Skip to the content
2 layersLoad cell, the printed circuit board in 3D

Hardware for EPFL Rocket Team Hermes Supersonic Test Rocket

Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
8
Pads
20
Tracks, vias
31, 8
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
10 Dec 2025
Updated
31 Mar 2026

Overview

Load cell is an open-source printed circuit board by chaxaf, from the chaxaf/Supersonic-Test-Rocket repository on GitHub. It is a 2-layer board with 5 parts on 8 nets, routed with 31 tracks and 8 vias.

It is built around the AD8556ARZ. Its parts include 2 resistors, 2 connectors and 1 IC. It belongs with the sensors and measurement boards of this library.

Main components

1

README

README.md

Hermes II Avionics Redesign

Semester project completed with the EPFL Rocket Team in 2022.

Hermes II is a compact avionics architecture developed for a small experimental rocket intended for validation flights and data generation. The project focused on redesigning the electronics of the original Hermes platform into a smaller, more modular system with telemetry, GPS, multiple sensor boards, and improved integration inside the rocket.

Project summary

The avionics stack is built around one main PCB and three auxiliary PCBs placed in different parts of the rocket:

  • Main PCB in the avionics bay
  • Nosecone PCB for total pressure and wall temperature
  • Static port PCB for static pressure and wall temperature
  • Load cell PCB for thrust measurement signal conditioning

The design integrates:

  • Teensy 3.5 microcontroller
  • GPS
  • XBee telemetry
  • IMU and accelerometer
  • pressure sensors
  • thermocouple interfaces
  • load cell instrumentation amplifier
  • battery management and power regulation

System overview

Rocket overview

Source in repository: docs/Hermes_Presentation.pptx

Avionics bay

Main PCB

The main board had to fit inside a very constrained avionics bay while interfacing with the GPS, telemetry radio, IMU, pressure sensors, thermocouples, Altimax, Wildhorn sensor board, and auxiliary boards. It uses a 4-layer stack-up with dedicated ground and power planes.

System block diagram

Main PCB top

Main PCB routing

Main PCB power planes

GPS layout constraints

One of the most layout-sensitive parts of the board was the GPS section, especially antenna routing and the controlled-impedance microstrip connection.

GPS layout

GPS microstrip stackup

Auxiliary PCBs

Nosecone PCB

Measures total pressure and wall temperature.

Nosecone PCB

Static port PCB

Measures static pressure and wall temperature.

Static port PCB

Load cell PCB

Conditions the load cell signal used for thrust measurement.

Load cell PCB

Main technical points

  • Compact avionics redesign for a constrained rocket airframe
  • Separation of avionics into one main PCB and three auxiliary PCBs
  • Integration of telemetry and GPS
  • Pressure, temperature, acceleration, and inertial sensing
  • Load cell instrumentation for thrust measurements
  • 4-layer PCB design under mechanical, thermal, and routing constraints
  • Manufacturing through a combination of external PCB assembly and manual soldering

Results

According to the final presentation, the following subsystems were functional during project testing:

  • GPS worked outdoors
  • telemetry radio worked
  • thermocouples worked
  • pressure sensors, IMU, and Altimax were functional
  • the accelerometer worked after replacing a faulty capacitor

Main issues and remaining work included:

  • power supply malfunction
  • some MAX31855 thermocouple interfaces failed
  • connector orientation errors that were later corrected
  • remaining validation work for the load cell amplifier and some Wildhorn sensor software

See slides “RESULTATS” and “CONCLUSION” in docs/Hermes_Presentation.pptx.

Repository structure

text
Hermes-II-GitHub/
├── README.md
├── .gitignore
├── docs/
│   ├── Hermes_Presentation.pptx
│   └── report.pdf
├── images/
│   ├── rocket_overview.png
│   ├── avionics_bay.png
│   ├── system_block_diagram.png
│   ├── main_pcb_top.png
│   ├── main_pcb_bottom.png
│   ├── main_pcb_signal_routing.png
│   ├── main_pcb_power_planes.png
│   ├── gps_layout_guidelines.png
│   ├── gps_microstrip_stackup.png
│   ├── nosecone_board.png
│   ├── static_port_board.png
│   └── load_cell_board.png
└── hardware/
    ├── main_pcb/
    ├── nosecone_pcb/
    ├── static_port_pcb/
    └── load_cell_pcb/

Opening the hardware files

The hardware design files are provided in KiCad project format. Open the corresponding .kicad_pro file in each hardware subfolder.

Parts

5
QtyValueFootprintReferences
2RResistor_SMD:R_0603_1608MetricR1, R2
1AD8556ARZLibrary:SOIC127P600X175-8NIC1
1load inLibrary:17345984J1
1main pcbLibrary:load to mainJ2

More from chaxaf/Supersonic-Test-Rocket

2
  • 2 layers36.6 × 34.6 mmNosecone, the printed circuit board in 3D

    Nosecone

    chaxaf/Supersonic-Test-Rocket

    Hardware for EPFL Rocket Team Hermes Supersonic Test Rocket

    22 parts
  • 2 layers40 × 24 mmNosecone, the printed circuit board in 3D

    Nosecone

    chaxaf/Supersonic-Test-Rocket

    Hardware for EPFL Rocket Team Hermes Supersonic Test Rocket

    20 parts

Similar boards

  • 2 layers98 × 27 mmXy limit, the printed circuit board in 3D

    Xy limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    5 parts3.7k
  • 2 layers21 × 33 mm24g2usb pico2w, the printed circuit board in 3D

    24g2usb pico2w

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    5 parts1.7kApache-2.0
  • 2 layers53.2 × 59.6 mmA10 OLinuXino Lime Rev B SHIELD TEMPLATE, the printed circuit board in 3D

    A10 OLinuXino Lime Rev B SHIELD TEMPLATE

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    5 parts1.5k
  • 2 layers30 × 11 mmMain control board servo tester, the printed circuit board in 3D

    Main control board servo tester

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    5 parts1.1k
  • 2 layers78.8 × 35.3 mmKiCadTest, the printed circuit board in 3D

    KiCadTest

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    5 parts915
  • 2 layers50 × 23 mmMiniCircuits LTCC, the printed circuit board in 3D

    MiniCircuits LTCC

    VanceVagell/kv4p-ht

    Open source handheld ham radio project KV4P-HT

    5 parts828GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 light sensor, the printed circuit board in 3D

    L0 light sensor

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    5 parts546MIT

Questions

What parts does the Load cell use?

5 parts, built around the AD8556ARZ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Load cell KiCad files?

From the chaxaf/Supersonic-Test-Rocket repository on GitHub, at the commit this page was made from: the board is hardware/load_cell_pcb/load cell.kicad_pcb and its schematic hardware/load_cell_pcb/load cell.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Load cell design in my own project?

Its repository states no licence, so its author keeps all rights: ask chaxaf before reusing the design.