4 layers91 × 53.1 mm
Nff pcb
o7-machinehum/flipper-blackhat
Linux based WiFi pentesting device for the Flipper Zero.
184 parts300
4 layers90.1 × 59.2 mm
Linux capable PCB KiCAD
damjanovgit/Linux-capable-PCBDizajn štampane pločice i board bring-up za Linux operativni sistem.
- Size
- 90.1 × 59.2 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 153
- Nets
- 255
- Pads
- 795
- Tracks, vias
- 20,239, 235
- Pours
- 43
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 6 May 2022
- Updated
- 30 Nov 2022
Overview
Linux capable PCB KiCAD is an open-source printed circuit board by damjanovgit, from the damjanovgit/Linux-capable-PCB repository on GitHub. It is a 4-layer board of 90.1 × 59.2 mm with 153 parts on 255 nets, routed with 20,239 tracks and 235 vias.
It is built around the A33, TPS62130RGT and AP131-25WG, with the RTL8188CUS-GR, CC0402KRX7R7BB104 and BC547 among its other parts. Its parts include 79 capacitors, 38 resistors, 9 ICs, 5 connectors and 4 inductors. It belongs with the computers and single-board computers boards of this library.
Main components
6
A33
TFBGA-282-20℃~+75℃ 32 Bit 6bit ARM Cortex-A7 Built-in+External External TFBGA-282 Microcontrollers (MCU/MPU/SOC) ROHSAllwinner TechMicrocontrollers (MCU/MPU/SOC)
TPS62130RGT
VQFN-16-EP(3x3)-40℃~+85℃@(TA) 1 17uA 2.5MHz 3A 3V~17V 900mV~6V Adjustable Buck Buck Built-in Yes QFN-16-EP(3x3) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AP131-25WG
SOT-25-40℃~+85℃@(Ta) 1 2.5V 300mA 400mV@(300mA) 5.5V 50uA 60dB@(100Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-25 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRTL8188CUS-GR
QFN-46_4.5X6.5QFN-46_4.5X6.5 New Arrivals ROHSRealtek SemiconUncategorised
CC0402KRX7R7BB104
0402100nF 16V X7R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMT
BC547
TO-92Bipolar (BJT)Jiangsu Changjing Electronics Technology (CJ)
README
README.mdLinux-capable-PCB
Dizajn štampane pločice i board bring-up za Linux operativni sistem.
Parts
153| Qty | Value | Footprint | References |
|---|---|---|---|
| 41 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C10, C11, C14, C15, C18, C20, C21, C22, C25, C33, C36, C40, C46 +25 |
| 17 | 22u | Capacitor_SMD:C_0603_1608Metric | C7, C13, C23, C24, C34, C68, C69, C76, C77, C79, C80, C83, C84, C87, C88, C89 +1 |
| 11 | 100k | Resistor_SMD:R_0603_1608Metric | R7, R11, R12, R14, R15, R16, R18, R22, R23, R31, R32 |
| 6 | 0R | Resistor_SMD:R_0603_1608Metric | R6, R28, R29, R30, R37, R38 |
| 6 | 10u | Capacitor_SMD:C_0603_1608Metric | C17, C35, C38, C39, C74, C78 |
| 4 | 1u | Inductor_SMD:L_0603_1608Metric | L2, L3, L4, L5 |
| 4 | ??? | Capacitor_SMD:C_0603_1608Metric | C70, C71, C85, C86 |
| 4 | Mounting_Hole | MountingHole:MountingHole_3mm | MK1, MK2, MK3, MK4 |
| 4 | TPS62130 | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm | U9, U10, U12, U13 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric | C31, C32 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 1k 1% | Resistor_SMD:R_0603_1608Metric | R20, R21 |
| 2 | 22R | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 240R | Resistor_SMD:R_0603_1608Metric | R5, R19 |
| 2 | 30p | Capacitor_SMD:C_0603_1608Metric | C29, C30 |
| 2 | C | Capacitor_SMD:C_0603_1608Metric | C26, C28 |
| 2 | R | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | Test_Point | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP8 |
| 1 | 100nF | Resistor_SMD:R_0603_1608Metric | C26 |
| 1 | 100u | Capacitor_SMD:C_0603_1608Metric | C72 |
| 1 | 10M | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 110k | Resistor_SMD:R_0603_1608Metric | R35 |
| 1 | 120k | Resistor_SMD:R_0603_1608Metric | R27 |
| 1 | 150k | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 160k | Resistor_SMD:R_0603_1608Metric | R36 |
| 1 | 1V1 TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP6 |
