Skip to the content
2 layers42.3 × 42.3 mmBioreactor parallel pcb v1, the printed circuit board in 3D

Bioreactor parallel pcb v1

danlil666/EFRI_bioreactor

This repository hosts files to build and operate Machine Agency Bioreactor, a modular toolkit for developing custom bioreactors.

Size
42.3 × 42.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
22
Nets
37
Pads
119
Tracks, vias
339, 25
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
5 Mar 2025
Updated
11 May 2026

Overview

Bioreactor parallel pcb v1 is an open-source printed circuit board by danlil666, from the danlil666/EFRI_bioreactor repository on GitHub. It is a 2-layer board of 42.3 × 42.3 mm with 22 parts on 37 nets, routed with 339 tracks and 25 vias.

It is built around the DMG3415U-7 and ZLDO1117GTA. Its parts include 5 resistors, 4 capacitors, 3 ICs, 2 transistors and 1 diode. It belongs with the SAM D and SAM boards of this library.

Main components

2

README

README.md

bioreactor

This repository hosts files to build and operate Machine Agency Bioreactor, a modular toolkit for developing custom bioreactors. Our toolkit contains custom hardware and software for adding chemicals, monitoring the mixture, and refining outputs. The current toolkit is designed to support beer brewing application, an automated process which involves several biochemical reactions that are comparable to other synthetic biology processes.

using Seeed Xiao (WIP)

I'm learning how to use CircuitPython on Seeed Xiao to further offload the programming complexity of using Arduino.

I still want to establish serial communication between the laptop and the Xiao boards. To do so, I started with establishing a debugging REPL using MacOS's built-in terminal.

Connecting to the Serial Console

Connecting to the serial console on Mac does not require installing any drivers or extra software. You'll use a terminal program to find your board, and screen to connect to it. Terminal and screen both come installed by default.

The easiest way to determine which port the board is using is to first check without the board plugged in. Open Terminal and type the following:

text
ls /dev/tty.*

Now, plug your board. In Terminal, type ls /dev/tty.* again. It shows

text
/dev/tty.usbmodem[some_number]

on my terminal. The last few digits might change depending on which particular port Xiao is plugged in.

Connect with screen

Now that you know the name your board is using, you're ready connect to the serial console. You're going to use a command called screen. The screen command is included with MacOS. To connect to the serial console, use Terminal. Type the following command, replacing board_name with the name you found your board is using:

text
screen /dev/tty.usbmodem142401 115200

Press enter to run the command. It will open in the same window. If no code is running, the window will be blank. Otherwise, you'll see the output of your code.

Press Ctrl + C to enter interactive REPL.

To exit Screen session completely:

Make sure the Terminal window has focus.

Type Ctrl+A (you won’t see anything displayed yet)

Then type Ctrl+\ (the forward slash is located below Delete)

At the bottom of the Terminal window, you should see “Really quit and kill all your windows [y/n]”. Type “y”.

ESP32S3

I was using Xiao SAMD21 and there is a very good guide on how to get CircuitPython on it. However, Seeed Xiao SAMD21 has a limited flash, only 48kb after installing CircuitPython. With my luck I managed to stuffed in stepper motor libraries, but I was stuck on getting I2C and bus libraries. For these libraries, using Seeed Xiao ESP32S3 is a viable alternative because it has MBs of flash available.

The following steps are adapted from this wonderful guide.

Installing CircuitPython on ESP32

There is no Xiao ESP32S3-specific CircuitPython .bin firmware as of Jan 21 2024, so using Espressif - ESP32-S3-DevKitM-1-N8 is currently the best way to do it. Download the latest .bin from the link.

Installing the Firmware

This must be done over serial. I'm using esptool, but there is also guidance on how to use the web serial browser based tool (easy method, but requires a Chrome webbrowser).

In the terminal, install esptool using pip if you haven't yet. More instruction can be found here

text
pip install esptool

Find all serial devices by running ls /dev/tty.*. On Mac it is usually /dev/tty.usbmodem******.

Once you have esptool installed, you will first want to erase the flash on your ESP32 board, it's also a great way to determine that you are able to connect. Change the serial address to the one that shows up on your terminal. I'm using ESP32S3 so the chip argument is also changed.

esptool.py --chip esp32s3 --port /dev/tty.usbmodem142401 erase_flash

If you're not 100% sure which ESP32 chip you have, you can just specify the port: esptool.py --port /dev/tty.usbmodem****** erase_flash

Once the flash is successfully erased, you can load your firmware .bin file by running something similar to the command below. Make sure you update the following:

  • The port to match the serial port to which your board is connected, i.e. change /dev/tty.usbsmodem****** to match your connection.

  • The firmware.bin file name to match the firmware you downloaded, i.e. change firmware.bin to something like adafruit-circuitpython-espressif_esp32s3_devkitm_1_n8-en_US-8.2.9.bin.

