

HT 1590BB
Tremolo effect for guitar designed to fit into Hammond 1590BB enclosure
- Size
- 111 × 85 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 52
- Pads
- 176
- Tracks, vias
- 283, 0
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 15 Jun 2022
- Updated
- 15 Jun 2022
Overview
HT 1590BB is an open-source printed circuit board by brumpan, from the brumpan/HarmonicTremolo_V02 repository on GitHub. It is a 2-layer board of 111 × 85 mm with 71 parts on 52 nets, routed with 283 tracks and 0 vias.
It is built around the LM324 and LM358. Its parts include 34 resistors, 11 capacitors, 5 ICs, 4 diodes and 2 connectors.
Main components
2Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 22k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R6, R9, R11, R17, R18, R31, R32 |
| 6 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4, R5, R20, R23, R25, R26 |
| 6 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R10, R12, R28, R29, R30, R34 |
| 5 | 1Meg | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R7, R13, R14, R16 |
| 4 | Pin_D1.0mm_L10.0mm | Connector_Pin:Pin_D1.0mm_L10.0mm | DRL1, DRL1, DRL2, DRL3 |
| 2 | 100n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C6, C11 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R21, R33 |
| 2 | 18n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C3, C4 |
| 2 | 4.7u | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C1, C2 |
| 2 | 47k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R8, R27 |
| 2 | VTL5C | Vactrol:Vactrol | U4, U5 |
| 1 | 100u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C7 |
| 1 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C8 |
| 1 | 1N4001 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 1u | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C9 |
| 1 | 2.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R15 |
| 1 | 22n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C10 |
| 1 | 250k | 1590BB:Alpha_16mm_PCB_RA_Dual | RV1 |
| 1 | 27k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R19 |
| 1 | 4.7k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R22 |
| 1 | 470k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R24 |
| 1 | 47n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C5 |
| 1 | 9V | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | 9V1 |
| 1 | FX_IN | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | FX_IN |
| 1 | FX_OUT | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | FX_OUT |
| 1 | GND | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | GND |
| 1 | INPUT | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | INPUT |
| 1 | INPUT_JACK | Connector_Audio:Jack_6.35mm_Neutrik_NMJ4HCD2_Horizontal | J7 |
| 1 | LED | LED_THT:LED_D5.0mm | D2 |
| 1 | LED1 | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | LED1 |
| 1 | LED2 | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | LED2 |
| 1 | LM324 | Package_DIP:DIP-14_W7.62mm_Socket | U2 |
| 1 | LM358 | Package_DIP:DIP-8_W7.62mm_Socket | U3 |
| 1 | Mix | 1590BB:Alpha_16mm_PCB_RA | RV3 |
| 1 | OUPUT_JACK | Connector_Audio:Jack_6.35mm_Neutrik_NMJ4HCD2_Horizontal | J8 |
| 1 | OUTPUT | Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mm | OUTPUT |
| 1 | Q_NJFET_DSG | Package_TO_SOT_THT:TO-92_Inline_Wide | Q1 |
| 1 | Rate | 1590BB:Alpha_16mm_PCB_RA | Rate1 |
| 1 | TL074 | Package_DIP:DIP-14_W7.62mm_Socket | U1 |
| 1 | Waveform | 1590BB:Alpha_16mm_PCB_RA | Waveform1 |
Similar boards
- 2 layers

- 2 layers99.7 × 49.5 mm

Opamp vos
cellularmitosis/opamp-vos
A board to measure the Vos (input offset voltage) of op amps.
99 parts1MIT - 2 layers55 × 485 mm

- 4 layers150 × 100 mm

- 2 layers190 × 109 mm

IOB v3.2.1
ADFTech/xtec-uc-ip-main-pcb
KiCad hardware repo for the UC-IP main PCB (currently: IOB board family). This README documents the review-and-release process used to get a schematic/PCB change from an engineer's desk to fabrication.
538 parts - 2 layers135.6 × 85.3 mm

- 2 layers83.5 × 83 mm

- 2 layers99.5 × 99.5 mm

Carico elettronico
dario0603/electronic_load
Un progetto open-source per la progettazione e simulazione di un Carico Elettronico Bipolare (Electronic Load), ideato per il test e la caratterizzazione di alimentatori, batterie e circuiti di potenza.
92 parts
Questions
How big is the HT 1590BB PCB?
It measures 111 × 85 mm and has 2 copper layers, 1.6 mm thick.
What parts does the HT 1590BB use?
71 parts, built around the LM324 and LM358. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HT 1590BB KiCad files?
From the brumpan/HarmonicTremolo_V02 repository on GitHub, at the commit this page was made from: the board is HT/HT_1590BB/HT_1590BB.kicad_pcb and its schematic HT/HT_1590BB/HT_1590BB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the HT 1590BB design in my own project?
Its repository states no licence, so its author keeps all rights: ask brumpan before reusing the design.