Skip to the content
2 layers37 × 15 mmCanTactDist, the printed circuit board in 3D

A 3D printer tool head controller board

Size
37 × 15 mm
Copper layers
2
Thickness
1.6 mm
Parts
41
Nets
23
Pads
140
Tracks, vias
285, 27
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
25 Mar 2020
Updated
10 Dec 2022

Overview

CanTactDist is an open-source printed circuit board by bondus, from the bondus/KlipperToolboard repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 37 × 15 mm with 41 parts on 23 nets, routed with 285 tracks and 27 vias.

It is built around the SN65HVD230D, USBLC6-2SC6 and XC6206P332MR. Its parts include 9 capacitors, 9 resistors, 4 ICs, 4 diodes and 3 connectors. It belongs with the robots and motor control boards and the STM32 boards of this library.

Main components

3

README

README.md

Huvud 3D Printer toolhead board

A very small 3D printer board for use on a direct drive toolhead. It is designed to be used with Klipper firmware. Klipper has the awesome feature to be able to use multiple MCUs connected to the host over a (relatively) high latency connection. Using CAN bus it is possible to chain many boards using just a pair of twisted wires and power. A good solution for multiple head 3D printers.

Image of Board

Features:

  • CAN bus.
  • One TMC2209 stepper driver for the extruder
  • Two MOSFETs for fans
  • One big MOSFET for the hotend heater
  • Thermistor input
  • Support for an endstop (or filament runout sensnor)
  • STM32F103 72Mhz 32bit ARM MCU
  • USB, for flashing firmware

Main power is 12-24V. 24V is preferred to keep the currents low

All done in KiCad and open source.

If you are interesting in helping out, testing or eventually using this board feel free to contact me at glpontus@gmail.com.

Documentation


Buy it at:


Read more about the project activites over at hackaday: https://hackaday.io/project/174429-huvud-a-3d-printer-tool-head-controller-board


Parts

41
QtyValueFootprintReferences
10TestPointTestPoint:TestPoint_Pad_D1.0mmBOOT0, CANH1, CANL1, GND1, GND3, NRST1, SWCLK1, SWIO1, V5, V33
50.1uFCapacitor_SMD:C_0402_1005MetricC10, C17, C18, C19, C28
410kResistor_SMD:R_0402_1005MetricR1, R21, R22, R23
32.2kResistor_SMD:R_0402_1005MetricR2, R3, R20
222pFCapacitor_SMD:C_0402_1005MetricC26, C29
24.7uFCapacitor_SMD:C_0402_1005MetricC2, C3
2LEDGRLED_SMD:LED_0603_1608MetricD1, D5
1120Resistor_SMD:R_0603_1608MetricR4
11kResistor_SMD:R_0402_1005MetricR6
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ4
1Conn_01x03TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_HorizontalJ1
1LEDREDLED_SMD:LED_0603_1608MetricD8
1Logo_Open_Hardware_SmallSymbol:OSHW-Symbol_6.7x6mm_SilkScreenLOGO1
1SMC24CANBPackage_TO_SOT_SMD:SOT-23D2
1SN65HVD230Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU6
1STM32F042C6TxPackage_QFP:LQFP-48_7x7mm_P0.5mmU1
1TestPoint_2PoleJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmTP1
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U3
1USB_Micro-B_Molex-105017-0001Connector_USB:USB_Micro-B_Molex-105017-0001J12
1XC6206P332MRPackage_TO_SOT_SMD:SOT-23U2

More from bondus/KlipperToolboard

6
  • 4 layers42 × 42 mmHuvud, the printed circuit board in 3D

    Huvud

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    126 parts373GPL-3.0
  • 4 layers42 × 42 mmHuvud, the printed circuit board in 3D

    Huvud

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    115 parts373GPL-3.0
  • 4 layers45 × 48 mmHuvud, the printed circuit board in 3D

    Huvud

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    91 parts373GPL-3.0
  • 2 layers65 × 56.5 mmCanHat, the printed circuit board in 3D

    CanHat

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    34 parts373GPL-3.0
  • 2 layers65 × 30 mmCanHat, the printed circuit board in 3D

    CanHat

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    33 parts373GPL-3.0
  • 2 layers83.8 × 20 mmCanCape, the printed circuit board in 3D

    CanCape

    bondus/KlipperToolboard

    A 3D printer tool head controller board

    21 parts373GPL-3.0

Similar boards

  • 2 layers98.2 × 35 mmFc660c, the printed circuit board in 3D

    Fc660c

    evyd13/fc660c-controller

    Custom FC660C controller with USB-C based on hasu's design

    30 parts22CC-BY-SA-4.0
  • 2 layers100 × 100 mmTouchtron, the printed circuit board in 3D

    Touchtron

    lynaghk/touchtron

    Rust touchpad / usb experiments

    120 parts21
  • 2 layers82.3 × 35.5 mmFc980c controller, the printed circuit board in 3D

    Fc980c controller

    wlhlm/fc980c-controller

    Leopold FC980C replacement keyboard controller

    38 parts20
  • 4 layers142.2 × 48 mmController, the printed circuit board in 3D

    Controller

    purdeaandrei/MiniRazz

    MiniRazz - open hardware controller replacement for the Unicomp Mini M keyboard

    74 parts14CERN-OHL-P-2.0
  • 2 layers45 × 45 mmAkaLinkPro, the printed circuit board in 3D

    AkaLinkPro

    akkako/akaLinkPro

    akaLinkPro 是一个基于 HPM5300 的高性能 CMSIS-DAP 调试器。

    95 parts11Apache-2.0
  • 4 layers55.8 × 20 mmWmbus, the printed circuit board in 3D

    Wmbus

    nobodyguy/wmbus_hardware

    WM-bus to USB

    27 parts7MIT
  • 2 layers353.1 × 124.9 mmSkeleton68rev2, the printed circuit board in 3D

    Skeleton68rev2

    skeletonkbd/Frost68

    252 parts5

Questions

How big is the CanTactDist PCB?

It measures 37 × 15 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CanTactDist use?

41 parts, built around the SN65HVD230D, USBLC6-2SC6 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CanTactDist KiCad files?

From the bondus/KlipperToolboard repository on GitHub, at the commit this page was made from: the board is PCB/HuvudCanUSB/CanTactDist.kicad_pcb and its schematic PCB/HuvudTiny2/Huvud.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CanTactDist design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).