Skip to the content
2 layers75 × 38 mmGhost fader stack control, the printed circuit board in 3D

Ghost fader stack control

chris-albert/ghost-fader

MIDI-controlled volume and pan for balanced stereo synths (Teensy 4.0 + PGA2310)

Size
75 × 38 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
28
Pads
90
Tracks, vias
166, 3
Pours
9
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
3 Sep 2026
Updated
19 Oct 2026

Overview

Ghost fader stack control is an open-source printed circuit board by chris-albert, from the chris-albert/ghost-fader repository on GitHub. It is a 2-layer board of 75 × 38 mm with 24 parts on 28 nets, routed with 166 tracks and 3 vias.

It is built around the ISO7762FDW and L78L05CZ. Its parts include 8 capacitors, 3 ICs, 2 resistors, 2 inductors and 1 diode. It belongs with the audio and music boards and the RP2040 boards of this library.

Main components

2

README

README.md

Ghost Fader

USB-MIDI-controlled volume and pan for two balanced 1/4" line channels. Balanced in, always-balanced out, one input becomes stereo automatically. Bus-powered Seeed XIAO RP2040 plus a 2x2 gain matrix of PGA2310 attenuators. Revision D: USB only, no DIN jack, no DC jack; the audio side is galvanically isolated from the computer. A TI ISO7762F carries the four control lines and two sense lines across a split in the ground pours, the DC-DC module is the only power path across it, and a 78L05 makes the PGA logic supply on the audio side. About $6 of parts on top of rev C (XIAO RP2040, Traco TBA 2-0522).

The full schematic package (block diagram, five sheets, level budget, USB power budget, MIDI map, build order) is published at https://chris-albert.github.io/ghost-fader/ (source: docs/index.html). This file is the short version.

Signal chain

text
J1/J2 TRS in -> THAT 1246 (bal->SE, -6 dB) -> 2x PGA2310 (2x2 matrix, 4 gains)
             -> OPA1642 summers (non-inverting, x2) -> THAT 1646 (SE->bal, +6 dB) -> J3/J4 TRS out
  • Net gain balanced-to-balanced is 0 dB at PGA code 192. PGA range is +31.5 to -95.5 dB in 0.5 dB steps, plus hard mute.
  • A TS plug on an input grounds the ring, so unbalanced sources need no switch. A TS plug on an output is handled by the cross-coupled 1646.
  • Plug sense: each input jack's ring-normal contact is pulled up to +5VA by 100 k and read by the XIAO (D0, D1) through the isolator. Tip-normal is grounded.
  • Matrix: U3 carries the direct paths (L->L, R->R), U4 the cross paths (L->R, R->L). Mono mode pans the L input across both outputs with a constant-power law; stereo mode uses balance.

Power

Everything runs from the USB cable. There is no external power supply, DC jack or wall adapter. The XIAO's 5V pin is USB VBUS straight through, so it exports the bus 5 V. That feeds PS1, a small isolated 5 V -> +/-12 V DC-DC converter soldered to the board (Traco TBA 2-0522, 2 W, SIP-7), for the analog stages. The PGA2310 logic supply and the audio side of the isolator run on +5VA, made from +12 V by U10, a 78L05, so nothing on the audio side references the USB ground.

PS1 is unregulated: the rails follow the USB voltage and the load, from about +/-11 V on a sagging port to about +/-14 V at 5.25 V and light load. Every part on the rails is rated for that (the PGA2310 absolute maximum is 16 V, which is why the +/-15 V TBA 2-0523 is not used). Headroom at +/-12 V is about 2 dB less than on +/-15 V: the output driver clips near +22 dBu instead of +24. Total rail capacitance, about 120 uF per rail, stays under the 220 uF the TBA 2 allows.

LoadCurrent at 5 V
XIAO RP2040, isolator side 1~35 mA
PS1 delivering ~55 mA on +12 V (analog ~40 mA plus U10 ~15 mA) and ~40 mA on -12 V, at ~80 %~230 mA
LED~2 mA
Total~265 mA typical, ~330 mA worst case

USB 2.0 ports allow 500 mA; USB 3 / USB-C ports allow 900 mA or more. Use a real port or a powered hub and a data cable (not charge-only).

