
8088-FE2010A SBC
skiselev/micro_8088
Micro 8088 - IBM XT Compatible Processor Board based on Faraday FE2010 chipset

This allow to amplify the RPI4 radioberry version TX output, to suitable level for 10W QRP Labs Linear Power Amplifier.
Pa driver is an open-source printed circuit board by cinosh07, from the cinosh07/Radioberry-Filters-Interface repository on GitHub. It is a 2-layer board of 54.6 × 34.3 mm with 18 parts on 10 nets, routed with 40 tracks and 2 vias.
It is built around the PN2222A. Its parts include 4 resistors, 3 capacitors, 1 transistor and 1 connector.
Radioberry project https://github.com/pa3gsb/Radioberry-2.x
This allow to amplify the RPI4 radioberry version TX output, to suitable level for 10W QRP Labs Linear Power Amplifier.

Mesurement.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nf | Capacitor_THT:C_Disc_D5.1mm_W3.2mm_P5.00mm | C1, C2, C3 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Vertical | R2 |
| 1 | 3.9k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Vertical | R1 |
| 1 | 4.7 ohm | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Vertical | R3 |
| 1 | 47ohm | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Vertical | R4 |
| 1 | GND | TestPoint:TestPoint_Pad_4.0x4.0mm | H4 |
| 1 | GND Sig | TestPoint:TestPoint_Pad_4.0x4.0mm | H2 |
| 1 | In-Sig | TestPoint:TestPoint_Pad_4.0x4.0mm | H1 |
| 1 | M1 | MountingHole:MountingHole_3.2mm_M3 | H5 |
| 1 | M2 | MountingHole:MountingHole_3.2mm_M3 | H6 |
| 1 | M3 | MountingHole:MountingHole_3.2mm_M3 | H7 |
| 1 | M4 | MountingHole:MountingHole_3.2mm_M3 | H8 |
| 1 | Out-sig | TestPoint:TestPoint_Pad_4.0x4.0mm | H3 |
| 1 | PN2222A | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | Power Connector | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Transformer_1P_2S | pa-driver:Transformer2 1p 2s Binocular | T1 |

skiselev/micro_8088
Micro 8088 - IBM XT Compatible Processor Board based on Faraday FE2010 chipset

Staacks/there.oughta.be
Projects featured on my blog at https://there.oughta.be


plusvic/simplebus2-intercom
General description of the Simplebus2 protocol used by some Comelit's intercoms. Hardware for retransmitting Simplebus2 messages over UART.




It measures 54.6 × 34.3 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the PN2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the cinosh07/Radioberry-Filters-Interface repository on GitHub, at the commit this page was made from: the board is pa driver/pa-driver/pa-driver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask cinosh07 before reusing the design.