

Input Pico
Open source FPP PB16 Pixel Controller
- Size
- 71.9 × 60.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 47
- Nets
- 60
- Pads
- 203
- Tracks, vias
- 318, 31
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Aug 2019
- Updated
- 5 Oct 2026
Overview
Input Pico is an open-source printed circuit board by computergeek1507, from the computergeek1507/PB_16 repository on GitHub. It is a 2-layer board of 71.9 × 60.5 mm with 47 parts on 60 nets, routed with 318 tracks and 31 vias.
It is built around the L7805, RC0603FR-071KL and RMCF0603FT220R, with the B5819W-TP, 150080RS75000 and PPTC041LFBN-RC among its other parts. Its parts include 14 resistors, 9 diodes, 8 ICs, 5 connectors and 3 capacitors. It belongs with the RP2040 boards of this library.
Main components
7L7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsRC0603FR-071KL
UncategorisedUnknown makerRMCF0603FT220R
0603-55℃~+155℃ 100mW 220Ω 75V Thick Film Resistor ±1% ±100ppm/℃ 0603 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface MountB5819W-TP
SOD-123-65℃~+125℃ 1 Independent 10A 1A 1mA@40V 40V 600mV@1A SOD-123 Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes150080RS75000
0805-40℃~+85℃ 140° 150mcd 20mA 2V 625nm 630nm Discrete Diode Red Water Clear 0805 LED Indication - Discrete ROHSWürth ElektronikLight Emitting Diodes (LED)PPTC041LFBN-RC
插件,P=2.54mm-40℃~+105℃ 1 1x4P 2.54mm 250V 3A 4P 8.51mm Phosphor bronze Square Hole Through Hole Tin Top Plugin,P=2.54mm Female Headers ROHSSullins Connector SolutionsFemale Headers4DB-P108-02
插件,P=8.26mm1 150V 1x2P 2 2-Side 20A 2P 8.26mm Black Side Mount Straight Plugin,P=8.26mm Barrier Terminal Blocks ROHSTE ConnectivityBarrier Terminal Blocks
README
PB16_2_PI/README.mdCopyright and Disclaimer
Copyright: Scott Hanson
This documentation describes Open Hardware and is licensed under the CERN OHL v. 1.2.
You may redistribute and modify this documentation under the terms of the CERN OHL v.1.2. (http://ohwr.org/cernohl). This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN OHL v.1.2 for applicable conditions
PB16-2-PI
This is an adapter to use a Raspberry Pi W with the PB16 Cape instead of a PocketBeagle. This only supports the 16 local ports and the serial ports. The Expansion header does not work. Open source applications were used to create this PCB. KiCad was used for the PCB design, and LibreOffice for the documentation.
To order your own PCB upload the gerber.zip file to your favorite PCB manufacture of choice, I personally use jlcpcb.com.

Parts
47| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 2K | Resistor_SMD:R_0603_1608Metric | R1, R3, R4, R5, R6, R7, R8 |
| 7 | 330 | Resistor_SMD:R_0603_1608Metric | R2, R9, R10, R11, R12, R13, R14 |
| 6 | LED_Small | LED_SMD:LED_0603_1608Metric | D5, D6, D7, D8, D9, D10 |
| 6 | PC817 | Package_DIP:DIP-4_W7.62mm | U4, U5, U6, U7, U8, U9 |
| 4 | MountingHole | MountingHole:MountingHole_3.7mm | H1, H2, H3, H4 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D1 |
| 1 | BTN_JMP | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | Button_Fuse | Fuse:Fuse_0805_2012Metric | F5 |
| 1 | Buttons | Connector_Phoenix_MC_HighVoltage:PhoenixContact_MCV_1,5_8-G-5.08_1x08_P5.08mm_Vertical | J5 |
| 1 | L7805 | Package_TO_SOT_SMD:TO-252-2 | U3 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | LOGO | Scotts:chewi_15 | G*** |
| 1 | OLED | OLED-SSD1306-128X64-I2C:OLED-SSD1306-128X64-I2C-THT | J3 |
| 1 | Pico | MCU_RaspberryPi_and_Boards:RPi_Pico_W5500_SMD_TH | U1 |
| 1 | Power In | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | TB1 |
| 1 | RF | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J4 |
| 1 | RUN | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | VIN LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | VIN_JMP | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
More from computergeek1507/PB_16
12- 2 layers142.1 × 106 mm

- 2 layers148.8 × 116.9 mm

- 2 layers142.1 × 99.9 mm

- 2 layers148.8 × 116.9 mm

- 2 layers142.1 × 93 mm

- 2 layers151.1 × 93.4 mm

- 2 layers148.1 × 102.6 mm

- 2 layers148.6 × 76.4 mm

- 2 layers83.2 × 71.4 mm

- 2 layers100 × 90.4 mm

- 2 layers148.6 × 75.5 mm

- 2 layers90.1 × 71.4 mm

Similar boards
- 2 layers59.3 × 71.4 mm

- 2 layers63.4 × 85 mm

- 2 layers68.6 × 53.3 mm

Mie1001 daq simple
Chaospossum/mie1001-daq
MIE1001 Team 5: DAQ firmware and Arduino shield designs (preamp, ADS1115, MCP4725)
35 parts - 2 layers60 × 40 mm

Canary
offgridevices/offgrid-hardware
Open hardware from OffGrid Devices. One folder per board. CERN-OHL-S.
52 partsCERN-OHL-S-2.0 - 4 layers100 × 100 mm

- 2 layers35 × 62 mm

- 2 layers100 × 81.3 mm

- 2 layers53.5 × 26.5 mm

Questions
How big is the Input Pico PCB?
It measures 71.9 × 60.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Input Pico use?
47 parts, built around the L7805, RC0603FR-071KL, RMCF0603FT220R and B5819W-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Input Pico KiCad files?
From the computergeek1507/PB_16 repository on GitHub, at the commit this page was made from: the board is Input_Pico_SMD/Input_Pico.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Input Pico design in my own project?
Its repository states no licence, so its author keeps all rights: ask computergeek1507 before reusing the design.