
Zero crossing detector
cs2dsb/zcssr
A PCB and software for a SSR controller that monitors mains AC zero crossings to determine when to turn the SSR on.

A dev board designed to facilitate the development of USB firmware for STM32
Usb dev board is an open-source printed circuit board by cs2dsb, from the cs2dsb/stm32-usb.rs repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 46.8 × 52 mm with 57 parts on 84 nets, routed with 411 tracks and 62 vias.
It is built around the FT231XS-R, AP2112K-3.3 and USBLC6-2SC6, with the B5819W among its other parts. Its parts include 19 capacitors, 15 resistors, 6 diodes, 5 connectors and 4 ICs. It belongs with the microcontroller boards boards and the STM32 boards of this library.
Experimental UF2 bootloader written in rust.
Ignore the hardware folder - the PCB may work but I didn't bother getting it manufactured in the end as the bluepill was sufficient for my needs.
Check out the firmware/usb_bootloader folder for more info.
Free and open source software distributed under the terms of both the MIT License and the Apache License 2.0.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100nf | Capacitor_SMD:C_0402_1005Metric | C1, C5, C8, C9, C10, C11, C12, C15, C19 |
| 5 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R4, R11, R13, R15 |
| 4 | 22 | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8 |
| 4 | MountingHole | MountingHole:MountingHole_4.3mm_M4 | H1, H2, H3, H4 |
| 2 | 100k | Resistor_SMD:R_0402_1005Metric | R9, R14 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R10, R12 |
| 2 | 10nf | Capacitor_SMD:C_0402_1005Metric | C2, C14 |
| 2 | 10uf | Capacitor_SMD:C_0402_1005Metric | C4, C13 |
| 2 | 22pf | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 2 | 47pf | Capacitor_SMD:C_0402_1005Metric | C17, C18 |
| 2 | B5819W | Diode_SMD:D_SOD-123 | D5, D6 |
| 1 | 100ohm | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | 1uf | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 220 | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 2k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 4.7uf | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | BOOT0 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | BOOT1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_01x12 | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J1 |
| 1 | FT231XS | Package_SO:SSOP-20_3.9x8.7mm_P0.635mm | U5 |
| 1 | FTDI_USB | Custom:USB_MICRO_B_U-F-M5DD-W-2 | J3 |
| 1 | PWR_Green | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | RX_Yel | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_B3SL-1002P | SW1 |
| 1 | STM32F103RCTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | STM_USB | Custom:USB_MICRO_B_U-F-M5DD-W-2 | J2 |
| 1 | TX_Yel | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USR_Red | LED_SMD:LED_0603_1608Metric | D2 |
The 56 most common of 57 parts.

cs2dsb/zcssr
A PCB and software for a SSR controller that monitors mains AC zero crossings to determine when to turn the SSR on.

Woz4tetra/auto-battlebot
This project brings aim-assist and autonomous control to combat robots.

anhldptit2610/dalws
This project is my attempt to learn about microcontroller and PCB design. Now I realize that making a full, complete electronic project is super hard.

makeristic/Feather_STM32WB55
KiCad STM32WB55 Bluetooth development board in the Adafruit Feather form factor, with USB-C and STEMMA QT. Work in progress.

0x0c/spltnrskb
KLE レイアウト(kle/left.json、kle/right.json)から生成した、左右分割・有線接続のキーボード基板です。 KiCad 10 のプロジェクト(回路図と配線済み基板)、製造用ガーバー、BOM、QMK ファームウェア設定を含みます。筐体のデータ(アクリルのレーザーカット用 DXF/SVG と 3D プリント用 STL)も入っています。

ajisrawi/DroneMagNav2.0
DroneMagNav 2.0 - survey-fluxgate magnetic-anomaly navigation board for drones (IGRF-14 + EMAG2v3 continued to flight altitude)

DesignStraub/ringwheel-hybrid-drone
A 5-inch FPV drone whose prop ducts fold down and become wheels. Design study in Fusion 360 and KiCad, CC BY-NC-SA 4.0.

ismailcelik-tr/quake-sensor
ADXL355 + ESP32-S3 home seismograph — KiCad 10, 2-layer, script-generated schematic and PCB
It measures 46.8 × 52 mm and has 2 copper layers, 1.6 mm thick.
57 parts, built around the FT231XS-R, AP2112K-3.3, USBLC6-2SC6 and B5819W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the cs2dsb/stm32-usb.rs repository on GitHub, at the commit this page was made from: the board is hardware/usb_dev_board/usb_dev_board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).