Skip to the content
2 layers75 × 44 mmPlacaESP, the printed circuit board in 3D

Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

Size
75 × 44 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
29
Pads
72
Tracks, vias
67, 8
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 May 2022
Updated
29 Oct 2026

Overview

PlacaESP is an open-source printed circuit board by danielvie, from the danielvie/doutorado repository on GitHub. It is a 2-layer board of 75 × 44 mm with 17 parts on 29 nets, routed with 67 tracks and 8 vias.

Its parts include 3 connectors and 2 capacitors.

README

README.md

Doutorado

Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

Quick links

Where to go

NeedGo to
Thesis and paper LaTeX sourcesLATEX/
Plans, TODOs, and qualification materialresearch-material/planning/
Reviewer commentsresearch-material/review-feedback/
Authored analysis and meeting notesresearch-material/working-notes/
Shared diagrams and writing assetsassets/
Current MATLAB simulations/control codesimulations/matlab-sim/
Older MATLAB simulationssimulations/legacy/
Projection/feasibility-region MATLAB worksimulations/projection/
ESP32 firmware, hardware docs, and web UIembedded/
External papers, books, theses, and course materialresearch-material/literature/
Presentations and slidespresentations/
External/vendor materialz_dependencies/, z_kawa/, z_mpt_install/, and z_qpoases/

Common commands

This repository uses Taskfile.yml:

sh
task --list

Important tasks:

  • task run opens generated overview documentation.
  • task test validates generated overview documentation.
  • task clean removes generated overview documentation.
  • task update-tese copies LATEX/thesis/build/tese.pdf to the repository root.

Navigation conventions

  • Start from this README, then use docs/REPO_MAP.md for locations and CONTEXT.md for terminology.
  • Prefer area-specific READMEs/docs when they exist.
  • Treat z_dependencies/, z_kawa/, z_mpt_install/, z_qpoases/, and simulations/backup/ as backup, vendored, or auxiliary material unless a task explicitly points there.
  • Prefer simulations/matlab-sim/ over simulations/legacy/ for current simulation work.
  • Prefer embedded/esp32_idf/ for current ESP32 firmware work.
  • Avoid adding new loose files at the repository root; put new material in the closest project area.
  • Keep document navigation folders at most three levels deep. Self-contained source/build trees are exempt when flattening would break them.

Parts

17
QtyValueFootprintReferences
12~TestPoint:TestPoint_Bridge_Pitch2.54mm_Drill0.7mmTP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12
2Conn_01x15Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_VerticalJ7, J8
1100 nFCapacitor_THT:C_Disc_D6.0mm_W2.5mm_P5.00mmC7
1100uF/25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC4
1Conn_02x07_Odd_EvenConnector_IDC:IDC-Header_2x07_P2.54mm_VerticalJ12

More from danielvie/doutorado

2
  • 2 layers140 × 77 mmPlaca Mae, the printed circuit board in 3D

    Placa Mae

    danielvie/doutorado

    Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

    30 parts
  • 2 layers25 × 25 mmPlaca Carga, the printed circuit board in 3D

    Placa Carga

    danielvie/doutorado

    Repository for thesis writing, simulations, embedded experiments, presentations, publications, and supporting research material.

    12 parts

Similar boards

  • 2 layers50 × 35 mmServo power, the printed circuit board in 3D

    Servo power

    earthtojake/text-to-cad

    Design physical products with AI

    17 parts26kMIT
  • 2 layers139.7 × 62.2 mmBreakout 60pin EEC IV, the printed circuit board in 3D

    Breakout 60pin EEC IV

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    17 parts1.2k
  • 2 layers29.2 × 55.9 mmDeniseadapter, the printed circuit board in 3D

    Deniseadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    17 parts1kGPL-3.0
  • 2 layers24.5 × 36.5 mmCluster, the printed circuit board in 3D

    Cluster

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    17 parts993
  • 2 layers56.3 × 55.7 mmStarNecklace, the printed circuit board in 3D

    StarNecklace

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    17 parts915
  • 2 layers25 × 25 mmSmallEncoder, the printed circuit board in 3D

    SmallEncoder

    DDeGonge/OS-ARM

    This arm is not industrial and it will not be fast, but that is not my goal. But it will hopefully be a very nice looking arm fully capable of 6dof motion, cheap enough to keep it accessable but capable enough to…

    17 parts498MIT
  • 2 layers38.9 × 16.1 mmAmoeba spc, the printed circuit board in 3D

    Amoeba spc

    mtl/keyboard-pcbs

    Keyboard PCBs

    17 parts485
  • 2 layers36 × 51 mmABSIS ALE, the printed circuit board in 3D

    ABSIS ALE

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    17 parts431

Questions

How big is the PlacaESP PCB?

It measures 75 × 44 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PlacaESP use?

17 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PlacaESP KiCad files?

From the danielvie/doutorado repository on GitHub, at the commit this page was made from: the board is embedded/kicad/PlacaDaniel/PlacaESP_Rev3/PlacaESP.kicad_pcb and its schematic embedded/kicad/PlacaDaniel/PlacaESP_Rev3/PlacaESP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PlacaESP design in my own project?

Its repository states no licence, so its author keeps all rights: ask danielvie before reusing the design.