

NES MEP
Multipurpose Expansion Port (MEP) Surface Mount Device (SMD) Hardware for OSGP Smart Meters in Denmark
- Size
- 70 × 28 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 56
- Pads
- 103
- Tracks, vias
- 205, 46
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Jul 2022
- Updated
- 12 Mar 2024
Overview
NES MEP is an open-source printed circuit board by DabblerDK, from the DabblerDK/MEP-HW-SMD repository on GitHub. It is a 2-layer board of 70 × 28 mm with 24 parts on 56 nets, routed with 205 tracks and 46 vias.
It is built around the ESP32-WROOM-32 and MAX3232ID. Its parts include 7 resistors, 7 connectors, 5 capacitors, 2 ICs and 1 diode. It belongs with the retro computing and games boards and the ESP32 boards of this library.
Main components
2ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMAX3232ID
SOIC-16-40℃~+85℃ 2 2 250Kbps 300uA 3V~5.5V Short-Circuit Protection Transceiver Yes ±15kV SOIC-16 RS232 ICs ROHSTexas InstrumentsRS232 ICs
README
README.mdMEP-HW-SMD v2.00
Multipurpose Expansion Port (MEP) Surface Mount Device (SMD) Hardware for OSGP Smart Meters in Denmark
This hardware will not be updated any further as I no longer have access to a NES Smart Meter. Read more here: https://www.dabbler.dk/index.php/2023/10/31/echelon-nes-smart-meters-probably-our-final-post-on-this-topic/
This is the repository holding the Surface Mount Device (SMD) Hardware for OSGP Smart Meters (i.e. Echelon or NES) in Denmark. The scematics can be use in other countries too if you gain access to the Multipurpose Expansion Port (MEP) terminals. Please:
- see https://github.com/OSGP-Alliance-MEP-and-Optical for further hardware specifiactions of these meters.
- see https://www.dabbler.dk for further information about this hardware project
Version 1.10 is THT and version 2.00 is SMD. The two versions share schematics and are 100% compatible. They uses the same software and have the exact same functionality - only the component technology has changed.
Notes:
- The Gerber files has been generated acording to JLCPCBs specifications.
- We have not been able to source the correct MEP connector, so please note that the pin-numbers does NOT corespond to the pin numbers in the official documentation. Also you should NOT insert the 2x3 pin headers all the way into the PCB (the pins should be aligned with the PCB back side).
- The ESP32 can be programmed "on board" using the J5 connector. We usually don't put headers on that one, but simply insert the pins of a FTDI232 directly into the holes. WARNING: Some FTDI232's supply 5v EVEN when they are jumped to 3.3v. Don't use those - they'll fry your ESP32!
- Debug information from the software are written on the serial out on J5. Remember it is 3.3v and if you use a FTDI232, please only connect GND, TXD and RXD during normal operation (i.e. when the module is connected to a meter)
- The Schematic for the THT and the SMD versions are currently the same, but they might branch in the future
- J7 have two functions: before "on board" programming of the ESP32 a jumper must be set between ESP_PROGRAM and GND (pin 1 and 2) and the power jumper between pin 3 and 4 must be removed
- WARNING: Remove all jumpers from J7 before adjusting the buck converter voltage to 3.4v-3.5v. When done set a jumper between pin 3 and 4 for nomal operation.
- The buck converter must be mounted without pin headers, i.e. flush to the PCB. Just put solder blobs in the holes and use additional heat for a good connection. The module will not fit in the meter if pin headers are used!
Bill of Materials:
| Component | Value | Type | Note |
|---|---|---|---|
| R1-R2 | 10K ohm | 0805 | |
| R3-R7 | 0 ohm | 0805 | Mount either R3 (permanent) or R4 (ESP32 controlled, recommended) depending on how you will power your MAX3232. See https://www.dabbler.dk/index.php/2022/04/03/echelon-nes-smart-meters-dabbling-the-hardware-v1-10-and-v2-00/ |
| D1 | 1N4007 | 0805 | The line on the diode should be towards the D1 markings on the PCB silk screen |
| C1-C5 | 100nF | 0805, Non-polarized | i.e. https://www.ebay.com/itm/255486850064 |
| U1 | MAX3232 | SOIC-16 | 3.3v version, i.e. https://www.ebay.com/itm/291205964463 |
| U2 | ESP32-wroom-32e | 16MB recommended but currently NOT required | We have not experienced any thermal issues so we do not solder the middle thermal pad. Just make sure the ESP32 is flush with the PCB |
| J1-J4 | DC-DC Buck converter | i.e. https://www.ebay.com/itm/264731212329. The VIN- corner should be aligned towards the 5 capacitors C1-C5 | |
| J6 | 2x3 Horizontal pin header | THT 2.54mm | IMPORTANT: Do not insert this pin header fully in the PCB. The pins should be soldered exactly flush with the PCB surface on the soldering side of the PCB to fit the connector in the meter! i.e. https://www.ebay.com/itm/253023279430. 2024-03-12 A better option is to use the correct connector - you will find it on AliExpress here https://www.aliexpress.com/item/1005002409430150.html |
| J7 | 2x2 Vertical pin header | SMD 1.27mm | i.e. https://www.ebay.com/itm/173851525492. You will need one jumper for these: If set between the two pins next to the ESP32 it is in programming mode (use FTDI232 board connected to J5 to program). If set between the two pins next to the J6 MEP connector it is in normal operation. Remove jumper completely while adjusting the Buck converter (no power will then be supplied to chips) |
Pictures of the populated PCB:

Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R4, R5, R6, R7 |
| 5 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C5 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2 |
| 1 | Connector_PinHeader_1.27mm:PinHeader_2x02_P1.27mm_Vertical_SMD | J7 | |
| 1 | 1N4007 | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | Buck +24v input | TestPoint:TestPoint_Pad_4.0x4.0mm | J2 |
| 1 | Buck +3v3 output (see note) | TestPoint:TestPoint_Pad_4.0x4.0mm | J4 |
| 1 | Buck GND input | TestPoint:TestPoint_Pad_4.0x4.0mm | J1 |
| 1 | Buck GND output | TestPoint:TestPoint_Pad_4.0x4.0mm | J3 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U2 |
| 1 | MAX3232 | Package_SO:SOIC-16_4.55x10.3mm_P1.27mm | U1 |
| 1 | NES Meter MEP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Horizontal | J6 |
| 1 | Prog/debug | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
The 22 most common of 24 parts.
Similar boards
- 2 layers42.8 × 53 mm

- 4 layers50 × 50 mm

ESP32-Sentinel Kinetic Wireless Dongle
alextrical/ESP32-Sentinel-Kinetic-Wireless-Dongle
ESP8266 based Re-implementation of the Vent-Axia Sentinel Kinetic Wired Remote Controller without a Display
81 parts6CERN-OHL-S-2.0 - 2 layers70 × 28 mm

NES MEP
DabblerDK/MEP-HW-THT
Multipurpose Expansion Port (MEP) Through-Hole Technology (THT) Hardware for OSGP Smart Meters in Denmark
24 parts3 - 2 layers137.5 × 51 mm

- 2 layers63.8 × 52.7 mm

Projeto SIllion
Henriquepr15/ESP32-Motor-RS232
Projeto de hardware com ESP32, RS232 e controle de motor
59 parts - 2 layers92 × 70 mm

- 4 layers70 × 157.5 mm

Controller Tv Lift
vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.
103 parts - 2 layers189.5 × 204.9 mm

SmartSpin2k Panelized
doudar/SmartSpin2k
Transform your spin bike into a Smart Trainer!
749 parts292GPL-2.0
Questions
How big is the NES MEP PCB?
It measures 70 × 28 mm and has 2 copper layers, 1.6 mm thick.
What parts does the NES MEP use?
24 parts, built around the ESP32-WROOM-32 and MAX3232ID. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the NES MEP KiCad files?
From the DabblerDK/MEP-HW-SMD repository on GitHub, at the commit this page was made from: the board is NES-MEP.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the NES MEP design in my own project?
Its repository states no licence, so its author keeps all rights: ask DabblerDK before reusing the design.