2 layers18.5 × 110 mm
Exits board A
ramphands/Exits
4hp DIY eurorack line and headphone output module based on the Nearness and AJH headphone amp modules
42 parts33
2 layers99.1 × 47.7 mm
Exits-1U
benregnier/Exits-1U44hp DIY eurorack line and headphone output module based on the "Exits" module by Ramphands, 1U format with IJ outs
- Size
- 99.1 × 47.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 42
- Pads
- 215
- Tracks, vias
- 332, 41
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 17 May 2025
- Updated
- 24 May 2025
Overview
Exits-1U is an open-source printed circuit board by benregnier, from the benregnier/Exits-1U repository on GitHub. It is a 2-layer board of 99.1 × 47.7 mm with 70 parts on 42 nets, routed with 332 tracks and 41 vias.
It is built around the LME49720NA, NE5532 and 1N5819HW, with the ADP0204 and SJ-63083A among its other parts. Its parts include 32 resistors, 16 connectors, 14 capacitors, 4 ICs and 2 diodes. It belongs with the audio and music boards of this library.
Main components
5
LME49720NA
PDIP-8-17V~-2.5V、2.5V~17V -40℃~+85℃ 0.00003% 10mA 120dB 2-Channel PDIP-8 Operational Amplifier ROHSTexas InstrumentsAudio Amplifiers
NE5532
SOP-8-22V~22V 0℃~+70℃ 100dB 10nA 14mA 2 40V/us 42mA 4mV 800nA 8nV/√Hz@30Hz Built-in compensation SOP-8 Operational Amplifier ROHSSungineOperational Amplifier
1N5819HW
SOD-123-65℃~+150℃ 1 Independent 1A 1mA@40V 25A 40V 450mV@1A SOD-123 Schottky Diodes ROHSDiodes IncorporatedSchottky DiodesADP0204
插件插件 DIP Switches ROHSTE ConnectivityDIP Switches
SJ-63083A
--25℃~+70℃ 12V 1A Brass、Phosphor Bronze Silver - Audio Connectors ROHSCUIAudio Connectors (Headphones)
README
README.mdExits
4hp DIY eurorack line and headphone output module based on Exits which is in part based on Nearness and Forestcaver headphone amp designs.
The Nearness section is a "minimal panning mixer for the Eurorack modular synthesizer system. Seven inputs, two outputs. The closer an input is to an output, the greater its influence on it."
This design makes the following changes:
- Changed to a 1U format
- Reestablishes front panel L and R outputs
- In lieu of a stereo 1/4 main out, has a six-pin connector that is compatible with Intellijel cases.
- NE5532 in lieu of NJM4556 for the headphone portion
Schematic and PCBs
The kicad directory contains the schematic and PCB layout as a KiCad 6 project.
Panel
Available in the panel directory as a PDF and an SVG vector file as well as PCB design and gerbers.
Intellijel Output Pinout
This module has a six pin connector on the back meant to be compatible with outputs on Intellijel and Befaco cases. Pinouts match per the diagram below. Outputs are not balanced. Note that if you want to mount this module on the far right hand side of the case both the output and power ribbon cables need to be low-profile.
License
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R14, R15, R16, R17, R18, R19, R20, R21, R22, R27, R28 |
| 10 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C7, C8, C9, C10, C11, C12, C13, C14 |
| 9 | PJ301M12 | nearness:PJ301M12 | J1, J2, J3, J4, J5, J6, J7, J13, J15 |
| 4 | 1 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R24, R25, R26 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R29, R30, R31, R32 |
| 2 | 102k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R12 |
| 2 | 113k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R10 |
| 2 | 140k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R8 |
| 2 | 1M69 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R13 |
| 2 | 1N5819HW | Diode_SMD:D_SOD-123 | D1, D2 |
| 2 | 215k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R9 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4 |
| 2 | 22u | Capacitor_SMD:C_Elec_5x5.8 | C5, C6 |
| 2 | 442k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R11 |
| 2 | LME49720 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3, U4 |
| 2 | NE5532 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | IC1, IC2 |
| 1 | 50k A | Potentiometer_THT:Potentiometer_Alpha_RD902F-40-00D_Dual_Vertical | RV1 |
| 1 | ADP0204 | Library:ADP0204 | S1 |
| 1 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J9 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | Conn_01x06_Female | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J10 |
| 1 | Conn_01x06_Male | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J16 |
| 1 | Euro power header | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J12 |
| 1 | SJ-63083A | Library:CUI_SJ-63083A | J14 |
Similar boards
- 2 layers38.3 × 110 mm
- 2 layers39.4 × 106.7 mm
Nearness
sarnesjo/nearness
Minimal panning mixer for the Eurorack modular synthesizer system
52 parts99 - 2 layers49.8 × 110 mm
Nearness
bmoren/attenuated-nearness
a 6hp variation of the nearness eurorack module which adds an attenuator to each input!
61 parts17 - 2 layers164.6 × 39.9 mm
- 2 layers164.5 × 106 mm
- 2 layers29.2 × 106.7 mm
- 2 layers134 × 109.5 mm
FreeDSP SMD AB plus
CyberPit/FreeDSP_Classic_SMD_AB_plus-II
An extended version of FreeDSP Classic SMD A/B
233 parts6
Questions
How big is the Exits-1U PCB?
It measures 99.1 × 47.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Exits-1U use?
70 parts, built around the LME49720NA, NE5532, 1N5819HW and ADP0204. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Exits-1U KiCad files?
From the benregnier/Exits-1U repository on GitHub, at the commit this page was made from: the board is Kicad/Exits-1U.kicad_pcb and its schematic Kicad/Exits-1U.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Exits-1U design in my own project?
Its repository states no licence, so its author keeps all rights: ask benregnier before reusing the design.