Skip to the content
2 layersBelice dot projector, the printed circuit board in 3D

Belice dot projector

bitmorse/specklesensor1

A photodiode array for laser speckle sensing and vibrometry.

Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
11
Pads
35
Tracks, vias
65, 31
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
9 Jan 2025
Updated
10 Jan 2025

Overview

Belice dot projector is an open-source printed circuit board by bitmorse, from the bitmorse/specklesensor repository on GitHub, published under the MIT licence. It is a 2-layer board with 12 parts on 11 nets, routed with 65 tracks and 31 vias.

It is built around the LT1800CS8#PBF and FMMT619TA. Its parts include 4 resistors, 2 capacitors, 2 connectors, 1 IC and 1 transistor.

Main components

2

README

README.md

specklesensor

A photodiode array for laser speckle sensing and vibrometry.

Read the full paper here.

PCB Design

Spectral analysis of a 133 Hz surface vibration under different laser configurations. Top: Power spectral density showing the target frequency component. Bottom: SNR improvement with increasing number of active lasers:

Multilaser Spectrogram

RPI Camera Bench Setup

RPI Camera Bench Setup

Side by side comparison of the speckle pattern captured by a Raspberry Pi camera with one red laser

1 Red Laser

and three red lasers.

3 Red Lasers

Laser setups

Different Laser Setups produce different speckles

Hardware

The PCBs used for the experiments are in the hardware folder. The PCBs are designed using KiCad, an open source schematics and layout editor. The PCBs were manufactured by JLCPCB and hand assembled using hot air reflow.

  • speckle_pcb_rev1: The 3x3 photodiode array.
  • speckle_amp_pcb_rev1: The amplifier PCB for 3x3 array.

Careful attention must be paid to cleaning the PCBs after soldering, as any residue flux can lead to leakage currents and noise in the measurements.

Scripts

  • emulations: The script to process camera frames to CSV files for emulating the photodiode array. A notebook provides the signal processing.
  • waveshare: Scripts for testing the first ADC.
  • daqhat: Scripts for testing the second ADC and data from the multi-laser experiment.

Parts

12
QtyValueFootprintReferences
2MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_PadH1, H2
110Resistor_SMD:R_0603_1608MetricR2
1100kResistor_SMD:R_0603_1608MetricR1
1100nCapacitor_SMD:C_0603_1608MetricC2
12 / 1.5WResistor_SMD:R_2512_6332MetricR4
1330Resistor_SMD:R_0603_1608MetricR5
139pCapacitor_SMD:C_0603_1608MetricC3
1Conn_01x02_Pinlib_fp:APDE-00J2
1Conn_01x04_PinConnector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_VerticalJ1
1FMMT619TAlib_fp:SOT95P237X112-3NQ1
1LT1800CS8lib_fp:SOIC127P599X175-8NIC1

More from bitmorse/specklesensor

3
  • 2 layers70 × 35 mmSpeckle amp pcb rev2, the printed circuit board in 3D

    Speckle amp pcb rev2

    bitmorse/specklesensor

    A photodiode array for laser speckle sensing and vibrometry.

    55 parts1MIT
  • 2 layers12.5 × 12.5 mmSpeckle pcb rev1, the printed circuit board in 3D

    Speckle pcb rev1

    bitmorse/specklesensor

    A photodiode array for laser speckle sensing and vibrometry.

    11 parts1MIT
  • 2 layersDot projector, the printed circuit board in 3D

    Dot projector

    bitmorse/specklesensor

    A photodiode array for laser speckle sensing and vibrometry.

    7 parts1MIT

Similar boards

  • 2 layers35 × 55 mmCoral ir, the printed circuit board in 3D

    Coral ir

    mineiwik/coral-ir

    Smart infrared transmitter

    31 partsMIT
  • 2 layers95.8 × 17.8 mmBivalveBit, the printed circuit board in 3D

    BivalveBit

    millerlp/BivalveBit_hardware

    Heart rate and valve gape sensor wearable for oysters and mussels

    55 partsGPL-3.0
  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915

Questions

What parts does the Belice dot projector use?

12 parts, built around the LT1800CS8#PBF and FMMT619TA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Belice dot projector KiCad files?

From the bitmorse/specklesensor repository on GitHub, at the commit this page was made from: the board is hardware/belice_dot_projector/belice_dot_projector.kicad_pcb and its schematic hardware/belice_dot_projector/belice_dot_projector.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Belice dot projector design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).