
UVerter
owntech-foundation/micro-inverter
A repository to do collective work on an open source micro-inverter.

cirBATT open hardware 48 V to 230 V battery inverter: KiCad power electronics, EGS005Q control and second-life lithium battery integration. Prototype under review.
CirBATTverter 1KWH is an open-source printed circuit board by cirBATT, from the cirBATT/cirbattverter repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 4-layer board of 190.3 × 103.1 mm with 169 parts on 96 nets, routed with 1,023 tracks and 824 vias.
It is built around the CS4200V-01L, L7805 and ES1JW. Its parts include 56 capacitors, 45 resistors, 25 diodes, 13 transistors and 5 ICs. It belongs with the power boards of this library.
An open hardware 48 V → 230 V sine-wave inverter, designed to run from second-life lithium battery packs.
Built by cirBATT, Grenoble, France — we collect end-of-life lithium batteries, requalify them cell by cell and reassemble them into second-life packs. This inverter is the stage that turns such a pack into usable mains power.
⚠️ This board handles lethal voltages
The output is 230 V AC and the DC bus is at mains-level potential. Capacitors stay charged after power-down. A lithium pack can deliver hundreds of amps into a short circuit.
Do not build or power this board unless you are trained to work on mains equipment and have the right tools — isolation transformer, differential probes, RCD-protected bench. This design has not been certified to any safety standard. It is published as an engineering reference, not as a product ready to install in a home.
| Input voltage | 48 V nominal (lithium-ion pack) |
| Output voltage | 230 V AC |
| Output frequency | Set by the controller board |
| Rated power | 1 kW |
| Input stage | Semi-resonant DC-DC converter |
| Control | EGS005Q sine-wave driver board (off-the-shelf) |
| Copper weight | 70 µm on both boards |
The resonant frequency of the input stage is set on the controller board — see Getting started.
The project is made of two boards:
hardware/inverter/ — main boardKiCad 10 project. 4 copper layers, 1.6 mm, ~199 components. Includes the
custom symbol and footprint libraries it depends on (Components_models/,
*.pretty/) and STEP models in 3d/.
hardware/planar-transformer/ — planar transformerKiCad 10 project. 8 copper layers — the transformer windings are etched into the PCB itself rather than wound on a bobbin, which keeps leakage inductance low and the assembly flat and repeatable.
hardware/mechanical/Cirbatt.step — 3D model of the assembly, for enclosure design and fit checks.
production/Files to order the boards without opening KiCad:
| File | Use |
|---|---|
inverter/gerber.zip | Gerbers for the main board |
inverter/*_JLCPCB_BOM.xlsx | Bill of materials, JLCPCB format |
inverter/*_CPL_JLCPCB.xlsx | Pick-and-place positions |
planar-transformer/Gerbers.zip | Gerbers for the transformer |
Specify 70 µm (2 oz) copper when ordering. The default is 35 µm, and at 1 kW that difference matters: the tracks are sized for the heavier copper.
1. Open the design. Install KiCad 10 or
later and open hardware/inverter/cirBATTverter_1KWH.kicad_pro. The custom
libraries are referenced relatively, so they resolve as long as you keep the
folder structure.
2. Order the boards. Upload the files from production/ to your
fabricator. Both boards need 70 µm copper.
3. Get the controller. The SPWM control is not on this board. It uses an EGS005Q driver module, a widely available off-the-shelf part. Its user manual and schematic are published by the manufacturer — we do not redistribute them here, as they are not ours to license. Search for EGS005Q sine wave inverter driver board to find the current documentation and suppliers.
4. Set the resonant frequency of the input stage on the controller board, to match the semi-resonant converter.
Hardware is released under the
CERN Open Hardware Licence Version 2 — Strongly Reciprocal
(CERN-OHL-S-2.0).
In short: you may study, modify, manufacture and sell this design, including commercially. If you distribute a modified version, or a product containing one, you must make your modified sources available under the same licence. Improvements to the design stay available to everyone.
This is a reciprocal licence by choice. We would rather the design stay open than be absorbed into a closed product.
Issues and pull requests are welcome — see CONTRIBUTING.md. Bench measurements, thermal data and failure reports are especially useful: we publish the design, but real-world validation is what makes it trustworthy.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 680pF | Capacitor_SMD:C_1206_3216Metric | C17, C21, C38, C39, C40, C41, C42, C43, C44, C45, C46, C47, C48, C49 |
| 13 | 22uF | Capacitor_SMD:C_2220_5750Metric | C1, C16, C22, C23, C24, C25, C26, C27, C28, C29, C30, C32, C37 |
