Skip to the content
4 layers63.5 × 22.9 mmNuDAC, the printed circuit board in 3D

A USB sound card based on Nuvoton M482ZGCAE MCU and NAU88L25 I2S audio codec

Size
63.5 × 22.9 mm
Copper layers
4
Thickness
1.6 mm
Parts
62
Nets
63
Pads
257
Tracks, vias
544, 194
Pours
5
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
14 Aug 2021
Updated
2 Oct 2022

Overview

NuDAC is an open-source printed circuit board by danchouzhou, from the danchouzhou/NuDAC repository on GitHub, published under the MIT licence. It is a 4-layer board of 63.5 × 22.9 mm with 62 parts on 63 nets, routed with 544 tracks and 194 vias.

It is built around the M482ZGCAE, SN74LV1T34DCK and NAU88L25YGB, with the TPS2065CDBVR-2 among its other parts. Its parts include 28 capacitors, 11 resistors, 6 ICs, 4 connectors and 1 diode. It belongs with the audio and music boards of this library.

Main components

4

README

README.md

NuDAC

A USB codec based on Nuvoton M482ZGCAE MCU and NAU88L25YGB I2S audio codec image

Fetures

Design

  • Provide almost all of MCU I/O on pin header
  • Low noise & fail-safe power design
  • Four-layer PCB
  • Low profile mid mount THT phone jack
  • On board APA ELECTRONIC CO., LTD. patented RGB LED with level translator
  • Molex USB 2.0 through hole Type-C connector improve mechanical strength
  • Jump free Nu-Link connectivity
  • Support semi-auto USB ISP (by pressing reset button) provide firmware update and secondary development without a programmer

Nuvoton M482ZGCAE microcontroller

  • ARM Cortex-M4 processor up to 192MHz with float point unit and DSP
  • 16-channel programable peripheral direct memory access
  • USB 2.0 full-speed with precise internal oscillator
  • Rich interface include UART, SPI, IIC, IIS, LIN
  • 12-bit ADC and DAC
  • 16-bit PWM
  • True random number generator

Nuvoton NAU88L25YGB high performance audio codec

  • On chip ground referenced Class-A/AB/G selectable headphone amplifier
  • On chip DSP include DRC (Dynamic Range Compressor), and programmable biquad filters
  • 24-bit A/D and D/A signal processing unit, up to 192K sample rate
  • 124dB SNR (@ 1Vrms, 0dB gain, 1KHz)
  • THD+Noise -89dB (@ 32 ohm, 1KHz, 20mW)
  • 28mW output power (@ 32 ohm, 1% THD+N)

Specification

  • 5V power supply: 4.5~5.5V, 1A max
  • 5V output capacity: 1A max
  • VDD output capacity: 300mA max

To clone this project

This project work with M480BSP submodule from Nuvoton corporation. You need to initialize submodules by passing --recurse-submodules to the git clone command.

text
git clone https://github.com/danchouzhou/NuDAC --recurse-submodules

Prepare develop environment

  1. Installing tools
text
sudo apt install kicad build-essential gcc-arm-none-eabi libtool libusb-1.0-0-dev
  1. Build and install customize version of OpenOCD for Nuvoton devices
text
git clone https://github.com/OpenNuvoton/OpenOCD-Nuvoton.git
cd OpenOCD-Nuvoton
./bootstrap
./configure --enable-nulink
make
sudo make install