  • This command assumes you will be loading it to address 0x0, as we do for circuitpython. This may not be true for your firmware! check the documentation for the offset if necessary.

Load the firmware using something similar to the following command, with the above changes:

esptool.py --port /dev/tty.usbmodem142401 write_flash -z 0x0 adafruit-circuitpython-espressif_esp32s3_devkitm_1_n8-en_US-9.2.0.bin

You will then see a flash storage unit named CIRCUITPY popping up.

Connect the XIAO ESP32S3 board to PC under the BootLoader Mode

Step 1. Press and hold the BOOT button on the XIAO ESP32S3 without releasing it.

Step 2. Keep the BOOT button pressed and then connect to the computer via the data cable. Release the BOOT button after connecting to the computer.

Step 3. Upload the Blink program to check the operation of the XIAO ESP32S3.

Parts

22
QtyValueFootprintReferences
310kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R4, R5
2100uFCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC1, C2
2Conn_01x04_PinTE_connector:640457-4_TYCMOTOR1, MOTOR2
2DMG3415Package_TO_SOT_SMD:SOT-23Q1, Q2
2TB6612FNGPackage_SO:SSOP-24_5.3x8.2mm_P0.65mmU2, U3
10.1uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC3
110Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR3
110uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC4
1110Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2
1Conn_01x02_PinTE_connector:640455-2_TYCVMOTOR_chain1
1Conn_01x04_PinConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalI2C1
1J1TE_connector:640455-2_TYCVin1
1LEDTE_connector:640455-2_TYCD1
1R1000PVG3G:PVG3G_BRNRV1
1SeeeduinoXIAOseeed_xiao:Seeeduino XIAO-MOUDLE14P-2.54-21X17.8MMU1
1ZLDO1117Package_TO_SOT_SMD:SOT-223Reg1

More from danlil666/EFRI_bioreactor

1
  • 2 layers35.6 × 35.6 mmBioreactor pcb, the printed circuit board in 3D

    Bioreactor pcb

    danlil666/EFRI_bioreactor

    This repository hosts files to build and operate Machine Agency Bioreactor, a modular toolkit for developing custom bioreactors.

    10 parts

Similar boards

  • 2 layers99.8 × 99.8 mmStmbl 5.0, the printed circuit board in 3D

    Stmbl 5.0

    freakontrol/stmbl

    THE AUTHORS OF THIS SOFTWARE ACCEPT ABSOLUTELY NO LIABILITY FOR ANY HARM OR LOSS RESULTING FROM ITS USE. IT IS EXTREMELY UNWISE TO RELY ON SOFTWARE ALONE FOR SAFETY.

    432 parts53GPL-3.0
  • 2 layers78 × 50.7 mmStm32-48pin devBoard, the printed circuit board in 3D

    Stm32-48pin devBoard

    joeferner/stm32-48pin-devBoard

    STM32 48pin Development Board.

    42 parts4
  • 2 layers84.6 × 84.6 mmTelepresenceRobot, the printed circuit board in 3D

    TelepresenceRobot

    joeferner/telepresenceRobot

    Telepresence Robot

    133 parts3
  • 4 layers80 × 51 mmBrdOut, the printed circuit board in 3D

    BrdOut

    embeddedee/IsoNxpDmxRdm

    Isolated variant of NXP's AN11154 USB to DMX/RDM master

    60 parts1
  • 2 layers100 × 100 mmStmbl 4.0, the printed circuit board in 3D

    Stmbl 4.0

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    433 parts990GPL-3.0
  • 2 layers100 × 100 mmStmbl 4.0, the printed circuit board in 3D

    Stmbl 4.0

    coon42/stmbl_otter

    sudo dfu-util -d 0483:df11 -a 0 -s 0x8000000:leave -D objhvf3/hvf3.bin

    425 parts1GPL-3.0
  • 2 layers36.8 × 27.3 mmTiny44 ghost, the printed circuit board in 3D

    Tiny44 ghost

    danlil666/documentation

    This is the starting point of me trying to use GitHub.

    11 partsMIT

Questions

How big is the Bioreactor parallel pcb v1 PCB?

It measures 42.3 × 42.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Bioreactor parallel pcb v1 use?

22 parts, built around the DMG3415U-7 and ZLDO1117GTA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bioreactor parallel pcb v1 KiCad files?

From the danlil666/EFRI_bioreactor repository on GitHub, at the commit this page was made from: the board is bioreactor_parallel_pcb_v1/bioreactor_parallel_pcb_v1.kicad_pcb and its schematic bioreactor_parallel_pcb_v1/bioreactor_parallel_pcb_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bioreactor parallel pcb v1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask danlil666 before reusing the design.