

ESP32-S2
A New PCB Design for ESP32-S2 Board
- Size
- 27.9 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 64
- Pads
- 201
- Tracks, vias
- 529, 53
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Mar 2021
- Updated
- 21 Mar 2021
Overview
ESP32-S2 is an open-source printed circuit board by chaitravi-ce, from the chaitravi-ce/ESP32-S2_PCB-Design repository on GitHub, published under the MIT licence. It is a 2-layer board of 27.9 × 70 mm with 42 parts on 64 nets, routed with 529 tracks and 53 vias.
It is built around the CH340C, AMS1117-3.3 and L8050QLT1G, with the BAT760-7 and TYPE-C-31-M-12 among its other parts. Its parts include 11 capacitors, 11 resistors, 4 diodes, 4 connectors and 3 ICs. It belongs with the ESP32 boards of this library.
Main components
5CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsL8050QLT1G
SOT-23-55℃~+150℃ 1 NPN 100 150nA 225mW 25V 500mV 5V 800mA NPN SOT-23 Bipolar (BJT) ROHSLeshan Radio (LRC)Bipolar (BJT)BAT760-7
SOD-323Schottky DiodesDOWOTYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
README
README.mdESP32-S2 Hardware Design
This repository contains hardware design files and datasheets for the ESP32-S2. This is an ESP32-S2 based PCB with breakout ports for both USB - Type A and USB - Type C.

Features
- Small form factor of 70mm x 27.9mm
- Uses ESP32-S2-WROOM RF module
- Breakout ports for both USB - Type A and USB - Type C
- Powering modes for the ESP - Either can be used
- USB - A: Using a USB A Male Cable
- USB - C: Using a USB C Male Cable(Typical Mobile charger cable)
- Vin Pin: Supplying this GPIO pin with external 5V
- Can use it as a power/communicating device for a joystick/ game controller.
- Space efficient PCB with integrating majority components in SMD type.
Project Structure
/assets/datasheets - contains datasheets of various components used in the pcb
/assets/references - contains references for the pcb
/assets/schematics - contains schematics of the the pcbTools
To view/modify the files from this repository, install KiCAD from: https://kicad.org
Schematics

Plots
Front side

Back side

Contributors
- Dhairya Shah: Designer
- Chaitravi Chalke: Designer
- Sakshi Chikshe: Designer
- Vedant Paranjape: Mentor
- Omkar Bhilare: Mentor
Future work
To add extra components to the board to deliver better functionality(Eg: Adding OLED)
License
- Distributed under the MIT License.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C2, C4, C5, C6, C7, C9, C11 |
| 6 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R5, R7, R8 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R9, R10, R11 |
| 3 | LED | LED_SMD:LED_0603_1608Metric_Castellated | D2, D3, D4 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R3, R6 |
| 2 | L8050QLT1G | L8050QLT1G:L8050QLT1G | Q1, Q2 |
| 2 | SW_Push | tactile_smd_switch:tactile_smd_switch | SW1, SW2 |
| 1 | buzzard_labels | ||
| 1 | 10 uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 22 uF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | BAT760-7 | BAT-760:SOD2513X120N | D1 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | Conn_01x18_Male | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J3 |
| 1 | Conn_01x22_Male | Connector_PinHeader_2.54mm:PinHeader_1x22_P2.54mm_Vertical | J4 |
| 1 | ESP32-S2-WROOM-ESP32-S2-WROOM | ESP32-S2-WROOM_M22S2H3200PH3Q0:ESP32S2WROOMM22S2H3200PH3Q0 | U1 |
| 1 | LOGO | SRA_Logo:sralogo | G*** |
| 1 | Polyfuse_Small | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | TYPE-C-31-M-12 | USB-TYPE-C:HRO_TYPE-C-31-M-12 | J2 |
| 1 | USB_A | Connector_USB:USB_A_Wuerth_614004134726_Horizontal | J1 |
The 40 most common of 42 parts.
Similar boards
- 2 layers86 × 50 mm

- 2 layers26 × 38 mm

- 4 layers152.5 × 161.6 mm

MB PCB ControladorESP32
Miguel-Barcelos/Electronics-Projects
Este repositório contém projetos de eletrônica, incluindo circuitos eletrônicos, simulações e design de PCBs.
203 parts - 2 layers78.7 × 50.8 mm

- 2 layers35.2 × 51 mm

- 2 layers

- 4 layers62.9 × 88.6 mm

Bit block
Citrullin/Sovereign_Bunny_Stack
From web 3 unicorn fantasy to federated web 2.5 reality.
169 parts4 - 4 layers50.8 × 81.3 mm

Esp32-s3-with ken interface
kawashimaken/general-purpose-ken-interface
A modular, multi-MCU prototyping platform with a unified pin-assignment standard and horizontally-stackable expansion boards.
41 parts3MIT
Questions
How big is the ESP32-S2 PCB?
It measures 27.9 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32-S2 use?
42 parts, built around the CH340C, AMS1117-3.3, L8050QLT1G and BAT760-7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32-S2 KiCad files?
From the chaitravi-ce/ESP32-S2_PCB-Design repository on GitHub, at the commit this page was made from: the board is ESP32-S2/ESP32-S2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32-S2 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).