
Panel
calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

High-flexibility, low-cost mechatronics controller for 3D printers
Driver tmc2160 is an open-source printed circuit board by calithameridi, from the calithameridi/corevus repository on GitHub. It is a 4-layer board of 30 × 29 mm with 71 parts on 51 nets, routed with 444 tracks and 147 vias.
It is built around the TMC2160-TA and BAV99S. Its parts include 21 capacitors, 12 resistors, 8 transistors, 4 diodes and 1 IC.
Copyright 2024 by meridi (myself), all rights reserved until I decide on a suitable license
Corevus-G v0.6 printer mainboards are available for evaluation and beta testing. Join the discord:
discord (dot) gg (slash) W 5 m a f w 2 k Y h. See the Corevus-G v0.6 manual here for more information.
High performance, low-ish price control board for 3D printers.

(For older hardware releases, also see the CvG v0.4 manual)
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 30N06 | corevus:MOSFET_DFN8 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 5 | 1μF 25V | AlphaLib:0402C | C1, C8, C9, C10, C11 |
| 4 | 1nF 100V | PCM_ME_passives:0402C | C16, C17, C18, C19 |
| 4 | 30Ω@100MHz | Resistor_SMD:R_0805_2012Metric | FB1, FB2, FB3, FB4 |
| 4 | 47Ω | AlphaLib:0402R | R8, R9, R11, R12 |
| 3 | 1μF | AlphaLib:0402C | C4, C6, C13 |
| 3 | 1μF 100V | Capacitor_SMD:C_1206_3216Metric | C12, C14, C15 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP2, TP3, TP4 |
| 2 | 100nF 100V | AlphaLib:0402C | C2, C7 |
| 2 | 10kΩ | AlphaLib:0402R | R2, R3 |
| 2 | 1nF | PCM_ME_passives:0402C | C20, C21 |
| 2 | 1µF | AlphaLib:0402C | C3, C5 |
| 2 | 4.7kΩ | AlphaLib:0402R | R1, R20 |
| 2 | 50mΩ | Resistor_SMD:R_1206_3216Metric | R10, R13 |
| 2 | BAV99S | Package_TO_SOT_SMD:SOT-363_SC-70-6 | D3, D4 |
| 2 | GND | corevus:LGA_Land_2.5mm | T5, T12 |
| 1 | 10kΩ 3950K | AlphaLib:0402R | TH1 |
| 1 | 12V | corevus:LGA_Land_2.5mm | T3 |
| 1 | 1kΩ | AlphaLib:0402R | R16 |
| 1 | 1Ω | AlphaLib:0402R | R4 |
| 1 | CS0 | corevus:LGA_Land_2.5mm | T10 |
| 1 | DIAG | corevus:LGA_Land_2.5mm | T17 |
| 1 | DIR | corevus:LGA_Land_2.5mm | T13 |
| 1 | EN | corevus:LGA_Land_2.5mm | T14 |
| 1 | Gnd | corevus:MountingHole_M3_Driver | H2 |
| 1 | Green | PCM_ME_passives:0402LED | D2 |
| 1 | Red | PCM_ME_passives:0402LED | D1 |
| 1 | SCK | corevus:LGA_Land_2.5mm | T4 |
| 1 | SDI | corevus:LGA_Land_2.5mm | T6 |
| 1 | SDO | corevus:LGA_Land_2.5mm | T7 |
| 1 | STEP | corevus:LGA_Land_2.5mm | T11 |
| 1 | TMC2160 | corevus:TMCx160 | U1 |
| 1 | Therm | corevus:LGA_Land_2.5mm | T9 |
| 1 | ToolingHole | corevus:ToolingHole | H3 |
| 1 | VCC | corevus:LGA_Land_2.5mm | T8 |
| 1 | VM | corevus:MountingHole_M3_Driver | H1 |
| 1 | XH | corevus:XH_1x04_SMD_Vertical | J1 |

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers

calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers


hasenbanck/heteromycin
A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC



matthewlai/ESP32Stepper
This is the PCB design and firmware for a Trinamic TMC2590-based stepper motor driver with an ESP32 microcontroller.



MouseBiteLabs/Super-Game-Boy-Plus
A replacement circuit board for improving the Super Game Boy, or for creating a standalone Game Boy game for the SNES.
It measures 30 × 29 mm and has 4 copper layers, 1.6 mm thick.
71 parts, built around the TMC2160-TA and BAV99S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the calithameridi/corevus repository on GitHub, at the commit this page was made from: the board is hardware/motor_drivers/driver-tmc2160/driver-tmc2160.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask calithameridi before reusing the design.