Skip to the content
2 layers49 × 19 mmCh32-linke, the printed circuit board in 3D

Ch32-linke

cyao1234/linke

Clone of the LinkE programmer that can do single-wire SWO and DSP

Size
49 × 19 mm
Copper layers
2
Thickness
1.6 mm
Parts
36
Nets
36
Pads
122
Tracks, vias
300, 71
Pours
3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
21 May 2026
Updated
9 Jul 2026

Overview

Ch32-linke is an open-source printed circuit board by cyao1234, from the cyao1234/linke repository on GitHub. It is a 2-layer board of 49 × 19 mm with 36 parts on 36 nets, routed with 300 tracks and 71 vias.

It is built around the TPS2552DBVR-1. Its parts include 14 resistors, 5 capacitors, 4 ICs, 2 diodes and 2 connectors. It belongs with the RISC-V boards of this library.

Main components

1

README

README.md

LinkE clone

Clone of the LinkE programmer that can do single-wire SWO and DSP

Used for programming a wide variety of low-cost mcus

Features are:

  • Cheap cost
  • Firmware compatibility
  • USB programming module with pogo-pins
  • Handheld
  • Single sided

Usage: Just plug in the USB! As simple as that. Compatible with minichlink

Bom: PCB + PCBA: ~56.12

Parts

36
QtyValueFootprintReferences
4100RResistor_SMD:R_0603_1608MetricR5, R6, R9, R10
31kResistor_SMD:R_0603_1608MetricR11, R13, R14
2100kResistor_SMD:R_0603_1608MetricR3, R4
21uFCapacitor_SMD:C_0603_1608MetricC2, C3
2270RResistor_SMD:R_0603_1608MetricR7, R8
233pFCapacitor_SMD:C_0603_1608MetricC4, C5
25.1kResistor_SMD:R_0603_1608MetricR1, R2
2LEDLED_SMD:LED_0603_1608MetricD1, D2
2SW_PushButton_Switch_SMD:SW_SPST_TS-1088-xR020SW1, SW2
2TPS2552DBVRPackage_TO_SOT_SMD:SOT-23-6U5, U6
1100nFCapacitor_SMD:C_0603_1608MetricC1
110kResistor_SMD:R_0603_1608MetricR12
112MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1CH32V30xFxPxPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU1
1Conn_02x05_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ2
1GNDlinke:TestPoint_Pad_D2.5mmTP5
1SWCLKlinke:TestPoint_Pad_D2.5mmTP3
1SWDIOlinke:TestPoint_Pad_D2.5mmTP4
1TestPointTestPoint:TestPoint_Pad_D1.0mmTP1
1USB_C_Receptacle_USB2.0_14PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1
1VBUSlinke:TestPoint_Pad_D2.5mmTP2
1XC6206PxxxMRPackage_TO_SOT_SMD:SOT-23-3U2

The 35 most common of 36 parts.

Similar boards

  • 2 layers120.4 × 100.4 mmRelaymux, the printed circuit board in 3D

    Relaymux

    PetteriAimonen/relaymux

    Hardware and firmware for a USB connected relay box

    59 parts18BSD-2-Clause
  • 2 layers36 × 66.5 mmUSB HUB, the printed circuit board in 3D

    USB HUB

    RatnakarSahooVSSUT/4-Port-USB-2.0-Hub

    Custom 4-port USB 2.0 hub PCB designed in KiCad, featuring a GL852G controller, USB-C and USB-A interfaces.

    34 parts1
  • 4 layers70 × 30 mmUsb replug, the printed circuit board in 3D

    Usb replug

    clankagent/usb-replug

    USB 2.0 timed disconnect adapter with CMOS 555; revision B unbuilt prototype for design review

    40 parts
  • 4 layers72.7 × 88.7 mmOptimus Hub, the printed circuit board in 3D

    Optimus Hub

    devisunofficial/Optimus-Hub

    Optimus hub is a USB 2.0 hub which has USB Type-C upstream port and 6 downstream USB Type-A port and one TF-Card reader

    76 parts
  • 4 layers49.5 × 21.6 mmUSB Replug Dongle RevC1, the printed circuit board in 3D

    USB Replug Dongle RevC1

    gslee-dev/portpulse

    USB replug test dongle with KiCad hardware, CH552 firmware, and native C host

    38 partsMIT
  • 4 layers8.8 × 62.9 mmController, the printed circuit board in 3D

    Controller

    Takazudo/zudo-led-block

    led block module

    66 parts
  • 2 layers96.1 × 29.3 mmUSB A Daughterboard, the printed circuit board in 3D

    USB A Daughterboard

    nearestexit/mx-unsaver

    Custom Keyboard & Numpad inspired by the IBM "Unsaver", designed with Onshape and KiCad

    57 parts40MIT
  • 2 layers65 × 30 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    36 parts1kGPL-3.0

Questions

How big is the Ch32-linke PCB?

It measures 49 × 19 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ch32-linke use?

36 parts, built around the TPS2552DBVR-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ch32-linke KiCad files?

From the cyao1234/linke repository on GitHub, at the commit this page was made from: the board is hardware/ch32-linke.kicad_pcb and its schematic hardware/ch32-linke.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ch32-linke design in my own project?

Its repository states no licence, so its author keeps all rights: ask cyao1234 before reusing the design.