

Anndroid
You know the new series Anndroid, well its that but in real life **ONLY USE IF YOU KNOW WHAT YOU ARE DOING!!!*
- Size
- 164.6 × 40 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 14
- Pads
- 255
- Tracks, vias
- 53, 3
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 21 Aug 2026
- Updated
- 21 Aug 2026
Overview
Anndroid is an open-source printed circuit board by catsandgaming, from the catsandgaming/anndroid-robot repository on GitHub. It is a 2-layer board of 164.6 × 40 mm with 24 parts on 14 nets, routed with 53 tracks and 3 vias.
It is built around the PAM8302AASCR. Its parts include 5 capacitors, 3 resistors, 1 IC and 1 crystal.
Main components
1README
README.md⚠️ BEFORE YOU EVEN START ⚠️
DO NOT GO ON UNLESS YOU ARE A PROFESSIONAL AND YOU KNOW WHAT YOU ARE DOING!
Animatronic Figure Build
Overview
Full-scale animatronic figure project — a 3D-printed shell over an internal aluminum skeleton, with servo-driven arms, neck, jaw, and eyes, TTS-based speech, and onboard logging. Controlled by a Raspberry Pi 5 + ESP32/Arduino Mega pairing, with a PCA9685 driving all servo channels.
Specs
- Height: 5'7" (170 cm)
- Skeleton: aluminum T-slot extrusion + tube, bearing-mounted joints
- Shell: PETG/ASA structural panels, resin face/hands, silicone skin overlay
- Motion: neck (pan/tilt), eyes (pan/tilt + eyelids), jaw (audio-driven), arms (shoulder/elbow/wrist, 2 DOF+ per side)
- Voice: TTS engine (generic/licensed voice — no real-person voice cloning)
- Compute: Raspberry Pi 5 (8GB) + ESP32/Mega for real-time servo timing
- Storage/logging: onboard SSD, SQLite/CSV logs of servo state, audio triggers, errors, uptime
Documentation
See the project docs for full detail:
- 01_System_Architecture_Diagram
- 02_Mechanical_CAD_Models
- 03_Bill_of_Materials
- 04_Electronics_and_Wiring
- 05_Component_Datasheets
- 06_Control_Theory
- 07_Operating_Software
- 08_Source_Code
- 09_Calibration_Logs
KiCad Symbol Libraries
This project uses two KiCad symbol/footprint libraries, covering the main compute module and the microphone module. Both follow the same general install pattern: add the library file(s) via Preferences > Manage Symbol Libraries... (and Manage Footprint Libraries... where a footprint is included), then verify in the Symbol/Footprint Editor before use.
| Library | Covers | KiCad Version |
|---|---|---|
| Raspberry Pi Compute Module | CM4, CM5 (symbols only) | KiCad 9 |
| INMP441ACEZ-R7 | Digital MEMS microphone (symbol + footprint) | KiCad 6+ |
1. Raspberry Pi Compute Module Library
Schematic symbol libraries (.kicad_sym) for the Raspberry Pi Compute
Module series (CM4 and CM5), for KiCad 9. https://github.com/Supercookiegaming/Raspberry-Pi-Compute-Module-KiCad
📦 Contents
| File Name | Description |
|---|---|
Raspberry-Pi-CM4.kicad_sym | Schematic symbols for Raspberry Pi Compute Module 4 |
Raspberry-Pi-CM5.kicad_sym | Schematic symbols for Raspberry Pi Compute Module 5 |
⚙️ Installation Guide
- Open KiCad 9.
- From the main window, select Preferences > Manage Symbol Libraries...
- Select either the Global Libraries tab (available across all projects) or Project Specific Libraries tab.
- Click the
+(Add existing library) button at the bottom of the table. - Configure the library entries:
- Nickname:
Raspberry-Pi-CM4 - Library Path: Browse to and select
Raspberry-Pi-CM4.kicad_sym - Plugin Type:
KiCad
- Nickname:
- Repeat for the CM5 library:
- Nickname:
Raspberry-Pi-CM5 - Library Path: Browse to and select
Raspberry-Pi-CM5.kicad_sym - Plugin Type:
KiCad
- Nickname:
- Click OK to save and apply settings.
🛠️ Usage in Schematic Editor
- Open your project's Schematic Editor (
.kicad_sch). - Press
Aor click Add Symbol on the right toolbar. - In the search box, filter by
Raspberry-Pi-CM4orRaspberry-Pi-CM5. - Select your module variant and place it on the schematic canvas.
🚨 Required Environment Path Setup
For associated footprint assignments and 3D models to link correctly when updating your PCB layout, ensure the base environment variable is configured:
- Go to Preferences > Configure Paths...
- Add an environment variable:
- Name:
KICAD9_USER_RPICM_REPO_DIR - Path: Absolute path to the repository root directory (e.g.,
/path/to/Raspberry-Pi-Compute-Module-KiCad-main)
- Name:
- Click OK.
📄 License & Attribution
Refer to the root LICENSE file for usage and distribution guidelines.
2. INMP441ACEZ-R7 Microphone Library
It is easy, the raw files are unzipped in equipment but to make it easier i have provided both, we reccomend using the zip https://github.com/catsandgaming/anndroid-robot/blob/main/Equipment/INMP441ACEZ-R7.zip _ Official schematic symbol and PCB footprint library files for the INMP441ACEZ-R7 digital MEMS microphone, for KiCad 6 and newer.
⚠️ Important Download & Unzip Instructions
Do NOT rename the extracted folder.
Structure: Keep the internal file structure completely intact (including .pretty, .kicad_mod, and .kicad_sym files/folders).
Note: Renaming the root extracted folder or altering internal directory paths will break absolute references and lead to footprint import errors in KiCad.
🛠️ KiCad Import Guide (V6 and Later)
Import Symbol (.kicad_sym)
- Extract the contents of your downloaded
*.zipfile. - Launch KiCad and navigate to Preferences > Manage Symbol Libraries...
- Select the Global Libraries tab (or Project Specific Libraries depending on your workflow).
- Click Browse Libraries (the small folder icon at the bottom of the table).
- Select the
*.kicad_symfile from your extracted directory and click Open. - Verify the library appears in the table list, then click OK.
- To verify, open the Symbol Editor, search for
INMP441ACEZ-R7in the filter field, and double-click to view the component.
Import Footprint (.pretty)
- Go to Preferences > Manage Footprint Libraries...
- Select the Global Libraries tab.
- Click Browse Libraries (the folder icon at the bottom).
- Browse to and select the
.prettyfolder inside the extracted directory, then click Open. - Click OK to save and apply settings.
🔍 Verification Checklist
- Extracted folder name was not altered.
- Symbol displays correctly in the Symbol Editor.
- Footprint appears under library filter in Footprint Editor.
- Pin-out numbers on the schematic symbol match the physical pads on the footprint.
Installation
TBC — full setup and assembly instructions will be added in the coming months as the build progresses.
Notes
- Likeness and voice: if this figure depicts a real, identifiable person and is intended for anything beyond private personal use, obtain permission for likeness and voice use.
- This is a prototype-stage project; specs and BOM quantities may change as parts are bench-tested.
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100 | 0805-NO | R1, R2 |
| 2 | 1uF | 0805-NO | C1, C2 |
| 2 | 220pF | 0805-NO | C4, C5 |
| 2 | FIDUCIAL"" | FIDUCIAL_1MM | FID1, FID2 |
| 2 | Ferrite | _0805 | FB1, FB2 |
| 2 | MOUNTINGHOLE2.0 | MOUNTINGHOLE_2.0_PLATED | U$10, U$11 |
| 1 | SYMBOL_MINUS | U$4 | |
| 1 | SYMBOL_PLUS | U$3 | |
| 1 | PCBFEAT-REV-040 | U$6 | |
| 1 | ADAFRUIT_3.5MM | U$5 | |
| 1 | 1X05_ROUND_70 | JP1 | |
| 1 | TERMBLOCK_1X2-3.5MM | X1 | |
| 1 | 10K | 0805-NO | R3 |
| 1 | 10K trim | TRIMPOT_BOURNS_3303W | VR1 |
| 1 | 10uF | 0805-NO | C3 |
| 1 | PAM8302AASCR | MSOP8_0.65MM | U1 |
The 22 most common of 24 parts.
Similar boards
- 4 layers121.9 × 44.4 mm

