
A VideoBoard
c0pperdragon/A-VideoBoard
FPGA board to create a component video signal for vintage computers.

FPGA board to create a component video signal for vintage computers.
C64board is an open-source printed circuit board by c0pperdragon, from the c0pperdragon/A-VideoBoard repository on GitHub, published under the MIT licence. It is a 2-layer board of 24.4 × 53.3 mm with 12 parts on 63 nets, routed with 397 tracks and 45 vias.
It is built around the MIC5504-3.3YM5. Its parts include 5 capacitors, 5 ICs, 1 resistor and 1 connector. It belongs with the fPGA and programmable logic and retro computing and games boards of this library.
A small FPGA board with a component video interface to directly drive an analog monitor or TV input. Its main purpose is to create component video / RGB mods of vintage home computers and consoles or to provide video output for hobby projects.
It consists of the purest minimum parts necessary to have a multi-purpose FPGA combined with a simple way to generate a YPbPr signal. After much research I finally settled on a cheap MAX 10 device in a TQFP-144 package which I can solder by hand (barely). The rest of the parts are pretty cheap and quite easy to solder.
To interface any of the vintage systems to the A-Video Board, level shifters are necessary to translate the 5 volt to 3.3 volt for the FPGA input pins. These level shifters can be implemented in a system specific daughter board that can be stacked on top of the A-Video board. Any such interface board can probably be implemented in a simple single-sided wide-pitch PCB that can be even home-etched with some experience.
Currently I have built applications of the A-Video board for

The board has these main parts
and various supporting passive components, mainly decoupling, filtering and pull-ups.
It has the following connectors:
If you plan to use an A-Video board, feel free to contact me for assistance:
reinhard.grafl (at) aon.at
Maybe I will either have some spare PCBs I could send you to populate yourself,
or even provide you with a fully assembled board for the cost of the parts and shipping.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C4, C5 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2 |
| 2 | LVC245 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U4, U5 |
| 1 | 100Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J1 |
| 1 | LVC257 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U3 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | VIC-II | footprints:socket_embedded_40pin | U1 |

c0pperdragon/A-VideoBoard
FPGA board to create a component video signal for vintage computers.

c0pperdragon/A-VideoBoard
FPGA board to create a component video signal for vintage computers.

c0pperdragon/A-VideoBoard
FPGA board to create a component video signal for vintage computers.


tmk/USB2USB_Converter
USB to USB keyboard protocol converter supported by TMK keyboard firmware

kiu/lofence
LoFence is a LoRaWAN capable IoT electric fence monitoring system running on the The Things Network.


nkrackow/SingularitySurfer-FPGA-Lock-In-Amplifier
Repository for the development of an FPGA based DSP Lock-In Amplifier

AndersBNielsen/PhaseLatchMini
High-rate continuous streaming of interleaved dual ADC (I/Q) samples over USB Full‑Speed (FS) using only the built‑in CDC class on an STM32F103C8 ("Blue Pill" style) board.

Badbird5907/thermal-camera
My design of a cheap and affordable thermal camera

felixheld/qspimux
QSPI flash multiplexer - connect a SPI NOR flash to either an embedded system or a programmer for remote firmware tests
It measures 24.4 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
12 parts, built around the MIC5504-3.3YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the c0pperdragon/A-VideoBoard repository on GitHub, at the commit this page was made from: the board is c64mod/c64board/c64board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).