| 8 | 10 | Resistor_SMD:R_0805_2012Metric | R1, R6, R7, R8, R10, R11, R14, R15 |
| 8 | 1N4148 | Diode_SMD:D_SOD-123 | D1, D4, D5, D6, D7, D8, D9, D10 |
| 8 | Q_NMOS_GDS | Package_SON:Infineon_PG-TDSON-8_6.15x5.15mm | Q1, Q2, Q4, Q5, Q6, Q7, Q8, Q9 |
| 5 | 100k | Resistor_SMD:R_0805_2012Metric | R31, R32, R38, R41, R46 |
| 5 | 10m | Resistor_SMD:R_2512_6332Metric | R52, R57, R58, R59, R60 |
| 4 | 100n | Capacitor_SMD:C_0805_2012Metric | C7, C8, C9, C11 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R9, R12, R13 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric | C51, C52, C54, C55 |
| 4 | 2.2uF | Capacitor_SMD:C_1206_3216Metric | C12, C18, C33, C34 |
| 4 | 33 | Resistor_SMD:R_0805_2012Metric | R26, R27, R28, R51 |
| 4 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C53, C56, C101, C102 |
| 4 | 453k | Resistor_SMD:R_0805_2012Metric | R43, R44, R47, R48 |
| 4 | CID12N65D | circBatt_footprints:DFN-10_L8.0-W6.0_CID12N65D | Q14, Q15, Q16, Q17 |
| 4 | D | C20605567:C20605567 | D3, D11, D12, D13 |
| 4 | D | Diode_SMD:D_SOD-123F | D18, D20, D21, D22 |
| 4 | D | Package_TO_SOT_SMD:TO-277A | D25, D26, D27, D28 |
| 3 | NTC 10k | Resistor_SMD:R_0805_2012Metric | TH2, TH3, TH4 |
| 2 | 12k | Resistor_SMD:R_0805_2012Metric | R39, R50 |
| 2 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C13, C19 |
| 2 | 22uH | APS1040M220A:IND-SMD_L12.3-W12.3_SMDRI127 | L2, L3 |
| 2 | 2k | Resistor_SMD:R_0805_2012Metric | R33, R40 |
| 2 | 3.3R | Resistor_SMD:R_0805_2012Metric | R102, R103 |
| 2 | 3.3nF | Capacitor_SMD:C_0603_1608Metric | C14, C31 |
| 2 | 49.9k | Resistor_SMD:R_0805_2012Metric | R45, R49 |
| 2 | 56pF | Capacitor_SMD:C_0603_1608Metric | C15, C20 |
| 2 | 5uF | Capacitor_THT:C_Rect_L29.0mm_W11.0mm_P27.50mm_MKT | C50, C57 |
| 2 | Conn_01x01 | XFCN TR34070:Untitled | J1, J2 |
| 2 | D | Package_TO_SOT_SMD:TO-252-2 | D19, D23 |
| 2 | ES1JW | circBatt_footprints:D_SOD-123 | D101, D102 |
| 2 | LM5013DDAR | LM5013:CONV_LM5013DDAR | U3, U4 |
| 1 | 0.33uF | Capacitor_SMD:C_2220_5750Metric | C36 |
| 1 | 100nF | Capacitor_THT:C_Rect_L24.0mm_W10.1mm_P22.50mm_MKT | C2 |
| 1 | 100nF | Capacitor_SMD:C_2220_5750Metric | C35 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D17 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R34 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 22uF | Shun Xiang Nuo SMMS1770-330M:IND-SMD_L17.5-W17.5 | L1 |
| 1 | 27 | Resistor_SMD:R_0805_2012Metric | R25 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric | R30 |
| 1 | 360k | Resistor_SMD:R_0805_2012Metric | R36 |
| 1 | 390k | Resistor_SMD:R_0805_2012Metric | R35 |
| 1 | 4.7k | Resistor_SMD:R_0805_2012Metric | R37 |
| 1 | 6.2k | Resistor_SMD:R_0805_2012Metric | R42 |
| 1 | Buzzer | buzzer:Untitled | BZ1 |
| 1 | CS4200V-01L | CS4200V_01L:CS4200V01L | T4 |
| 1 | C_Polarized | Capacitor_THT:CP_Radial_D30.0mm_P10.00mm_SnapIn | C3 |
| 1 | Conn_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1-2-3.81_1x02_P3.81mm_Horizontal | FAN1 |
| 1 | Conn_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-3-5.08_1x03_P5.08mm_Horizontal | J7 |
| 1 | Conn_01x14 | Connector_PinHeader_1.27mm:PinHeader_1x14_P1.27mm_Vertical | J4 |
| 1 | Conn_01x29 | Connector_PinHeader_1.27mm:PinHeader_1x29_P1.27mm_Vertical | J5 |
| 1 | L7805 | Package_TO_SOT_SMD:TO-252-2 | U6 |
| 1 | NPN | Package_TO_SOT_SMD:SOT-89-3 | Q13 |
| 1 | Optocoupler_DC_PhotoNPN_AKEC | Package_SO:SOP-4_7.5x4.1mm_P2.54mm | U1 |
| 1 | TL431DBZ | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | Transformer_1P_1S | Inductor_THT:L_CommonMode_Toroid_Vertical_L22.0mm_W12.0mm_Px9.00mm_Py8.00mm_PRODTech_PDMCAT18107-202ML | T5 |
| 1 | Transformer_1P_2S | PCB_transformer:Untitled | T1 |
The 160 most common of 169 parts.

owntech-foundation/micro-inverter
A repository to do collective work on an open source micro-inverter.

Allen-Synthesis/EuroPi
EuroPi: A reprogrammable Eurorack module based on the Raspberry Pi Pico

peterheinrich/InternetOverSpaghetti
Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.


Tircown/ERCF-easy-brd
More informations on how to reset for flashing:\ https://wiki.seeedstudio.com/Seeeduino-XIAO/#enter-bootloader-mode

matthewcieplak/super-sixteen
Code and schematics for the Super Sixteen Eurorack sequencer

NikodemBartnik/Mini-Mars-Rover
Educational robotic platform made to look like a mini mars rover

starlightk7/OpenSFC
OSHW Reproduction Parts related to the Super Famicom / Super Nintendo game console
It measures 190.3 × 103.1 mm and has 4 copper layers, 1.6 mm thick.
169 parts, built around the CS4200V-01L, L7805 and ES1JW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the cirBATT/cirbattverter repository on GitHub, at the commit this page was made from: the board is hardware/inverter/cirBATTverter_1KWH.kicad_pcb and its schematic hardware/inverter/cirBATTverter_1KWH.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).