Ground: there are two. GND_USB is the XIAO, its USB-C shell, the DIP switch, the LED, the ferrite, the reservoir cap, the isolator's side 1 and the DC-DC input. GND is everything audio, the PGA logic, the isolator's side 2 and the DC-DC output. They meet only through C45, a 1 nF cap that gives the converter's switching noise a local return so it does not radiate as common mode, and R17, 1 M, which stops the audio side drifting when nothing is plugged in. So the audio ground follows whatever gear is plugged into the jacks, the way a transformer-isolated DI does, and the computer's ground noise never enters the box. The isolator is the F (fail-safe low) part: when the XIAO is unpowered its outputs sit low, so the PGAs stay muted until the firmware is up.

For that to hold in the box, the XIAO's USB-C shell must not touch the enclosure: the enclosure belongs to the audio ground (bond it to the jack sleeves or to the PS1 Common pad with a wire, since the NRJ6HF bushings are plastic), so use a plastic bezel or a clearance cutout for the USB-C, not a metal-to-metal fit.

XIAO RP2040 pins

PinSignal
USB-CMIDI in (class-compliant, TinyUSB) and 5 V in
5VUSB 5 V out to FB1, PS1
3V3Isolator side 1 (U8 VCC1)
D0, D1 (GP26, GP27)SENSE_L, SENSE_R through U8 (100 k pull-ups to +5VA on the audio side, internal pull-up off)
D2-D5 (GP28, GP29, GP6, GP7)MIDI channel DIP, INPUT_PULLUP
D6 (GP0)/MUTE to both PGA2310 through U8 (10 k pull-down on the PGA side mutes at boot)
D7 (GP1)/CS through U8
D8 (GP2, SCK)SCLK through U8
D9 (GP4, the MISO pin)MIDI activity LED. Nothing comes back from the PGAs, so bit-bang the frame or leave SPI RX unassigned
D10 (GP3, MOSI)SDI of U3 through U8; U3 SDO chains to U4 SDI

The schematic symbol numbers the XIAO's 14 pins as Seeed's footprint does: 1-7 down the left row from the USB end (D0-D6), 8-14 up the right row (D7-D10, 3V3, GND, 5V).

SPI frame: 32 bits per update, U4's 16-bit word first, then U3's. Each word is the right-channel byte then the left. Code = 192 + 2 * dB, 0 = mute.

MIDI map (proposed)

CCFunction
7Volume, 127 = 0 dB, 40*log10(v/127) dB
10Pan (mono: constant power; stereo: balance)
14, 15L / R input trim, +/-12 dB, 64 = 0 dB
85Mono sum on/off
120Hard mute

Parts list

Prices are approximate single-piece USD.

RefQtyPartDescription~$ eaNotes
U1, U22THAT 1246S08Balanced line receiver, -6 dB5.50Alt: TI INA137
U3, U42TI PGA2310PAStereo volume control, +/-15 V, SPI, DIP-1611.00PGA2310UA for SOIC. Not PGA2311
U51TI OPA2134PADual JFET op-amp, DIP-84.00Alt: NE5532P
U6, U72THAT 1646S08Cross-coupled balanced driver, +6 dB5.50Alt: TI DRV134
U81TI ISO7762FDW6-channel digital isolator, 4 forward / 2 reverse, fail-safe low, SOIC-16W4.50Not the plain ISO7762 (defaults high, which would unmute the PGAs while the XIAO boots)
U91Seeed XIAO RP2040MCU with USB-C, class-compliant USB MIDI via TinyUSB5.00On header pins. Its 5V pin is USB VBUS and feeds the board
U101L78L055 V 100 mA regulator, TO-92, from +12 V0.30Makes +5VA on the audio side for the PGA logic and U8 side 2, about 15 mA
PS11Traco TBA 2-0522Board-mounted isolated DC-DC, 4.5-5.5 V in, +/-12 V 80 mA, 2 W, unregulated, SIP-75.00Fed from USB 5 V, not an external supply. Any industry-standard SIP-7 2 W +/-12 V module (Mornsun B0512, RECOM RB-0512D) has the same pinout. Not a +/-15 V part: unregulated rails would pass the PGA2310's 16 V maximum at light load
FB11Ferrite bead 600 R @ 100 MHz, >=1 AKeeps switching noise off USB0.20
J1-J44Neutrik NRJ6HF1/4" TRS PCB jack, T and R switching3.00Switch contacts used on J1, J2 only
L1, L2210 uH, >=300 mARail filters0.40
SW114-way DIPMIDI channel0.80
LED113 mm LEDActivity0.15
C3-C6, C17-C20810 uF non-polarC3-C6 coupling into PGA inputs, C17-C20 THAT 1646 sense caps0.40Nichicon UES
C1, C2, C7-C10, C15, C168100 pF C0GRF caps at every jack tip and ring0.10
C11147 uF 10 V low-ESRUSB-side reservoir0.25
C12, C132100 uF 25 VRail filters0.25
C14110 uF+5VA logic rail0.10
C21-C39, C4420100 nF X7ROne per supply pin; C37/C38 at U10, C39/C44 at U80.05
C4511 nF 1 kV ceramicGround barrier cap, GND to GND_USB0.15Straddles the pour gap at PS1
C40-C43410 uF 25 V+/-12 V bulk, input end and output end0.10
R2-R9810 k 1%Summing and feedback0.05
R10-R13410 ROutput build-out0.05
R1, R142100 kPlug-sense pull-ups to +5VA0.05100 k, not 1 M: U8's inputs leak up to 10 uA
R15, R16210 k, 1 kMute pull-down, LED0.05
R1711 MGround barrier bleed, GND to GND_USB0.05Straddles the pour gap
CABLE1USB A/C to USB-C data cableShort and thick3.00
ENC1Hammond 1590BBDie-cast enclosure12.00
PCB12-layer 108 x 80 mmGerbers in hardware/gerbers/10.00Corner notches clear the 1590BB lid-screw bosses
J5, J622x6 shrouded box header, 2.54 mmTwo-board stack only: board link0.30Stock IDC-Header_2x06 footprint
RIBBON112-way IDC ribbon, 2x6 sockets both ends, ~50 mmTwo-board stack only: J5 to J6, pin for pin1.50
STANDOFF4M3 x 15 mm standoff, 8 M3 screwsTwo-board stack only: control board above the main board1.5015 mm clears the 11 mm radial caps under it

