

SPROJ3G2 Receiver PCB
SPROJ3G2 PRX PCB - KiCad files
- Size
- 65.1 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 66
- Pads
- 209
- Tracks, vias
- 627, 229
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 9 Dec 2024
- Updated
- 20 Dec 2024
Overview
SPROJ3G2 Receiver PCB is an open-source printed circuit board by boenike, from the boenike/SPROJ3G2_PRX_PCB repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 65.1 × 60 mm with 59 parts on 66 nets, routed with 627 tracks and 229 vias.
It is built around the RP2040, W25Q128JVSIQ and AMS1117-3.3, with the ABM8-272-T3, RR511D1121 and ZXMN3A03E6TA among its other parts. Its parts include 17 capacitors, 10 resistors, 7 connectors, 3 ICs and 3 switches. It belongs with the RP2040 boards of this library.
Main components
6RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystalsRR511D1121
-Rocker SwitchesE-SwitchZXMN3A03E6TA
SOT-26-55℃~+150℃ 1 N-channel 1.7W 104pF 12.6nC@10V 1V 30V 4.6A 50mΩ@10V 58.5pF 600pF N-Channel ±20V SOT-26 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
README.mdSPROJ3G2_PRX_PCB
SPROJ3EEG2 PRX PCB - KiCad files
Author: Bence Tóth
Course: BEng in Electronics
Campus: SDU Sonderborg
Semester: 3rd
Finish date: 2024/12/23
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C6, C7, C10, C11, C12, C13, C14, C15, C17 |
| 4 | 5K1 | Resistor_SMD:R_0805_2012Metric | R7, R8, R9, R10 |
| 2 | 15p | Capacitor_SMD:C_0805_2012Metric | C4, C5 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 1u | Capacitor_SMD:C_0805_2012Metric | C8, C9 |
| 2 | 27 | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 431183015816 | Switch_431183015816:431183015816 | S1, S2 |
| 2 | GNDTP | TestPoint:TestPoint_Pad_D1.0mm | TP3, TP6 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C16 |
| 1 | 2137160001 | USB_C_Port_213716-0001:2137160001 | J1 |
| 1 | 3V3_Supply_Voltage_Con | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J6 |
| 1 | 7VTP | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | 7V_Supply_Voltage_Con | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J5 |
| 1 | ABM8-272-T3 | Crystal_12MHz:ABM8-272-T3_ABR | X1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | DNP | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | GP12TP | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | GP13TP | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | GP14TP | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | GP15TP | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | LOGO | Logos:JLCPCB_Logo | G*** |
| 1 | LOGO | Logos:Raspberry_Pi_Logo | G*** |
| 1 | LOGO | Logos:SDU_Logo | G*** |
| 1 | RF24_Con | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J7 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | RR511D1121 | Switch_RR511D1121:RR511D1121 | S3 |
| 1 | SERVOTP | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | SJ_1 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | SJ_3 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | SJ_5 | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP5 |
| 1 | SWCLKTP | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | SWDIO_Con | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J3 |
| 1 | SWDTP | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | Servo_Con | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J4 |
| 1 | UART_Con | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J2 |
| 1 | W25Q128JVSIQ | SPI_Flash_W25Q128JVSIQ:W25Q128JVSIQ | U2 |
| 1 | ZXMN3A03E6TA | NMOS_ZXMN3A03E6TA:ZXMN3A03E6TA | Q1 |
The 58 most common of 59 parts.
Similar boards
- 2 layers100 × 60 mm

- 2 layers

- 2 layers182.4 × 128.8 mm

DYNAMO PCB
MekhyW/DYNAMO-PCB
(DEPRECATED) Power distribution and charging auxiliary PCB for the Dynamo project, designed using KiCAD
34 parts - 2 layers110 × 52 mm

- 2 layers62 × 47 mm

- 4 layers279.5 × 97 mm

Alpha centauri pcb
jacob-w-gable/alpha_centauri
A split, ergonomic, mechanical keyboard with 40 keys, designed for typing speed and comfort.
224 parts1MIT - 4 layers51.1 × 40.7 mm

- 4 layers91 × 91 mm

Questions
How big is the SPROJ3G2 Receiver PCB PCB?
It measures 65.1 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SPROJ3G2 Receiver PCB use?
59 parts, built around the RP2040, W25Q128JVSIQ, AMS1117-3.3 and ABM8-272-T3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SPROJ3G2 Receiver PCB KiCad files?
From the boenike/SPROJ3G2_PRX_PCB repository on GitHub, at the commit this page was made from: the board is SPROJ3G2_Receiver_PCB.kicad_pcb and its schematic SPROJ3G2_Receiver_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SPROJ3G2 Receiver PCB design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).