Skip to the content
2 layers98.8 × 51.6 mmCat feeder KiCad, the printed circuit board in 3D

Cat feeder KiCad

Celinalu/Cat_foodfeeder

Case: For the case, I used Fusion 360. Before I made my case, I did a lot of research on what other people made.

Size
98.8 × 51.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
22
Nets
52
Pads
135
Tracks, vias
277, 28
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
26 Apr 2026
Updated
7 Jun 2026

Overview

Cat feeder KiCad is an open-source printed circuit board by Celinalu, from the Celinalu/Cat_foodfeeder repository on GitHub. It is a 2-layer board of 98.8 × 51.6 mm with 22 parts on 52 nets, routed with 277 tracks and 28 vias.

It is built around the ESP32-S3-WROOM-1-N8, LD1117V33 and PCF85263AT/AJ. Its parts include 6 capacitors, 4 resistors, 3 ICs, 3 connectors and 1 diode. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

Cat Feeder

About

This cat feeder, as the name implies, is a food dispenser for my cat. It is an automatic feeder that will dispense food two times a day. It runs off an ESP32S3 and is paired with an RTC that controls the feeding time. The PCB is also connected to pins that will attach itself to a servo motor to complete the action of turning the door to dispense food. The power source of this feeder is from the USBC port connected to the PCB, and the USBC will get electricity from outside. Screenshot 2026-05-31 201840 Screenshot 2026-06-06 190411

Parts explained

PCB: I used Kicad to create the schematic and PCB. I took a look online to see what the main components were that other people used. And I found that it consisted of an MCU, a motor, a clock, and a display for the clock, so that is what I based my schematic on. I connected my ESP32S3 to a clock, and I added pins on my PCB to connect to a display as well as a servo motor. For the clock, I also added a small battery so it can run even if the feeder gets disconnected from power for a bit. There is also a button on the PCB meant for resetting the machine if that ever needs to be done.

Case: For the case, I used Fusion 360. Before I made my case, I did a lot of research on what other people made. I found that there were two main disperser mechanisms that are commonly used: An arger and an open and closed mechanism (I hope that is understandable language). I ended up using the open and closed door mechanism. Tweaking it slightly by making my door more like a turning door. Before I was worried about the weight of the kibble, but the whole dispenser isn't that big so there isn't a ton of kibble in there; the weight shouldn't be much of an issue. Other than that, everything else is pretty straightforward. There are two main spaces in the feeder. The top is for the PCB, while the bottom is kibble.

Firmware: I tried to make it as simple as possible. Since the main purpose of the firmware is to program the times that the feeder will dispense food and let the servo know when it moves. I don't know if my firmware will even work yet, but it didnt give me any issues so I'll have to see if it works after I make the feeder.

How to use

The feeder has many lid-like tops, and the only screws in the whole machine are for the PCB to attach to the feeder. So the main thing that needs to be done is every couple of days to remove the top compartment and add kibble into it. I didn't use many screws because I thought it would be quite inconvenient to have to unscrew something every other day, since this whole machine is supposedly allowing you to become more lazy. Other than adding kibble, you don't really have to do anything!

Why I made this

I decided to do this project since I thought that this would be a fun and useful project that I could actually use in my house, so it wouldn't become an object collecting dust. Compared to other machine-like projects, this one had relatively not amount of componnets, so it was still within my abilities to figure this project out.

Zine

Screenshot 2026-06-07 113851

Parts

22
QtyValueFootprintReferences
310uFCapacitor_SMD:C_0805_2012MetricC1, C2, C3
34.7KResistor_SMD:R_0805_2012MetricR6, R7, R8
2100nFCapacitor_SMD:C_0805_2012MetricC4, C7
1100ΩResistor_SMD:R_0805_2012MetricR5
11N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD2
11uFCapacitor_SMD:C_0805_2012MetricC8
1Battery_CellBattery:BatteryHolder_Keystone_3034_1x20mmBT2
1CrystalCrystal:Crystal_SMD_0603-2Pin_6.0x3.5mmY1
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1LD1117V33Package_TO_SOT_THT:TO-220-3_VerticalU4
1OLED connectorConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1PCF85263ATPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU5
1Reset buttonButton_Switch_THT:SW_PUSH_6mmSW2
1Servo motor connectorConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1USB_C_Receptacle_USB2.0_14PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J3

The 20 most common of 22 parts.

Similar boards

  • 2 layers38 × 200 mmSPACEDOS02A PCB01A, the printed circuit board in 3D

    SPACEDOS02A PCB01A

    UniversalScientificTechnologies/SPACEDOS02

    Solid-state PIN diode dosimeter for manned spacecraft. Liulin detector replacement.

    120 parts8GPL-3.0
  • 2 layers136.2 × 85.9 mmBATDATUNIT01, the printed circuit board in 3D

    BATDATUNIT01

    mlab-modules/BATDATUNIT01

    Multiple parallel Li-ion 18650 battery cell module with BMS and data storage with MCU control.

    225 parts5GPL-3.0
  • 2 layers93.5 × 48.2 mmSPACEDOS01, the printed circuit board in 3D

    SPACEDOS01

    UniversalScientificTechnologies/SPACEDOS01

    Silicon diode dosimeter optimized for spacecraft dosimetry

    92 parts5GPL-3.0
  • 2 layers80.8 × 101.1 mmDATALOGGER01, the printed circuit board in 3D

    DATALOGGER01

    mlab-modules/DATALOGGER01

    Universal Arduino based data logger to SDcard.

    90 parts1GPL-3.0
  • 4 layers95 × 50 mmVFD tool, the printed circuit board in 3D

    VFD tool

    Haxintosh/VFD-tool

    A modular multitool designed for engineers with a VFD screen (WIP!!!!!!!)

    177 partsMIT
  • 4 layers89.9 × 88.8 mmBigboard, the printed circuit board in 3D

    Bigboard

    mincrmatt12/MWatch

    pebble-style smartwatch os&hardware

    110 parts
  • 4 layers90.9 × 50.3 mmUSTSIPIN02, the printed circuit board in 3D

    USTSIPIN02

    ust-modules/USTSIPIN02

    Silicon diode dosimeter and spectrometer.

    174 partsGPL-3.0
  • 4 layers243.8 × 243.8 mmCm4 matx, the printed circuit board in 3D

    Cm4 matx

    EDA-bench/eda-bench

    Execution-based benchmark for open-book KiCad PCB reconstruction agents

    214 parts4

Questions

How big is the Cat feeder KiCad PCB?

It measures 98.8 × 51.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cat feeder KiCad use?

22 parts, built around the ESP32-S3-WROOM-1-N8, LD1117V33 and PCF85263AT/AJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cat feeder KiCad KiCad files?

From the Celinalu/Cat_foodfeeder repository on GitHub, at the commit this page was made from: the board is Cat_feeder_KiCad/Cat_feeder_KiCad.kicad_pcb and its schematic Cat_feeder_KiCad/Cat_feeder_KiCad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cat feeder KiCad design in my own project?

Its repository states no licence, so its author keeps all rights: ask Celinalu before reusing the design.