
Dc motor driver adapter
baden/dc-motor-driver-adapter
Плата для підключення польотного контролера до драйвера DC-двигуна. PPM в аналог 5..0В.

Плата для підключення польотного контролера до драйвера DC-двигуна. PPM в аналог 5..0В.
Dc motor driver adapter is an open-source printed circuit board by baden, from the baden/dc-motor-driver-adapter repository on GitHub. It is a 2-layer board of 36.2 × 30.4 mm with 33 parts on 55 nets, routed with 34 tracks and 3 vias.
It is built around the L7805, USBLC6-2P6 and USBLC6-2SC6, with the USBLC6-4SC6 and BC817 among its other parts. Its parts include 7 capacitors, 7 resistors, 6 ICs, 6 connectors and 4 transistors. It belongs with the robots and motor control and interfaces and adapters boards and the RISC-V boards of this library.
Тут буде і плата і програма.
https://github.com/riscv-software-src/homebrew-riscv
brew tap riscv-software-src/riscv
brew install riscv-tools
brew install riscv-openocd
brew test riscv-tools
/opt/homebrew/opt/riscv-gnu-toolchain/bin/riscv64-unknown-elf-gcc --version/opt/homebrew/opt/riscv-openocd/bin/openocd
Во, подивиться це:
https://github.com/wagiminator/CH32V003-GameConsole/tree/main
Ще це: https://github.com/wagiminator/MCU-Templates
Ще тут купа посилань: https://github.com/wagiminator/Development-Boards/tree/main/CH32V003A4M6_DevBoard
https://github.com/AlessandroAU/ESP32-CRSF-Packet-Gen/blob/master/CRSF_testcode/CRSF.h https://px4.github.io/Firmware-Doxygen/d9/dd2/crsf_8cpp_source.html
https://vedder.se/2015/10/communicating-with-the-vesc-using-uart/
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 4.7k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7 |
| 5 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C5, C6, C7 |
| 5 | Conn_01x03_Pin | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J2, J4, J5, J6, J7 |
| 4 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2 |
| 1 | CH32V003AxMx | Package_SO:SOP-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | Conn_01x03 | Connector_JST:JST_PH_S5B-PH-K_1x05_P2.00mm_Horizontal | J1 |
| 1 | L7805 | Package_TO_SOT_SMD:TO-252-2 | U6 |
| 1 | MCP6002-xSN | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | USBLC6-4SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |

baden/dc-motor-driver-adapter
Плата для підключення польотного контролера до драйвера DC-двигуна. PPM в аналог 5..0В.

baden/dc-motor-driver-adapter
Плата для підключення польотного контролера до драйвера DC-двигуна. PPM в аналог 5..0В.

Twisted-Fields/rp2040-motor-controller
A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.

apfaudio/sandflat
Lower-cost DSP experimentation host for the SoldierCrab ECP5 SoM

huming2207/picouart
CH340X based UART dongle for ESP32/STM32 UART Bootloader firmware downloading

wonzaj/Amplituner
Audio amplituner with display, bass, middle, treble control. It has:

Twisted-Fields/acorn-robot-electronics
PCB hardware designs in KICAD for Acorn, the precision farming rover from Twisted Fields.

leptun/Avionus_Flight_Controller
Controller board for autonomous RC plane


enkhbold470/kicad-projects
Five KiCad 10 boards (4- and 6-layer): ESP32-S3 industrial gateway, USB-C PD bench supply, RP2040 logic analyzer, FOC motor controller, iCE40 FPGA board.
It measures 36.2 × 30.4 mm and has 2 copper layers, 1.6 mm thick.
33 parts, built around the L7805, USBLC6-2P6, USBLC6-2SC6 and USBLC6-4SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the baden/dc-motor-driver-adapter repository on GitHub, at the commit this page was made from: the board is board/revision-3/dc-motor-driver-adapter.kicad_pcb and its schematic board/revision-1/dc-motor-driver-adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask baden before reusing the design.