

NOGPROG
PCB designs for Underwater Robotics at Berkeley (UR@B)
- Size
- 33 × 13 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 55
- Pads
- 149
- Tracks, vias
- 192, 44
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 1 Nov 2020
- Updated
- 12 Sep 2024
Overview
NOGPROG is an open-source printed circuit board by berkeleyauv, from the berkeleyauv/RoboSub_HW repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 33 × 13 mm with 34 parts on 55 nets, routed with 192 tracks and 44 vias.
It is built around the MIC5365-3.3YC5-TR and PRTR5V0U2X. Its parts include 13 resistors, 10 capacitors, 3 connectors, 2 ICs and 2 diodes. It belongs with the STM32 boards of this library.
Main components
2MIC5365-3.3YC5-TR
SC-70-5-40℃~+125℃ 1 150mA 200uVrms 3.3V 310mV@(150mA) 39uA 5.5V 65dB@(10kHz)、80dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SC-70-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
README
MATE/BackplaneTest/README.mdBackplaneTest
Tests the ESCC and PCC along with a Molex Super Sabre for power.
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 22 | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R8, R9, R10, R11 |
| 5 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C6, C7, C8, C9 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C2, C3, C10 |
| 2 | 100 | Resistor_SMD:R_0603_1608Metric | R7, R13 |
| 2 | 20p | Capacitor_SMD:C_0603_1608Metric | C4, C5 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 8MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | IF_BOOT | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | IF_SWD | Connector:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_Vertical | J2 |
| 1 | MIC5365-3.3YC5 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U1 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D1 |
| 1 | STM32F103CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | TGT_SWD | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J3 |
| 1 | USB_B_Micro | extraparts:USB_Micro-B_U254-05 | J1 |
| 1 | logo | extraparts:auv_logo | H1 |
| 1 | status | LED_SMD:LED_0603_1608Metric | D2 |
More from berkeleyauv/RoboSub_HW
9- 4 layers31.3 × 34 mm

- 2 layers115.6 × 104.1 mm

Power distribution board
berkeleyauv/RoboSub_HW
PCB designs for Underwater Robotics at Berkeley (UR@B)
41 parts3GPL-3.0 - 2 layers36 × 40 mm

- 2 layers

Noggin f072cb
berkeleyauv/RoboSub_HW
PCB designs for Underwater Robotics at Berkeley (UR@B)
26 parts3GPL-3.0 - 2 layers24 × 49 mm

- 2 layers19.5 × 30.8 mm

- 2 layers

Noggin g0b1ke
berkeleyauv/RoboSub_HW
PCB designs for Underwater Robotics at Berkeley (UR@B)
21 parts3GPL-3.0 - 2 layers36 × 18 mm

- 2 layers83.5 × 22 mm

BackplaneTest
berkeleyauv/RoboSub_HW
PCB designs for Underwater Robotics at Berkeley (UR@B)
8 parts3GPL-3.0
Similar boards
- 4 layers45 × 63.5 mm

- 2 layers70.3 × 38 mm

JABICAN USB Pro
dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere
92 parts14Apache-2.0 - 4 layers24.4 × 24.4 mm

OSO SWAT C1
joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch
40 parts2.1k - 2 layers335 × 340.9 mm

RCA Radio Telescope
Glaubinator/Radio-Telescope-RCA
Radio Telescope System for 1 GHz to 2 GHz Operation
81 parts3GPL-3.0 - 4 layers80 × 100 mm

Ice40 breakout
RubenVoell/iceduino
The basic idea behind this project is to create a simple breakout of an ICE40 FPGA with some LEDs and Buttons to interact with the FPGA and enough resources to run a simple softcore, like a small RISC-V core.
248 parts3 - 4 layers70 × 30 mm

Usb led controller
kcuzner/usb-led-controller
This is an LED controller for the lights that came with my In-Win A1 Mini-ITX Tower. It came with a simple 12V RGB LED strip, rather than the now-standard WS2812 addressable LED strips that are so common in today's PCs.
115 parts2 - 4 layers115 × 75 mm

- 2 layers81 × 127 mm

RPNCalcProject
aydenschmidtnd/RPNCalcProject
Due to the cost of reverse polish notation (RPN) calculators, I wanted to make the attempt at creating one myself.
103 parts1
Questions
How big is the NOGPROG PCB?
It measures 33 × 13 mm and has 2 copper layers, 1.6 mm thick.
What parts does the NOGPROG use?
34 parts, built around the MIC5365-3.3YC5-TR and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the NOGPROG KiCad files?
From the berkeleyauv/RoboSub_HW repository on GitHub, at the commit this page was made from: the board is General/NOGPROG/NOGPROG.kicad_pcb and its schematic General/ESCB/ESCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the NOGPROG design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).