Estimated total: about $116 per unit, or about $106 with the narrow board in a printed box instead of the 1590BB, about $112 for the two-board stack (two small boards and the link parts). Cost-down variant with one PGA2310 and a DG419 routing switch instead of the matrix: about $90, loses cross-feed and mono-sum.

Full schematic

hardware/kicad/ is a KiCad 9 project: root sheet plus input, matrix, output, control and power sheets (a second root, ghost-fader-stack.kicad_sch, shares those five sheets and adds sheet 6, the board-link connector pair for the two-board stack below), with a project symbol library (THAT 1246/1646, PGA2310, OPA2134, XIAO RP2040, TBA 2, ISO7762F, 78L05, the GND_USB power symbol) and a footprint for the XIAO on header pins; the TBA 2, the isolator and the regulator use KiCad's stock footprints. ERC passes with zero violations on both roots and the netlist (61 nets, 263 pins; 287 with the link connectors) has been checked pin-for-pin against hardware/kicad/tools/check.py. bom.csv is the KiCad BOM export. Rendered sheets and a PDF are in docs/schematic/ and on the published page.

Every part has a footprint; the jacks use KiCad's stock Neutrik NRJ6HF horizontal footprint, whose pad names match the symbol. The schematic is generated by hardware/kicad/tools/gen.py; edit it in KiCad directly from here on, or edit the generator and rerun it (it needs KiCad's stock symbol libraries at the macOS install path).

PCB

hardware/kicad/ghost-fader.kicad_pcb is a routed 2-layer board, 108 x 80 mm, DRC clean against the schematic (the only warnings are the jack noses' and the USB-C shell's silkscreen crossing the board edge, which is inherent to the footprints). Gerbers, Excellon drill file and drill map are in hardware/gerbers/ and zipped as hardware/ghost-fader-gerbers.zip; upload the zip as-is to JLCPCB, PCBWay or OSH Park (2 layers, 1.6 mm, any finish). Renders are in docs/pcb/ and on the published page.

Layout, rear edge at the top:

