_SMD:R_0603_1608MetricR1, R3
2Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2, J3
1100nFCapacitor_SMD:C_0603_1608MetricC1
110uFCapacitor_SMD:C_0805_2012MetricC2
12kResistor_SMD:R_0603_1608MetricR2
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1PCA9956B_LED_DriverCustom_Footprints:HTSSOP-38_4.4x9.7mm_P0.5mmU1

More from dchwebb/Spectralist

2

Similar boards

  • 2 layers26 × 30 mmMicrocontroller, the printed circuit board in 3D

    Microcontroller

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    34 parts1.1kCC-BY-4.0
  • 2 layers171.2 × 72.9 mmAmiga gfxcard old, the printed circuit board in 3D

    Amiga gfxcard old

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    34 parts1k
  • 2 layers53.5 × 62.5 mmLed matrix, the printed circuit board in 3D

    Led matrix

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    34 parts915
  • 2 layers45 × 26 mmESP32-HELP Button, the printed circuit board in 3D

    ESP32-HELP Button

    pcbreflux/espressif

    all espressif stuff will committed here

    34 parts608GPL-3.0
  • 2 layers41.7 × 25.7 mmHeadphones flex pcb rigid, the printed circuit board in 3D

    Headphones flex pcb rigid

    strangeparts/niubi-headphones

    Flexible circuit board design for adding a headphone jack to an iPhone 7

    34 parts493MIT
  • 2 layers18.8 × 16.3 mmAmoeba, the printed circuit board in 3D

    Amoeba

    mtl/keyboard-pcbs

    Keyboard PCBs

    34 parts485
  • 2 layers127 × 69.9 mmEzcgi, the printed circuit board in 3D

    Ezcgi

    baldengineer/bit-preserve

    Project for capturing vintage, classic, aka old computer schematics in KiCad.

    34 parts446

Questions

How big is the Spectralist LEDs PCB?

It measures 40 × 37 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Spectralist LEDs use?

34 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Spectralist LEDs KiCad files?

From the dchwebb/Spectralist repository on GitHub, at the commit this page was made from: the board is Hardware/Spectralist_LEDs.kicad_pcb and its schematic Hardware/Spectralist_Components.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Spectralist LEDs design in my own project?

Its repository states no licence, so its author keeps all rights: ask dchwebb before reusing the design.