Parts

62
QtyValueFootprintReferences
82.2uFCapacitor_SMD:C_0603_1608MetricC3, C4, C9, C18, C19, C20, C21, C23
84.7uFCapacitor_SMD:C_0603_1608MetricC10, C11, C12, C13, C22, C24, C25, C26
6100nFCapacitor_SMD:C_0603_1608MetricC1, C6, C14, C15, C16, C17
6beadResistor_SMD:R_0603_1608MetricFB1, FB2, FB3, FB4, FB5, FB6
4MountingHoleMountingHole:MountingHole_2.7mm_M2.5_ISO7380H1, H2, H3, H4
2100KResistor_SMD:R_0603_1608MetricR5, R6
210uFCapacitor_SMD:C_0603_1608MetricC7, C8
21nFCapacitor_SMD:C_0603_1608MetricC27, C28
233RResistor_SMD:R_0603_1608MetricR3, R4
24K7Resistor_SMD:R_0603_1608MetricR7, R8
25K1Resistor_SMD:R_0603_1608MetricR1, R2
2Conn_01x14Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_VerticalJ2, J3
1100uFCapacitor_SMD:C_0603_1608MetricC2
110KResistor_SMD:R_0603_1608MetricR9
11MResistor_SMD:R_0603_1608MetricR11
11uFCapacitor_SMD:C_0603_1608MetricC5
121371600012137160001:2137160001J1
12SJ3080-000111F2SJ3080-000111F:2SJ3080-000111FCN1
168RResistor_SMD:R_0603_1608MetricR10
1APA-104-2020-5mAAPA-104-2020-5mA:APA-104-2020-5mAD1
1M482ZGCAEPackage_DFN_QFN:VQFN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mmU3
1MCP1812AT-018_OTPackage_TO_SOT_SMD:SOT-23-5U4
1MCP1812BT-033_OTPackage_TO_SOT_SMD:SOT-23-5U2
1NAU88L25YGBPackage_DFN_QFN:VQFN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mmU5
1PTS820PTS820:PTS820SW1
1SN74LV1T34DCKPackage_TO_SOT_SMD:SOT-353_SC-70-5U6
1SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1TPS2065CDBVR-2Package_TO_SOT_SMD:SOT-23-5U1

Similar boards

  • 6 layers254 × 115 mmHw openmower sabo, the printed circuit board in 3D

    Hw openmower sabo

    xtech/hw-openmower-sabo

    OpenMower is an open-source project that upgrades off-the-shelf robotic mowers into modern, smart lawn mowing robots with RTK GPS technology. For more details, check out the OpenMower project.

    356 parts5
  • 2 layers74.2 × 54.2 mmMsx joyduke v1, the printed circuit board in 3D

    Msx joyduke v1

    herraa1/msx-joyduke-v1

    Use original Xbox joysticks with your MSX computer

    54 parts1GPL-3.0
  • 4 layers100 × 49.8 mmCrossfire, the printed circuit board in 3D

    Crossfire

    lightsource-nz/crossfire_mk5

    crossfire: USB-MIDI forwarding agent for embedded USB-MIDI smart hubs

    110 parts1
  • 2 layers65 × 30 mmMax3421e rpi uhat, the printed circuit board in 3D

    Max3421e rpi uhat

    StarGate01/max3421e-rpi-uhat

    A uHAT for the Rapberry Pi (Zero), which adds a second USB 2.0 controller over SPI, using the MAX3421E chip.

    23 parts1MPL-2.0
  • 4 layers200 × 65 mmDD Compute 2, the printed circuit board in 3D

    DD Compute 2

    Acmex2564/Z31-DigiDash

    Reverse Engineering of the 300zx (Z31) Digital Cluster & Design of replacement PCBs

    183 parts19
  • 2 layers40 × 98 mmAirquality, the printed circuit board in 3D

    Airquality

    LukasLendvorsky/airquallity-esphome

    WIFI airquality sensor with ESP32

    59 parts3GPL-3.0
  • 6 layers34 × 40 mmESPWatchS3, the printed circuit board in 3D

    ESPWatchS3

    Ilikemining1/ESPWatchS3

    ESP32-S3 based smartwatch with CrystalFontz 240x240 1.3in LCD.

    126 parts2
  • 6 layers48.2 × 50 mmRFB, the printed circuit board in 3D

    RFB

    Penta0308/BikeRadar

    229 parts2

Questions

How big is the NuDAC PCB?

It measures 63.5 × 22.9 mm and has 4 copper layers, 1.6 mm thick.

What parts does the NuDAC use?

62 parts, built around the M482ZGCAE, SN74LV1T34DCK, NAU88L25YGB and TPS2065CDBVR-2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NuDAC KiCad files?

From the danchouzhou/NuDAC repository on GitHub, at the commit this page was made from: the board is kicad/NuDAC.kicad_pcb and its schematic kicad/Header/file608CB110.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the NuDAC design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).