2 layers100 × 100 mm
I n c u r
cyberboy666/i_n_c_u_r
a r_e_c_u_r video sampler extension circuit - adding knobs, cv and serial midi control
38 parts16GPL-3.0
2 layers100 × 100 mm
RecurBOY
cyberboy666/recurBOY122a rpi0 video-instrument – created in collaboration with Guergana Tzatchkova
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 61
- Pads
- 189
- Tracks, vias
- 481, 5
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 10 Jul 2019
- Updated
- 28 Sep 2026
Overview
RecurBOY is an open-source printed circuit board by cyberboy666, from the cyberboy666/recurBOY repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 100 × 100 mm with 35 parts on 61 nets, routed with 481 tracks and 5 vias.
It is built around the MCP3008-I/P and BAT46. Its parts include 10 connectors, 8 diodes, 5 switches, 4 resistors and 1 capacitor.
Main components
2README
panel/default_panel/readme.mdrecurboy default_panel notes
- the mounting holes fit m3 screws
- the front_panel mounts to pcb with 10mm standoffs
- 35mm screws will fit top of front_panel, pcb and support pi0 at angle pi0 - 15mm screws should fit bottom
- the default potentiometers in underscores BOMs have 12mm shaft lengths - consider replacing these with >17mm shaft length alternatives if you plan to use it with a panel
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | bat46 | lib_fp:D_DO-35_SOD27_P5.08mm_Vertical_KathodeUp | D1, D2, D3, D4, D5, D6, D7, D8 |
| 5 | push | Button_Switch_THT:SW_PUSH-12mm | SW1, SW2, SW3, SW4, SW5 |
| 4 | 10k_pot | lib_fp:Potentiometer_Alps_RK09K_Single_Vertical | RV1, RV2, RV3, RV4 |
| 4 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4 |
| 4 | mono_jack_3.5mm | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J1, J2, J3, J4 |
| 2 | LOGO | custom_new:logo | G***, G*** |
| 1 | 0.1u | Capacitor_THT:C_Disc_D7.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 2x20_Socket | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J8 |
| 1 | Pin_Socket | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | display_1.8 | lib_fp:tht_1.8_inch_tft_display | J5 |
| 1 | europower | Connector_IDC:IDC-Header_2x08_P2.54mm_Vertical | J10 |
| 1 | mcp3008 | lib_fp:DIP+SOIC-16 | U1 |
| 1 | push_5way | lib_fp:tht_sw_5way | J9 |
| 1 | rca | lib_fp:tht_vertical_rca | J7 |
Similar boards
- 2 layers100 × 100 mm
Sync ope
cyberboy666/sync_ope
effect send + sync restoring circuit - adapted from a gael jaton design
78 parts52 - 2 layers148.8 × 132.2 mm
Usbflashprog
robsonsmartins/usbflashprog
A memory device programmer (Flash/EPROM/E2PROM) board and software, connected to PC by USB port.
125 parts36 - 2 layers74 × 34 mm
EMS Bus Gateway
mariusgreuel/EMS-Bus-Gateway
EMS Bus Gateway for Buderus Boilers to run EMS-ESP32
48 parts21GPL-3.0 - 4 layers128 × 184 mm
Cosmicpi 1.7
CosmicPi/CosmicPiV1.7PCB
PCB for Version 1.7 of the Cosmic Pi Hardware. Incremental changes from V1.6. This design is licensed under the CERN OHL V1.2
219 parts14 - 2 layers38.1 × 109.2 mm
- 2 layers78 × 79 mm
- 2 layers58.8 × 60.2 mm
Questions
How big is the RecurBOY PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RecurBOY use?
35 parts, built around the MCP3008-I/P and BAT46. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RecurBOY KiCad files?
From the cyberboy666/recurBOY repository on GitHub, at the commit this page was made from: the board is hardware/recurBOY.kicad_pcb and its schematic hardware/recurBOY.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RecurBOY design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).