

- Size
- 36 × 48.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 47
- Pads
- 156
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Mar 2023
- Updated
- 20 May 2026
Overview
SAS is an open-source printed circuit board by bask185, from the bask185/Train-Science-DIY repository on GitHub. It is a 2-layer board of 36 × 48.5 mm with 40 parts on 47 nets.
It is built around the ATMEGA328PB-MU, LM2596S-5.0 and BC847. Its parts include 11 connectors, 10 resistors, 7 capacitors, 4 transistors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATMEGA328PB-MU
QFN-32-EP(5x5)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R8, R9 |
| 4 | BC847 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | C | Capacitor_SMD:C_0805_2012Metric | C1, C3, C6, C7 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R6, R7, R10 |
| 2 | 22nF | Capacitor_SMD:C_0805_2012Metric | C2, C4 |
| 2 | servo | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7, J8 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 10K | Potentiometer_THT:Potentiometer_Runtron_RM-065_Vertical | RV1 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | ATmega328PB-MU | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U1 |
| 1 | Crystal | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y1 |
| 1 | D | Diode_SMD:D_2010_5025Metric | D1 |
| 1 | D_Schottky | Diode_SMD:D_2010_5025Metric | D2 |
| 1 | HEADER_3x2 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J11 |
| 1 | L | Inductor_SMD:L_6.3x6.3_H3 | L1 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U2 |
| 1 | SW_DIP_x04 | Button_Switch_THT:SW_DIP_SPSTx04_Piano_10.8x11.72mm_W7.62mm_P2.54mm | SW1 |
| 1 | buttons | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J3 |
| 1 | config | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J4 |
| 1 | controlSignals | TerminalBlock:TerminalBlock_bornier-3_P5.08mm | J2 |
| 1 | detector | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J5 |
| 1 | jumper | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | power | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J9 |
| 1 | relay | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Horizontal | J6 |
| 1 | signalLights | TerminalBlock:TerminalBlock_bornier-5_P5.08mm | J1 |
More from bask185/Train-Science-DIY
12- 2 layers75 × 106.5 mm

- 2 layers68.5 × 130.5 mm

- 2 layers153.2 × 127.5 mm

- 2 layers54.5 × 73 mm

- 2 layers99.5 × 61 mm

- 4 layers70 × 83.5 mm

- 2 layers105.5 × 63.5 mm

- 2 layers78 × 58.5 mm

- 2 layers83.5 × 50.3 mm

- 2 layers81 × 71.2 mm

- 2 layers54 × 94.5 mm

- 2 layers100 × 45 mm

Similar boards
- 6 layers80 × 49 mm

ButterStick
butterstick-fpga/butterstick-hardware
Basic ECP5 based GigE to SYZYGY interface.
256 parts225 - 4 layers115 × 85.8 mm

- 4 layers50 × 50 mm

- 6 layers42.6 × 42.6 mm

Project OAK MAIN BRD V0
0101shift/Project_OAK
All design files, source code, and documentation for Project OAK, a digital watch inspired by mechanical complications.
145 parts29MIT - 4 layers115 × 65 mm

- 2 layers39 × 39.4 mm

Stepper Controller
Case-Rocket-Team/StepperMotorControllerBoard
ATMEL Stepper Motor Controller Board prototype for the Cobra Air Brakes test rocket
44 parts1 - 2 layers13.3 × 13.3 mm

- 2 layers85 × 56 mm

Questions
How big is the SAS PCB?
It measures 36 × 48.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SAS use?
40 parts, built around the ATMEGA328PB-MU, LM2596S-5.0 and BC847. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SAS KiCad files?
From the bask185/Train-Science-DIY repository on GitHub, at the commit this page was made from: the board is PCB_SOURCE/blockModules/SAS/SAS_SMD/SAS.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the SAS design in my own project?
Its repository states no licence, so its author keeps all rights: ask bask185 before reusing the design.