BellssGit/IMX662_module_for_raspberry_pi12A simple camera module for Raspberry Pi using IMX662 sensor
Raspberry pi IMX662 is an open-source printed circuit board by BellssGit, from the BellssGit/IMX662_module_for_raspberry_pi repository on GitHub, published under the GPL-2.0 licence. It is a 4-layer board of 40 × 40 mm with 48 parts on 44 nets, routed with 297 tracks and 64 vias.
It is built around the IMX662-AAQR-C, SPX3819M5-L-1-2/TR and SPX3819M5-L-1-8, with the TXS0104EPWR-TP among its other parts. Its parts include 30 capacitors, 6 resistors, 4 ICs, 1 diode and 1 connector.
A simple camera module for Raspberry Pi using IMX662 sensor
too lazy to adjust the focus, sorry.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 10uF | Library:C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C7, C9, C15, C18, C22, C23, C30 |
| 9 | 100nF | Library:C_0402_1005Metric | C10, C12, C14, C17, C19, C20, C21, C27, C29 |
| 7 | 1uF | Library:C_0402_1005Metric | C8, C11, C13, C16, C24, C25, C28 |
| 4 | 1K | Library:R_0402_1005Metric | R1, R2, R3, R6 |
| 2 | MountingHole_Pad | Library:MountingHole_2.2mm_M2_Pad | H1, H2 |
| 2 | MountingHole_Pad | Library:MountingHole_3.2mm_M3_Pad | H5, H6 |
| 1 | 0R | Library:R_0402_1005Metric | R5 |
| 1 | 10K | Library:R_0402_1005Metric | R4 |
| 1 | C | Library:C_0603_1608Metric | C26 |
| 1 | Conn_01x15_MountingPin | Library:TE_1-84953-5_1x15-1MP_P1.0mm_Horizontal | J2 |
| 1 | FerriteBead | Library:L_0805_2012Metric | FB1 |
| 1 | IMX662AAQR | Library:LGA-114_11x14_9.3x12.0mm | U1 |
| 1 | LED | Library:LED_0603_1608Metric | D1 |
| 1 | SG-210SDD | Library:Oscillator_SMD_Abracon_ASE-4Pin_3.2x2.5mm | X1 |
| 1 | SPX3819M5-L-1-2 | Library:SOT-23-5 | U2 |
| 1 | SPX3819M5-L-1-8 | Library:SOT-23-5 | U4 |
| 1 | TXS0104EPWR | Library:TSSOP-14_4.4x5mm_P0.65mm | U3 |
osqzss/PocketSDR
The Pocket SDR FE device includes 2, 4, or 8 RF frontend channels, supporting the GNSS L1 band (1525 - 1610 MHz) or L2/L5/L6 bands (1160 - 1290 MHz). For these signal bands, refer to GNSS Signal Bands.
eutectic6337/TNbadge
Data point: after soldering only the front components (5x smart LED, 2x resistor) on 5 boards, I had 1 board with no erroneous beeps in the continuity test.
Case-Rocket-Team/PayloadPrototypeBoard2021
Prototype Payload Board for the 2021 ESRA Payload using Parafoil Guidance. KiCad Project
pebender/wireless_adapter_for_mitsubishi
This project is neither associated with nor endorsed by Mitsubishi Electric. By using this project, you may void your warranty or break your heat pump.
It measures 40 × 40 mm and has 4 copper layers, 1.6 mm thick.
48 parts, built around the IMX662-AAQR-C, SPX3819M5-L-1-2/TR, SPX3819M5-L-1-8 and TXS0104EPWR-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the BellssGit/IMX662_module_for_raspberry_pi repository on GitHub, at the commit this page was made from: the board is Hardware/Raspberry_pi_IMX662.kicad_pcb and its schematic Hardware/Raspberry_pi_IMX662.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).