Skip to the content
2 layers102.9 × 69.9 mmController T41 rev0.2, the printed circuit board in 3D

A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

Size
102.9 × 69.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
58
Nets
136
Pads
407
Tracks, vias
507, 59
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
2 Nov 2020
Updated
22 Jan 2022

Overview

Controller T41 rev0.2 is an open-source printed circuit board by brianamos1, from the brianamos1/DuotrigesimalWS2811 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 102.9 × 69.9 mm with 58 parts on 136 nets, routed with 507 tracks and 59 vias.

It is built around the 74HCT245, TEENSY 4.1 and AMS1117-5.0, with the B5819W among its other parts. Its parts include 33 resistors, 6 ICs, 4 connectors, 3 capacitors and 2 diodes. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

4

README

README.md

DuotrigesimalWS2811

A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

This board interfaces with a Teensy 4.1, and is designed to use the OctoWS2811 library to drive up to 32 strings of LEDS.

Version 0.2 is designed to use the Amphenol RJHSE508004-ND, which is a four port RJ45 jack. Version 0.2a uses the Adam Tech MTJG-4-88GX1-FSB, which is a less expensive and more readily available alternative.

The 2x3 pin that connects the board to the Teensy 4.1's ethernet pins is available on digikey and mouser, however is easier to source from PJRC when purchasing the Teensy 4.1. If you want the teensy to be removable, PJRC is the recommended source for that connector. If you're going to solder the T4.1 to this board, then it doesn't matter the source for the pins. ‎

Alt text

Boards are available for purchase at https://www.tindie.com/products/25767/

Parts

58
QtyValueFootprintReferences
32100ohmResistor_SMD:R_1206_3216MetricR2, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24 +16
43mmMountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
474HCT245Package_SO:SOIC-20W_7.5x12.8mm_P1.27mmU3, U4, U5, U6
210uCapacitor_SMD:C_1206_3216MetricC1, C2
28P8C_x4Controller_T41_rev0.2:RJ45_Amphenol_RJHSE508004-ND‎J1, J2
10.1uFCapacitor_SMD:C_0805_2012MetricC3
1100@100MHz GZ2012D101TFInductor_SMD:L_0805_2012MetricFB1
12k2Resistor_SMD:R_0805_2012MetricR1
1500mAFuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolderF1
1AMS1117-5.0Package_TO_SOT_SMD:SOT-223-3_TabPin2U2
1B5819WDiode_SMD:D_SOD-123D1
1LOGOController_T41_rev0.2:logoG***
1RJ45_LEDConnector_RJ:RJ45_Cetus_J1B1211CCD_HorizontalJ4
1Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_HorizontalJ3
1Teensy4.1teensy:Teensy41U1
1redLED_SMD:LED_0603_1608MetricD2

The 55 most common of 58 parts.

More from brianamos1/DuotrigesimalWS2811

4
  • 2 layers102.9 × 69.9 mmController T41 rev0.3, the printed circuit board in 3D

    Controller T41 rev0.3

    brianamos1/DuotrigesimalWS2811

    A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

    56 parts14GPL-3.0
  • 2 layers102.9 × 69.9 mmController T41 rev0.2a, the printed circuit board in 3D

    Controller T41 rev0.2a

    brianamos1/DuotrigesimalWS2811

    A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

    55 parts14GPL-3.0
  • 2 layers38 × 38.1 mmSplitter, the printed circuit board in 3D

    Splitter

    brianamos1/DuotrigesimalWS2811

    A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

    12 parts14GPL-3.0
  • 2 layers38 × 38.1 mmSplitter, the printed circuit board in 3D

    Splitter

    brianamos1/DuotrigesimalWS2811

    A board for driving 32 strings of pixels from a Teensy 4.1. Similar to the OctoWS2811, but with 32 outputs.

    11 parts14GPL-3.0

Similar boards

  • 2 layers112.3 × 136.7 mmPCB 2, the printed circuit board in 3D

    PCB 2

    KomplexKapharnaum/LEDcurtain_hardware

    LEDcurtain_hardware

    117 parts1GPL-3.0
  • 2 layers340 × 100 mmTeensy step sequencer, the printed circuit board in 3D

    Teensy step sequencer

    dwmorrin/teensy-step-sequencer

    hardware-based step sequencer using the Teensy 4.1 microcontroller

    151 parts
  • 2 layers150 × 95 mmRazorBoard, the printed circuit board in 3D

    RazorBoard

    stefanodemartini/RazorGauge

    RazorGauge is a line-diameter measurement and fly-line design project. This repository contains the firmware, Windows desktop application, shared physics library, CLI, and the hardware design files.

    81 parts
  • 4 layers42.2 × 101.8 mmDatalogger PCB, the printed circuit board in 3D

    Datalogger PCB

    uwp-sammckee/DataLogger

    PACKET BREAKDOWN: 0-roll\ 1-pitch\ 2-yaw\ 3-alitude\ 4-pressure\ 5-temperature\ 6-accX\ 7-accY\ 8-accZ\ 9-gyroX\ 10-gyroY\ 11-gyroZ\ 12-time\ 13-placeholder\ 14-placeholder\ 15-placeholder

    54 parts1
  • 2 layers148.8 × 92.6 mmTeensy 16, the printed circuit board in 3D

    Teensy 16

    kitspace-test-repos/kicad6-file-collection

    92 partsMIT
  • 2 layers52.9 × 63 mmSACRED PCB, the printed circuit board in 3D

    SACRED PCB

    valleyquail/WormMQP

    Repository for the code to test and run the WormBot MQP at WPI 2024-25

    20 parts
  • 2 layers100 × 100 mmHeatplate v1.1, the printed circuit board in 3D

    Heatplate v1.1

    DerSpatz/PCB-reflow-solder-heat-plate

    hardware design for a PCB reflow solder heat plate

    57 parts179MIT

Questions

How big is the Controller T41 rev0.2 PCB?

It measures 102.9 × 69.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Controller T41 rev0.2 use?

58 parts, built around the 74HCT245, TEENSY 4.1, AMS1117-5.0 and B5819W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Controller T41 rev0.2 KiCad files?

From the brianamos1/DuotrigesimalWS2811 repository on GitHub, at the commit this page was made from: the board is TPP-0.2/Controller_T41_rev0.2.kicad_pcb and its schematic Splitter-0.1/splitter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Controller T41 rev0.2 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).