Skip to the content
2 layers69.1 × 53.8 mmKeezer, the printed circuit board in 3D

Arduino hat for Henry's kegerator

Size
69.1 × 53.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
59
Nets
62
Pads
209
Tracks, vias
383, 13
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171125)
Created
1 Jan 2018
Updated
5 Jan 2018

Overview

Keezer is an open-source printed circuit board by bistromath, from the bistromath/keezerhat repository on GitHub. It is a 2-layer board of 69.1 × 53.8 mm with 59 parts on 62 nets, routed with 383 tracks and 13 vias.

It is built around the INA828ID, ARDUINO UNO R3 and FOD817D3SD, with the LDK320M18R, B220 and BCP51 among its other parts. Its parts include 20 capacitors, 15 connectors, 14 resistors, 6 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

6

Parts

59
QtyValueFootprintReferences
100.1uFCapacitors_SMD:C_0805_HandSolderingC1, C2, C3, C4, C5, C7, C9, C11, C18, C19
81uFCapacitors_SMD:C_0805_HandSolderingC6, C8, C10, C12, C13, C14, C15, C16
410kResistors_SMD:R_0805_HandSolderingR6, R8, R10, R12
475.0Resistors_SMD:R_0805_HandSolderingR5, R7, R9, R11
4INA828Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mmU2, U3, U4, U5
210uFCapacitors_SMD:C_0805_HandSolderingC17, C20
21kResistors_SMD:R_0805_HandSolderingR1, R4
2DNPResistors_SMD:R_0805_HandSolderingR13, R14
12.2kResistors_SMD:R_0805_HandSolderingR3
14.7kResistors_SMD:R_0805_HandSolderingR2
1Arduino_UNO_R3Modules:Arduino_UNO_R3A1
1B220Diodes_SMD:D_SMB_HandsolderingD1
1BCP51TO_SOT_Packages_SMD:SOT-223-3_TabPin2Q1
1Barrel_JackConnectors:Barrel_Jack_CUI_PJ-102AHJ1
1DisplayConnectors_Molex:Molex_NanoFit_2x04x2.50mm_StraightJ11
1FOD817D3SDHousings_SOIC:SO-4_4.4x3.6mm_Pitch2.54mmU1
1FanConnectors_Molex:Molex_NanoFit_1x02x2.50mm_StraightJ3
1LDK320M18RTO_SOT_Packages_SMD:SOT-23-5_HandSolderingU6
1LOGOkeezer:CRABBSG***
1Load 1Connectors_Molex:Molex_NanoFit_2x02x2.50mm_StraightJ6
1Load 2Connectors_Molex:Molex_NanoFit_2x02x2.50mm_StraightJ7
1Load 3Connectors_Molex:Molex_NanoFit_2x02x2.50mm_StraightJ8
1Load 4Connectors_Molex:Molex_NanoFit_2x02x2.50mm_StraightJ9
1ModeConnectors_Molex:Molex_NanoFit_1x02x2.50mm_StraightJ12
1REFPin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmJ10
1RelayConnectors_Molex:Molex_NanoFit_1x02x2.50mm_StraightJ2
1RockerConnectors_Molex:Molex_NanoFit_1x03x2.50mm_StraightJ14
1TareConnectors_Molex:Molex_NanoFit_1x02x2.50mm_StraightJ13
1Temp 1Connectors_Molex:Molex_NanoFit_1x03x2.50mm_StraightJ4
1Temp 2Connectors_Molex:Molex_NanoFit_1x03x2.50mm_StraightJ5
1Temp VCCPin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmJ15

Similar boards

  • 2 layers30 × 10.1 mmPWM Isolator, the printed circuit board in 3D

    PWM Isolator

    EmbeddedDesign/GotT-Translation-Circuit

    A Bluetooth voice modulator for Dalek speech

    6 parts2MIT
  • 4 layers130 × 115 mm4ch Strain Gauge Collector, the printed circuit board in 3D

    4ch Strain Gauge Collector

    EERNINUO/4ch-Strain-Gauge-Collector

    4通道应变信号同步采集模块

    308 partsGPL-3.0
  • 4 layers100 × 100 mmAmod m, the printed circuit board in 3D

    Amod m

    gallicchio/AMOD-and-RFMOD

    The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…

    207 parts
  • 6 layers160 × 100 mmCH Card, the printed circuit board in 3D

    CH Card

    scular-HCC/DualLaserPDHDriver

    Dual laster Pound-Dreaver-Hall driver setup. 1550 nm DFBs. Q=10^-5. Less than 20 GHz difference

    145 parts
  • 2 layers154.5 × 73 mmPromprog2, the printed circuit board in 3D

    Promprog2

    Lazarus-L-o-n-g/PromProg

    PromProg is a versatile PROM Programmer for three basic PROM chips - 74188, 74S287 and 74S571. Device is based on ATmega16 microcontroller, data for programming can be downloaded from master computer from your preferred…

    95 parts8
  • 2 layers65.5 × 76.5 mmHeizungsregler, the printed circuit board in 3D

    Heizungsregler

    christof1977/kicad-heizungsregler

    basierend auf Raspberry Pi Zero - 10BaseT Ethernet (ENC28J60) - Schmalspur PoE: 24V Eingang über die äusseren Päärchen - Step-Down-Converter auf 5V - MBus-Interface zum Auslesen von Wärmemengenzähler - Anschluss für…

    119 parts
  • 2 layers165 × 135 mmCountdown timer, the printed circuit board in 3D

    Countdown timer

    MartinCowen/countdown-timer-hardware

    Child-friendly Countdown Timer: KiCad projects for PCB and Front Panel

    111 partsMIT
  • 2 layers76 × 37 mmPoweramp, the printed circuit board in 3D

    Poweramp

    M4a1x/nmr-spectrometer

    My master thesis at D-CHAB (ETH Zürich) - Building a 25MHz NMR spectrometer

    54 parts11GPL-3.0

Questions

How big is the Keezer PCB?

It measures 69.1 × 53.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Keezer use?

59 parts, built around the INA828ID, ARDUINO UNO R3, FOD817D3SD and LDK320M18R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Keezer KiCad files?

From the bistromath/keezerhat repository on GitHub, at the commit this page was made from: the board is keezer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Keezer design in my own project?

Its repository states no licence, so its author keeps all rights: ask bistromath before reusing the design.