
Robo car
ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

storing custom pcbs and micropython code for home projects
Door relay sensor is an open-source printed circuit board by ChefsSlaad, from the ChefsSlaad/PCBs_and_Micropython repository on GitHub. It is a 2-layer board of 68.6 × 68.6 mm with 20 parts on 27 nets, routed with 130 tracks and 0 vias.
It is built around the WEMOS D1 MINI. Its parts include 5 resistors, 2 ICs, 2 diodes, 2 transistors and 2 switches. It belongs with the home automation and IoT and sensors and measurement boards and the ESP8266 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R4 |
| 2 | 1N4001 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D1, D2 |
| 2 | 2N3904 | Package_TO_SOT_THT:TO-92_Wide | Q1, Q2 |
| 2 | Conn_01x03_Pin | Connector_JST:JST_EH_B3B-EH-A_1x03_P2.50mm_Vertical | MotionSensor1, TempSensor1 |
| 2 | SANYOU_SRD_Form_C | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | K1, K2 |
| 2 | Screw_Terminal_01x03 | TerminalBlock:TerminalBlock_bornier-3_P5.08mm | DoorRelay1, Relay1 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
| 1 | 3K3 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | DoorSensor1 |
| 1 | LOGO | LOGO | G*** |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | PowerIn1 |
| 1 | WeMos_D1_mini | Module:WEMOS_D1_mini_light | U1 |
| 1 | mini-360 | mini360:buck_converter 16.8x22,14 | U2 |

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

ChefsSlaad/PCBs_and_Micropython
storing custom pcbs and micropython code for home projects

nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

bitfixer/bf-romulator
Romulator - RAM/ROM replacement and debug for 6502 CPU systems

alcar21/WemosEM
Cheap power monitor (STC013) with Home Assistant Discover and Wemos D1 Mini / PRO (esp8266)

kholia/Easy-Digital-Beacons-v1
A simple and easy Arduino / Pi Pico / ESP8266-powered WSPR, FT8, and FT4 beacon system which uses NTP + DS3231 RTC for timing. Super extensible! Now comes with optional GPS support.

htumanyan/navien
Navien water heater wire protocol for communication with NaviLink and other attached devices


It measures 68.6 × 68.6 mm and has 2 copper layers, 1.6 mm thick.
20 parts, built around the WEMOS D1 MINI. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ChefsSlaad/PCBs_and_Micropython repository on GitHub, at the commit this page was made from: the board is pcbs/door_relay_sensor/door_relay_sensor.kicad_pcb and its schematic pcbs/door_relay_sensor/door_relay_sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ChefsSlaad before reusing the design.