  • The four jacks sit along one long edge, IN L, IN R, OUT L, OUT R at 19, 39, 68 and 90 mm from the left edge. Their threaded noses stick 1.5 mm past the board edge so the panel nuts have thread to bite. Drill the enclosure wall on those centres.
  • Signal flows down and around: jacks -> RF caps -> THAT 1246 receivers (rotated so the inputs face the jacks) -> coupling caps -> the two PGA2310s side by side, analog pins facing up and SPI pins facing the XIAO -> OPA2134 summer and its resistors on the right -> THAT 1646 drivers under the output jacks with their sense caps and build-outs.
  • The front-left corner is the USB ground island: the XIAO with its USB-C face flush with the front edge (cut a slot in the front wall for the plug, and keep the shell off the metal), the DIP switch to its right, the LED and its resistor in the left column, the ferrite and reservoir cap, and the input end of the DC-DC. The isolator U8 lies across the top edge of the island with its USB row inside and its audio row outside; PS1 lies across the island's right edge the same way. The barrier parts C45 and R17 straddle the gap in the left column. The 78L05, rail filters and the rest of the power section are front-centre on the audio side, the far corner from the input receivers.
  • Every decoupling cap is within a few mm of its supply pin. The +/-12 V bulk pairs are at the input end (C40/C41, between J2 and J3) and the output end (C42/C43, right edge).
  • Two ground pours on both layers, audio and USB, separated by a 2 mm gap with no copper. A rule area over the gap keeps the router out, and only U8, PS1, C45 and R17 cross it; a script check confirms no track or via enters the gap. Each pour is stitched by the ground tracks the router laid first, so the schematic's "star at PS1 COM" becomes a plane on the audio side. Power nets are 0.6 mm tracks, signals 0.3 mm, 0.25 mm clearance; anyone can fab it.
  • The board is held by the four jack nuts. The corners are notched 7.5 x 6.5 mm to clear the 1590BB lid-screw bosses. Check fit against the actual box before ordering: the inside is about 112 x 86 mm at the base, so there is 2 to 3 mm each way.

The LED is a through-hole 3 mm on the left edge near the front corner; bend it out through a hole in the left wall, or toward the front panel, or fit a light pipe. To regenerate the board from the schematic (placement is a table in tools/build_pcb.py, routing is Freerouting):

text
cd hardware/kicad
kicad-cli sch export netlist --format kicadsexpr -o /tmp/gf.net ghost-fader.kicad_sch
<KiCad python3> tools/build_pcb.py /tmp/gf.net          # placement, outline, pours, rules
<KiCad python3> tools/route.py ghost-fader.kicad_pcb <freerouting launcher or jar>
kicad-cli pcb drc --severity-all --schematic-parity -o /tmp/drc.rpt ghost-fader.kicad_pcb

<KiCad python3> is the interpreter bundled with KiCad (on macOS /Applications/KiCad/KiCad.app/Contents/Frameworks/Python.framework/Versions/Current/bin/python3), which has the pcbnew module. Freerouting 1.9 was used; 2.4 routes the same board but writes an empty session file from the command line.

Narrow in-line PCB

hardware/kicad/ghost-fader-narrow.kicad_pcb is the same schematic on a second, independent board shaped for a signal chain: 207 x 38 mm, inputs on the right end, outputs on the left, the XIAO's USB-C out of the middle of the rear long edge, so the box sits in-line like a pedal. It is as narrow as two side-by-side jacks allow: the NRJ6HF jacks sit on an 18 mm pitch (34.8 mm) plus edge clearance. The XIAO (21 mm long) lies across the board with its USB-C at the rear edge. It needs a 3D-printed box: about 40 x 210 mm inside, a ledge under the long board edges, two jack holes in each end wall on the jack centres (10 and 28 mm from the rear edge of the board, at the NRJ6HF bushing height), a USB-C slot and a 3 mm LED hole in the rear wall. No mounting holes; the four jack nuts hold the board. Routed, DRC clean against the schematic (the same jack-nose silkscreen warnings as the main board), 0.6 mm power tracks, 0.3 mm signals, split ground pours both sides. The USB ground island is a pocket on the rear edge, x 104 to 141 mm by 28 mm deep, holding the XIAO, LED, DIP switch, ferrite and reservoir; the audio ground wraps under it so the rails and audio pass from the input end to the output end. U8 straddles the pocket's left wall, PS1 its right wall. Gerbers in hardware/gerbers-narrow/ and hardware/ghost-fader-narrow-gerbers.zip; renders in docs/pcb-narrow/. The 1590BB board above is unchanged.

Everything runs in columns along the length, left to right: output jacks, RF caps, drivers with their sense caps stacked, build-outs and 100n, summer with its resistors, coupling caps, the two PGA2310s stacked across the board with their SPI rows facing each other, the isolator, the LED and XIAO, DIP switch, ferrite and reservoir over the barrier parts and +/-12 V bulk caps, DC-DC, 78L05 and rail filters, receivers with the sense pull-ups, bulk caps, RF caps, input jacks. The LED sits at the rear edge just left of the XIAO, about 107 mm from the left end. Most reference labels sit on the part bodies because there is no room beside them; they read on the bare board. Parts come within 1 mm of the long edges, so give the printed walls clearance above the board edge.

