

TX BOARD
Cost Effective HF transceiver based on max1000 FPGA module
- Size
- 99.1 × 99.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 104
- Nets
- 64
- Pads
- 272
- Tracks, vias
- 665, 641
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20200104)
- Created
- 11 Jan 2020
- Updated
- 7 Apr 2021
Overview
TX BOARD is an open-source printed circuit board by dawsonjon, from the dawsonjon/OpenXcvr repository on GitHub, published under the MIT licence. It is a 2-layer board of 99.1 × 99.1 mm with 104 parts on 64 nets, routed with 665 tracks and 641 vias.
It is built around the MCP1406-E/P, 74AC00 and BS170, with the 1N4148W among its other parts. Its parts include 28 capacitors, 20 resistors, 15 inductors, 8 diodes and 6 ICs. It belongs with the radio and wireless and fPGA and programmable logic boards of this library.
Main components
4MCP1406-E/P
PDIP-8-40℃~+125℃ 1 130uA 20ns 20ns 4.5V~18V 6A 6A MOSFET PDIP-8 Gate Drivers ROHSMicrochip TechnologyGate Drivers74AC00
--40℃~+85℃ 100mV、360mV 2 2.1V、3.15V、3.85V 2.9V、4.4V、5.4V 24mA 24mA 2V~6V 2uA 4 74AC Series 900mV、1.35V、1.65V 9ns@5V NAND Gate - Logic Gates ROHSonsemiLogic GatesBS170
TO-92-55℃~+150℃ 1 N-channel 1.2Ω@10V 17pF 2.1V 24pF 500mA 60V 7pF 830mW N-Channel TO-92 MOSFETs ROHSonsemiMOSFETs1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching Diodes
README
README.mdOpen XCVR
A cheap open-source Ham radio transceiver based on the MAX1000 FPGA module.
Features
- High performance Intel MAX10 FPGA based DSP
- SDR receiver 0.5-30MHz continuous
- SDR transmitter 80m-10m ham bands
- efficient 5W (ish) switched-mode PA for extended battery operation
- Supports AM, FM, SSB and CW modes
- audio output via 3.5mm headphone jack with integrated amplifier and provision for internal speaker
- audio input via 3.5mm microphone jack with integrated pre-amplifier and provision for internal mic
- support for straight and iambic telagraph keys with integrated electronic keyer
- 500 general purpose memories
- external 12v power via 2.5mm barrel jack provision for internal battery, integrated battery monitor
- integrated Power/SWR meter
- provision for GPS frequency calibration
The wiki contains a detailed description of the hardware and firmware design
Parts
104| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100n | Capacitor_SMD:C_0805_2012Metric | C17, C20, C22, C23, C24, C27, C28 |
| 7 | 10k | Resistor_SMD:R_0805_2012Metric | R4, R5, R7, R12, R13, R19, R21 |
| 6 | BS170 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | 100 | Resistor_SMD:R_0805_2012Metric | R6, R9, R10, R11 |
| 4 | 1N4148W | Diode_SMD:D_SOD-123 | D1, D2, D3, D4 |
| 4 | G5V-2 | Relay_THT:Relay_DPDT_Omron_G5V-2 | K1, K2, K3, K4 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 3 | 10K | Resistor_SMD:R_0805_2012Metric | R1, R2, R3 |
| 3 | 4k7 | Resistor_SMD:R_0805_2012Metric | R16, R17, R18 |
| 2 | 1.2n | Capacitor_SMD:C_0805_2012Metric | C8, C12 |
| 2 | 1.380u | openxcvr:FT37-INDUCTOR | L3, L11 |
| 2 | 10 | Resistor_SMD:R_0805_2012Metric | R14, R15 |
| 2 | 100u | openxcvr:L_SMT_INDUCTOR | L13, L14 |
| 2 | 10u | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C18, C19 |
| 2 | 150p | Capacitor_SMD:C_0805_2012Metric | C5, C9 |
| 2 | 180p | Capacitor_SMD:C_0805_2012Metric | C2, C14 |
| 2 | 1N5711 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D5, D6 |
| 2 | 2.434u | openxcvr:FT37-INDUCTOR | L4, L12 |
| 2 | 270p | Capacitor_SMD:C_0805_2012Metric | C3, C15 |
| 2 | 303n | openxcvr:FT37-INDUCTOR | L1, L9 |
| 2 | 390p | Capacitor_SMD:C_0805_2012Metric | C6, C10 |
| 2 | 470p | Capacitor_SMD:C_0805_2012Metric | C4, C16 |
| 2 | 56p | Capacitor_SMD:C_0805_2012Metric | C1, C13 |
| 2 | 680p | Capacitor_SMD:C_0805_2012Metric | C7, C11 |
| 2 | 68n | Capacitor_SMD:C_0805_2012Metric | C21, C26 |
| 2 | 773n | openxcvr:FT37-INDUCTOR | L2, L10 |
| 2 | FT50-43Transformer | openxcvr:FT50-43 Transformer | TR1, TR2 |
| 2 | to220heatsink | openxcvr:to220 heatsink | U2, U3 |
| 1 | 1.698u | openxcvr:FT37-INDUCTOR | L7 |
| 1 | 10k | Potentiometer_THT:Potentiometer_Piher_PT-6-V_Vertical | RV1 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R8 |
| 1 | 220n | Capacitor_SMD:C_0805_2012Metric | C25 |
| 1 | 3.012u | openxcvr:FT37-INDUCTOR | L8 |
| 1 | 382n | openxcvr:FT37-INDUCTOR | L5 |
| 1 | 44 u | openxcvr:FT50-43 INDUCTOR | L15 |
| 1 | 51v | Diode_SMD:D_SOD-123 | D8 |
| 1 | 74AC00 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U6 |
| 1 | 904n | openxcvr:FT37-INDUCTOR | L6 |
| 1 | Antenna BNC Connector | Connector_Coaxial:BNC_Amphenol_B6252HB-NPP3G-50_Horizontal | J1 |
| 1 | Battery Connector | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | DMC3056LSS | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | D_Schottky | openxcvr:D_SOD-106 | D7 |
| 1 | LM7805CV_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | MCP1406 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | POWER SWITCH | openxcvr:RS PCB Toggle Switch | SW1 |
| 1 | Power Jack | Connector_BarrelJack:BarrelJack_Horizontal | J3 |
| 1 | RADIO BOARD CONNECTOR | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J2 |
The 99 most common of 104 parts.
More from dawsonjon/OpenXcvr
2- 2 layers101.6 × 137.4 mm

