

MAXPOWER
Hacemos roboces tope tochos
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 115
- Nets
- 199
- Pads
- 646
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Dec 2018
- Updated
- 20 Jul 2023
Overview
MAXPOWER is an open-source printed circuit board by Complubot, from the Complubot/AZ5 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 115 parts on 199 nets.
It is built around the ATMEGA2560-16AU, LM2907 and 74LS247P-E, with the HEF4040BT, L7805 and WS2812B among its other parts. Its parts include 36 capacitors, 25 resistors, 23 diodes, 13 ICs and 7 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATMEGA2560-16AU
TQFP-100(14x14)-40℃~+85℃ 10bit 16MHz 256KB 4.5V~5.5V 4KB 8 Bit 86 8KB AVR Built-in FLASH TQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM2907
DIP-14DIP-14 V/F and F/V Converters ROHSGcoreUncategorised74LS247P-E
-- Interface - Specialized ROHSRenesas ElectronicsInterface - SpecializedHEF4040BT
SOIC-16-40℃~+85℃ 1 12 35ns 4.5V~15.5V 50MHz Asynchronous Divide-by-2 Falling Edge SOIC-16 Counters, Dividers ROHSNexperiaCounters, DividersL7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedIRF540N
TO-2201 N-channel 1.35nF 100V 130W 280pF 33A 35mΩ@10V 4V 52nC@10V 85pF N-Channel TO-220 MOSFETs ROHSOSENMOSFETs
README
README.mdAZ5 Robot
Parts
115| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C11, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26, C27 +5 |
| 16 | WS2812B | WS2812B:WS2812B_data-bridgeable | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12, LED13, LED14, LED15, LED16 |
| 9 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2, R3, R4, R5, R9, R10, R12, R14, R25 |
| 8 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R7, R11, R13, R15, R21, R22, R23, R24 |
| 5 | D | other:DO-214AA | D3, D4, D5, D6, D7 |
| 4 | 11,3K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R17, R18, R19, R20 |
| 4 | HEF4040BT | HEF4040BT:SOIC127P600X175-16N | U4, U5, U6, U7 |
| 4 | LM2907 | LM2907:SOIC8 | U8, U9, U10, U11 |
| 4 | e100nF | Capacitor_SMD:CP_Elec_4x5.3 | C5, C6, C7, C8 |
| 4 | e1uF | Capacitor_SMD:CP_Elec_4x5.3 | C9, C10, C29, C30 |
| 4 | e47uF | Capacitor_SMD:CP_Elec_6.3x5.3 | C3, C31, C33, C35 |
| 3 | IRF540N | other:D2PAK | Q1, Q2, Q3 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2 |
| 2 | 249 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R16 |
| 2 | L7805 | Compluino_03:7805 | U12, U13 |
| 2 | LED | LED_SMD:LED_1210_3225Metric_Pad1.42x2.65mm_HandSolder | D1, D2 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R8 |
| 1 | 220nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C12 |
| 1 | 2K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6 |
| 1 | 74LS247 | other:SO16 | U2 |
| 1 | ATmega2560-16AU | Package_QFP:TQFP-100_14x14mm_P0.5mm | U1 |
| 1 | CC56-12SYKWA | Display_7Segment:CA56-12SYKWA | U3 |
| 1 | Conn_01x02_INPUT | proyectoAjeno:XT30PW-F2 | J37 |
| 1 | Conn_01x04_OLED | Compluino_03:OLED | J12 |
| 1 | Crystal | Compluino_03:Crystal | 16MHz1 |
| 1 | DOWN | huellas:PULSADOR | SW9 |
| 1 | HOLE1 | huellas:hole | J29 |
| 1 | HOLE2 | huellas:hole | J30 |
| 1 | HOLE3 | huellas:hole | J31 |
| 1 | HOLE4 | huellas:hole | J32 |
| 1 | LEFT | huellas:PULSADOR | SW7 |
| 1 | OK | huellas:PULSADOR | SW8 |
| 1 | RESET | huellas:PULSADOR | SW1 |
| 1 | RIGHT | huellas:PULSADOR | SW6 |
| 1 | R_POT | Compluino_03:Potenciometro | RV1 |
| 1 | SW_DIP_x08 | huellas:SWITCH | SW10 |
| 1 | UP | huellas:PULSADOR | SW5 |
More from Complubot/AZ5
4- 2 layers80 × 132 mm

- 2 layers47 × 75.6 mm

- 2 layers60 × 82 mm

- 2 layers21.4 × 26.4 mm

Similar boards
- 4 layers70.7 × 56.9 mm

HEI Shift Light
drewsum/HEI_Shift_Light
An automotive shift light meant to integrate into the TACH signal from an HEI distributor, to be embedded in a dashboard
112 parts - 4 layers243.8 × 243.8 mm

- 2 layers68.6 × 53.3 mm

ShieldArduino Displays7Segmentos
tidus747/Proyectos_KiCAD
Proyectos realizados en KiCAD a modo de tutoriales en Piensa 3D (https://www.youtube.com/channel/UC0-azsu5e8CxZfTl9mmafww)
21 parts12GPL-3.0 - 4 layers138.4 × 138.3 mm

GRBL board
ephemeridis/GRBL_board
This is a PCB designed to run GRBL, an open source CNC control software that is designed and optimised for Arduino.
287 parts2GPL-3.0 - 2 layers189.5 × 178 mm

- 2 layers104 × 129 mm

- 2 layers95 × 90.5 mm

- 2 layers96.8 × 97 mm

Psoc5power
profdc9/DRSSTC-PCB-Pack
A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.
133 parts59
Questions
What parts does the MAXPOWER use?
115 parts, built around the ATMEGA2560-16AU, LM2907, 74LS247P-E and HEF4040BT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MAXPOWER KiCad files?
From the Complubot/AZ5 repository on GitHub, at the commit this page was made from: the board is ELECTRONICA/MAXPOWER/MAXPOWER.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the MAXPOWER design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).