- 4 layers25.3 × 35.1 mm

Agb hifi audio pcb
cajunpanda/gameboy-hifi-audio
A HiFi audio mod for various Game Boy models
66 parts25MIT - 2 layers81 × 55 mm

- 4 layers54.7 × 78.5 mm

DisplayModule PONSv71
MasaoC/GPS-TFT-Map_PONS
鳥人間コンテストに特化したGNSS誘導システム。人力飛行機のパイロットが使いやすいことを目標にした航法装置です。ハードとソフトをオープンソースで開発しています。
151 parts14MIT - 2 layers82.5 × 136.7 mm

Gameboy dmg
alxhoff/gameboy-dmg-pcb
PCB for Gameboy DMG with audio and GPIO expander to provide I2C interface to push buttons
95 parts4GPL-3.0 - 4 layers182 × 150 mm

- 2 layers58 × 44 mm

Button
birkenfeld/stm_button_rust
Using nightly Rust and cargo, just do a cargo build --release.
40 parts3 - 4 layers70 × 90 mm

Questions
How big is the Anndroid PCB?
It measures 164.6 × 40 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Anndroid use?
24 parts, built around the PAM8302AASCR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Anndroid KiCad files?
From the catsandgaming/anndroid-robot repository on GitHub, at the commit this page was made from: the board is Equipment/Anndroid/Anndroid.kicad_pcb and its schematic Anndroid.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Anndroid design in my own project?
Its repository states no licence, so its author keeps all rights: ask catsandgaming before reusing the design.