| 1 | 1V35 TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP7 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C37 |
| 1 | 200k | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | 220k | Resistor_SMD:R_0603_1608Metric | R34 |
| 1 | 22uF | Resistor_SMD:R_0603_1608Metric | C27 |
| 1 | 24MHz | Crystal:Crystal_SMD_EuroQuartz_MJ-4Pin_5.0x3.2mm | Y1 |
| 1 | 26 MHz | Crystal:Crystal_SMD_EuroQuartz_MJ-4Pin_5.0x3.2mm | Y3 |
| 1 | 2V5 TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP3 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_EuroQuartz_MJ-4Pin_5.0x3.2mm | Y2 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric | R26 |
| 1 | 3V0 TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP5 |
| 1 | 3V3 TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP4 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R24 |
| 1 | 470u | Capacitor_SMD:C_0603_1608Metric | C73 |
| 1 | 5V TP | TestPoint:TestPoint_Pad_1.0x1.0mm | TP2 |
| 1 | 82k | Resistor_SMD:R_0603_1608Metric | R33 |
| 1 | A33 | eec:Allwinner_Technology_Co.,_Ltd.-A33-0 | U1 |
| 1 | AP131-25 | Package_TO_SOT_SMD:SOT-23-5 | U11 |
| 1 | Antenna_Dipole | Small2_4GHz_PCB_Antenna:Small2_4GHz_PCB_Antenna | AE1 |
| 1 | BC547 | Package_TO_SOT_SMD:SC-59_Handsoldering | Q2 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_CUI_PJ-063AH_Horizontal | J7 |
| 1 | GPIO_CONN | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J2 |
| 1 | HTQ4G63AFR-PCB | Package_BGA:BGA-96_9.0x13.0mm_Layout2x3x16_P0.8mm | U8 |
| 1 | MIC_DIFF_IN | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J6 |
| 1 | Q_PMOS_GSD | Package_TO_SOT_SMD:SC-59_Handsoldering | Q1 |
| 1 | RTL8188CUS | realtek:RTL8188CUS | U2 |
| 1 | SD_card_slot | SD_Card_9_pin:SD_Card_9_pin_slot | U5 |
| 1 | UART_CONN | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | USB_A | Connector_USB:USB_Micro-B_Molex-105017-0001 | J4 |
Questions
How big is the Linux capable PCB KiCAD PCB?
It measures 90.1 × 59.2 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Linux capable PCB KiCAD use?
153 parts, built around the A33, TPS62130RGT, AP131-25WG and RTL8188CUS-GR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Linux capable PCB KiCAD KiCad files?
From the damjanovgit/Linux-capable-PCB repository on GitHub, at the commit this page was made from: the board is Linux-capable-PCB-KiCAD/Linux-capable-PCB-KiCAD.kicad_pcb and its schematic Linux-capable-PCB-KiCAD/A33_GPIO.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Linux capable PCB KiCAD design in my own project?
Its repository states no licence, so its author keeps all rights: ask damjanovgit before reusing the design.
Similar boards
- 4 layers59 × 53 mm
Nff pcb
o7-machinehum/wifiwart
Linux SBC featuring two wifi radios, masquerading as a USB charger.
145 parts184MIT - 4 layers66 × 55 mm
- 4 layers80 × 42 mm
Module
vd-rd/sbc_allwinner_a13
Open hardware compute module with Allwinner A13 (ARM-A8 @1GHz), DDR3 (max 512MB) and expansions (USB, GPIO, WiFi, LCD, Audio)
179 parts38 - 4 layers66 × 42 mm
Sbc
vd-rd/sbc_at91sam9g10
Open hardware SBC module based on AT91SAM9G10 @266MHz with max 128MB RAM
118 parts2 - 4 layers66 × 42 mm
Sbc
vd-rd/sbc_at91sam9g20
Open hardware SBC module based on AT91SAM9G20 @400MHz with 128MB RAM
116 parts2 - 4 layers74.5 × 70.3 mm
Nest mini v2-drop in pcb
iMike78/nest-mini-drop-in-pcb
Drop-in PCB replacement for the Google Nest Mini v2 with ESP32-S3, ESP32-P4 and optional ESP32-C6. Inspired by Onju Voice and Home Assistant Voice PE.
229 parts628CERN-OHL-S-2.0 - 4 layers74.5 × 70.3 mm
Nest mini v2-drop in pcb
marceldale/nest-mini-v2-voice
Open voice satellite board for the Google Nest Mini (2nd gen): local Home Assistant voice assistant with ESP32-S3 + XMOS XU316, ESPHome, Voice PE compatible. Open hardware, prototype stage.
249 parts4CERN-OHL-S-2.0