2 layers52.6 × 48.8 mm
2 layers39.5 × 94 mm
Marker
Cyclic007/markerThis is a RP2040 dev-bord that has wireless capabilities
- Size
- 39.5 × 94 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 88
- Pads
- 438
- Tracks, vias
- 709, 71
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Nov 2025
- Updated
- 21 Nov 2025
Overview
Marker is an open-source printed circuit board by Cyclic007, from the Cyclic007/marker repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 39.5 × 94 mm with 57 parts on 88 nets, routed with 709 tracks and 71 vias.
It is built around the RP2040, DWM1001C and W25Q128JVSIQ. Its parts include 15 capacitors, 7 resistors, 3 ICs and 1 connector. It belongs with the RP2040 boards of this library.
Main components
3
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
DWM1001C
SMDIntegrated temperature sensor、Integrated antenna SMD RF Modules ROHSDecaWaveRF Modules
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
README
README.mdThis is a RP2040 dev-bord that has wireless capabilities
It uses a DWM1001 for wireless and has a USB-C port for interface
I can't get the PCB made any closer and I need to use JLC PCB
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | MountingHole_Pad | MountingHole:MountingHole_2.5mm_Pad_Via | H1, H2, H10, H11, H12, H13, H14, H15, H16, H17, H18, H19, H20, H21, H22, H23 +12 |
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C3, C4, C6, C8, C10, C11, C12, C13, C14, C15 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C5, C7 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 1 | 1.7 | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 2.2 | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 2216100001 | Connector_USB:MOLEX_2216100001 | J1 |
| 1 | Crystal_GND24 | Oscillator:XTAL_ABM8-272-T3 | YABM8-272-T1 |
| 1 | DWM1001 | RF_Module:DecaWave_DWM1001 | U3 |
| 1 | LOGO | LOGO | G*** |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | Switch | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC6xxG | SWBOOT1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
Questions
How big is the Marker PCB?
It measures 39.5 × 94 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Marker use?
57 parts, built around the RP2040, DWM1001C and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Marker KiCad files?
From the Cyclic007/marker repository on GitHub, at the commit this page was made from: the board is PCB/marker.kicad_pcb and its schematic PCB/marker.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Marker design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers59 × 50 mm
XlAnchor
ClemensElflein/xLocalization
The xLocalization project aims to provide a simple to use, low cost indoor positioning system for hobbyist use.
34 parts1 - 2 layers59.7 × 64.8 mm
- 2 layers42 × 67 mm
- 2 layers181 × 97 mm
OpenDeck r3.1.2
shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.
262 parts960Apache-2.0 - 4 layers82.6 × 82.5 mm
- 4 layers102.9 × 96.7 mm
PicoGUS chipdown
polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support
99 parts805 - 4 layers180.8 × 300.3 mm
Dilemma
Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.
383 parts590