To regenerate: same steps as above with tools/build_pcb_narrow.py in place of tools/build_pcb.py and ghost-fader-narrow.kicad_pcb as the board.

Two-board stack

The narrow board is long because everything sits in one row. hardware/kicad/ghost-fader-stack-main.kicad_pcb and ghost-fader-stack-control.kicad_pcb split the same circuit over two boards, one above the other, so the in-line box drops from 207 to 150 mm long and the jacks are 57 mm closer together. Both boards are 38 mm wide like the narrow one; the box is about 40 x 152 mm inside and about 32 mm tall instead of 20.

  • Main board, 150 x 38 mm: the jacks and the whole audio path. Output jacks on the left end, then RF caps, THAT 1646 drivers with their sense caps, build-outs and summer, the PGA2310 coupling caps, the two PGA2310s stacked across the board, J5 (the link header) with the plug-sense pull-ups under it, the THAT 1246 receivers, the +/-12 V bulk caps, RF caps and the input jacks on the right end. It is all audio ground: one pour per layer, no split. Four 3.2 mm standoff holes at (67, 3.8), (67, 34), (119.25, 3.8) and (119.25, 34) mm from the left (output) end and the rear edge, each inside a 3.4 mm radius copper keepout so a metal standoff touches no ground.
  • Control board, 75 x 38 mm: the XIAO with its USB-C at the rear edge, LED, DIP switch, ferrite, reservoir, the isolator U8, the DC-DC PS1, the 78L05, rail filters and J6. It carries the whole ground barrier: its left 37.5 mm is the USB ground island, the rest the audio side, with the 2 mm gap straddled by U8, PS1, C45 and R17 exactly as on the other boards; the same script check confirms no copper crosses the gap. Holes at (8, 3.8), (8, 34), (60.25, 3.8) and (60.25, 34).
  • Mounting: the control board sits on four M3 x 15 mm standoffs with its rear edge flush with the main board's, its left end 59 mm from the output end, so the hole patterns coincide and the XIAO's USB-C comes out of the rear wall 80 mm from the output end. 15 mm clears the 11 mm radial caps under it. A 12-way IDC ribbon about 50 mm long joins J5 and J6 pin for pin: 1 +12V, 2 GND, 3 -12V, 4 GND, 5 +5VA, 6 GND, 7 SCLK, 8 SDI, 9 /CS, 10 /MUTE, 11 SENSE_L, 12 SENSE_R (sheet 6). Everything that crosses is on the audio side of the barrier.
  • Box: like the narrow one but shorter, with the rear-wall USB-C slot and LED hole 15 + 1.6 mm higher (the LED is on the control board, 32.9 mm from its left end), the DIP switch under the lid, and the four jack holes in the end walls as before. The main board hangs on the four jack nuts; the control board on the standoffs.

Both boards are routed and DRC clean (0 unconnected, the usual jack-nose and USB-shell silkscreen warnings), 0.6 mm power tracks, 0.3 mm signals. Schematic parity is checked against ghost-fader-stack.kicad_sch; since each board holds half the parts, the parity report lists the other board's footprints as missing and nothing else, and no pad disagrees with the schematic. Note that kicad-cli pcb drc --schematic-parity only finds the schematic when the board file has the schematic's name, so to check parity copy a board next to the schematic as ghost-fader-stack.kicad_pcb first (the narrow board was re-checked the same way against ghost-fader.kicad_sch and is clean). Gerbers in hardware/gerbers-stack-main/ and hardware/gerbers-stack-control/ with zips beside them; renders and copper SVGs in docs/pcb-stack/.

To regenerate both boards from the stack schematic (placement for both is in tools/build_pcb_stack.py):

text
cd hardware/kicad
kicad-cli sch export netlist --format kicadsexpr -o /tmp/gf-stack.net ghost-fader-stack.kicad_sch
<KiCad python3> tools/build_pcb_stack.py /tmp/gf-stack.net    # writes both boards
<KiCad python3> tools/route.py ghost-fader-stack-main.kicad_pcb <freerouting>
<KiCad python3> tools/route.py ghost-fader-stack-control.kicad_pcb <freerouting>

Notes

  • The overview sheets label IC pins by function. The KiCad schematic in hardware/kicad/ has the real pin numbers and is the one to lay out from.
  • The PGAs are driven at 5 V by the isolator's outputs. Never route a PGA SDO (5 V) back toward the XIAO: the RP2040 is not 5 V tolerant, and nothing crosses U8 in that direction except the two sense lines.
  • Ground is two pours on both layers with a 2 mm gap; the DC-DC is at the far end of the board from the input receivers.

