
Wireless measurement ard
benlhy/wireless_measurements
A simple, compact wireless tool to measure low power circuits

A simple, compact wireless tool to measure low power circuits
Wireless measurement ard is an open-source printed circuit board by benlhy, from the benlhy/wireless_measurements repository on GitHub. It is a 4-layer board of 30 × 23 mm with 29 parts on 62 nets, routed with 348 tracks and 34 vias.
It is built around the JDY-08, MAX40204ANA+ and MCP16415-I/UN. Its parts include 9 capacitors, 8 resistors, 6 ICs, 2 connectors and 1 diode. It belongs with the sensors and measurement and home automation and IoT boards and the Silicon Labs (EFR32, EFM) boards of this library.
The Simple Wireless Measurement (SWM) board is just that - it is a simple board designed to do wireless measurements for remote embedded circuits. It is capable of measuring current and voltage and transmitting it over Bluetooth.
You can retrieve the data with Python, NRF Connect App, or the Flutter app designed to display this data.
This Repo consists of the hardware and software required to run the board.
The SWM board uses an EFM8LB12 microcontroller from Silabs to do the analog measurements. The EFM8 is capable of 14-bit ADC measurements with multiple inputs.
The SWM board uses the JDY-08 Bluetooth module because it provides a simple and transparent way to communicate readings over BLE: just connect and send the data over UART. It is also a very low-cost module (< $4).
It is powered by the MCP16415 boost module which can take input ranges from 0.8V to 5.5V, which means that it can be powered by anything from a single AA rechargable to a 5V input from another board.
The total cost of the board comes up to roughly $15, which makes it cheap enough to throw permanently into a system to do wireless reporting of voltage and current. The board size is also small - about the size of two postage stamps placed side by side, which allows it to be embedded in other applications.
| Use case | Description |
|---|---|
| Drones | Measure the power draw of electronics on your drone over time |
| Robotics | Keep an eye on motors and batteries |
| IoT | Monitor battries remotely |
| Distributed systems | Monitor various test points in the system simultaneously to get a holistic picture of what is going on |
| Rocketry | Monitor your wireless systems as you mount the rocket. Never wonder again if your system is dead. |
| Current draw | Voltage | Status |
|---|---|---|
| 48 mA | 1.2V | Fully On |
| 15 mA | 3.3V | Fully On |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C4 |
| 2 | 110k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C3 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8 |
| 2 | MAX40204 | ben_common:BGA-8_4x2_1.468x0.848mm | U4, U5 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C6 |
| 1 | 1R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 1 | 1R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 360k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5 |
| 1 | 4.7uH | Inductor_SMD:L_Bourns-SRN4018 | L1 |
| 1 | 866k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | Battery1 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Horizontal | J1 |
| 1 | EFM8LB1 | Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm | U1 |
| 1 | JDY-08 | JDY-08:JDY-08_HandSoldering | U2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | Logo | icons:icon | U6 |
| 1 | MCP16415 | Package_SO:MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | SW_SPDT | ben_common:SW_SPDT_CK-JS102011SAQN | SW1 |
| 1 | Tag-Connect | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J2 |

benlhy/wireless_measurements
A simple, compact wireless tool to measure low power circuits

deebot/MorphWatch-STM32
The Repo contains KiCAD hardware files and software for Morph Watch


Hanqaqa/Easyduino
Easily dive into different PCB KiCad designs of the most popular microcontroller devboards


EvanKrall/pipad
A PCB for putting a Raspberry Pi CM4 inside a 1st-generation iPad.


alvarop/chaac
This is a work in progress for a wireless weather station project.

It measures 30 × 23 mm and has 4 copper layers, 1.6 mm thick.
29 parts, built around the JDY-08, MAX40204ANA+ and MCP16415-I/UN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the benlhy/wireless_measurements repository on GitHub, at the commit this page was made from: the board is mini/hardware/wireless_measurement_ard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask benlhy before reusing the design.