- 2 layers99.1 × 99.1 mm

Similar boards
- 4 layers78 × 47 mm

- 2 layers88.9 × 88.9 mm

- 2 layers

BreadBin
c0pperdragon/BreadBin
A CPU made of 7400 logic on breadboards - inside a bread bin ;-)
45 parts18 - 2 layers53.3 × 53.3 mm

- 2 layers101.6 × 83.8 mm

Z80DevBoard
dbuchwald/Z80DevBoard
Simple Z80 based prototyping and development board designed as extension to Arduino Mega 2560
39 parts3MIT - 2 layers88.9 × 71.1 mm

- 2 layers150 × 100 mm

- 2 layers172.7 × 108.6 mm

Clementina hardware
fran150/clementina-hardware
KiCad schematic for Clementina, a 3.3V W65C02S computer with a Raspberry Pi Pico 2 W (MIA) handling video, audio, storage and I/O.
48 partsGPL-3.0
Questions
How big is the TX BOARD PCB?
It measures 99.1 × 99.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the TX BOARD use?
104 parts, built around the MCP1406-E/P, 74AC00, BS170 and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TX BOARD KiCad files?
From the dawsonjon/OpenXcvr repository on GitHub, at the commit this page was made from: the board is pcb/openxcvr/TX_BOARD.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TX BOARD design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).