Parts

24
QtyValueFootprintReferences
4100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC37, C38, C39, C44
4M3 standoffMountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
2100u 25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC12, C13
210uH 300mAInductor_THT:L_Axial_L7.0mm_D3.3mm_P10.16mm_Horizontal_Fastron_MICCL1, L2
11MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR17
11kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR16
11n 1kVCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC45
147u low-ESRCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC11
1600R@100MHz 1AInductor_THT:L_Axial_L7.0mm_D3.3mm_P10.16mm_Horizontal_Fastron_MICCFB1
1ISO7762FDWPackage_SO:SOIC-16W_7.5x10.3mm_P1.27mmU8
1L78L05Package_TO_SOT_THT:TO-92_Inline_WideU10
1MIDI actLED_THT:LED_D3.0mmLED1
1MIDI channelButton_Switch_THT:SW_DIP_SPSTx04_Slide_6.7x11.72mm_W7.62mm_P2.54mm_LowProfileSW1
1TBA 2-0522Converter_DCDC:Converter_DCDC_TRACO_TBA2-xxxx_Dual_THTPS1
1XIAO RP2040GhostFader:XIAO_RP2040_THTU9
1control boardConnector_IDC:IDC-Header_2x06_P2.54mm_VerticalJ6

More from chris-albert/ghost-fader

2
  • 2 layers108 × 80 mmGhost fader, the printed circuit board in 3D

    Ghost fader

    chris-albert/ghost-fader

    MIDI-controlled volume and pan for balanced stereo synths (Teensy 4.0 + PGA2310)

    82 parts
  • 2 layers150 × 38 mmGhost fader stack main, the printed circuit board in 3D

    Ghost fader stack main

    chris-albert/ghost-fader

    MIDI-controlled volume and pan for balanced stereo synths (Teensy 4.0 + PGA2310)

    68 parts

Similar boards

  • 4 layers64 × 64 mmConvey, the printed circuit board in 3D

    Convey

    kennito2035/convey

    CONVEY: open 8-channel patient-isolated EEG/sEMG/ECG acquisition board (ADS1299, KiCad 10)

    146 parts4CERN-OHL-S-2.0
  • 4 layers40 × 40 mmMPPT Inverter, the printed circuit board in 3D

    MPPT Inverter

    DavidBojanovic08/Inverter

    Schematic and PCB

    29 parts
  • 4 layers104.1 × 99.1 mmISA ES1868, the printed circuit board in 3D

    ISA ES1868

    hkzlab/ES1868_ISA8

    ISA 8bit sound card based on the ES1868F sound chip, providing Sound Blaster PRO and OPL3 compatibility in a highly integrated package

    120 parts88
  • 2 layers50.8 × 38.1 mmLk201, the printed circuit board in 3D

    Lk201

    pkoning2/lk201emu

    Emulate DEC LK201 keyboard using a standard PC USB keyboard

    19 parts56BSD-2-Clause
  • 2 layers104 × 73 mmArdf tx, the printed circuit board in 3D

    Ardf tx

    hmatuschek/ardf-tx

    Schematics and firmware for simple ARDF transmitter.

    55 parts5
  • 2 layers32 × 19 mmFan controller, the printed circuit board in 3D

    Fan controller

    flaviut/fan-controller

    a automatic temperature-sensing fan controller

    21 parts2
  • 2 layers99.1 × 99.1 mm4op drum module rev2, the printed circuit board in 3D

    4op drum module rev2

    vk2gpu/4op_drum_synth

    OPL3 based 4-op drum synth module

    117 parts2
  • 4 layers130 × 140 mmPreamp, the printed circuit board in 3D

    Preamp

    djupdal/asd-amp

    275 parts1

Questions

How big is the Ghost fader stack control PCB?

It measures 75 × 38 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ghost fader stack control use?

24 parts, built around the ISO7762FDW and L78L05CZ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ghost fader stack control KiCad files?

From the chris-albert/ghost-fader repository on GitHub, at the commit this page was made from: the board is hardware/kicad/ghost-fader-stack-control.kicad_pcb and its schematic hardware/kicad/control.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ghost fader stack control design in my own project?

Its repository states no licence, so its author keeps all rights: ask chris-albert before reusing the design.