

Pd sniffer
- Size
- 63.8 × 44 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 44
- Nets
- 88
- Pads
- 224
- Tracks, vias
- 366, 81
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 22 May 2026
- Updated
- 22 May 2026
Overview
Pd sniffer is an open-source printed circuit board by Badbird5907, from the Badbird5907/pd-sniffer repository on GitHub. It is a 2-layer board of 63.8 × 44 mm with 44 parts on 88 nets, routed with 366 tracks and 81 vias.
It is built around the STM32G0B1RET6, INA229AIDGSR and AP2112K-3.3, with the PRTR5V0U2X, AO4407A and BZX84C12 among its other parts. Its parts include 14 capacitors, 9 resistors, 4 ICs, 4 diodes and 3 connectors. It belongs with the STM32 boards of this library.
Main components
9STM32G0B1RET6
LQFP-64(10x10)-40℃~+85℃ 1.7V~3.6V 144KB 32 Bit 512KB 60 64MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)INA229AIDGSR
VSSOP-10-40℃~+125℃ 1 100pA 10nV/℃ 170dB 2.7V~5.5V 300nV 640uA 98V High-side detection、Low-side detection、Bidirectional detection、Zero drift / auto-zero、Power monitoring、Digital output interface、Programmable threshold alarm、Integrated ADC、Enable/shutdown function、Integrated shunt ±163.84mV VSSOP-10 Current Sense Amplifiers ROHSTexas InstrumentsCurrent Sense AmplifiersAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)AO4407A
SOP-8-55℃~+150℃ 1 P-Channel 1.8V 14A 2.05nF 20nC@4.5V、40nC@10V 3.1W 300pF 30V 330pF 9.5mΩ@10V、14.7mΩ@4.5V SOP-8 MOSFETs ROHSUMWMOSFETsBZX84C12
SOT-23Zener DiodeshongjiachengCPN4020H100MT
SMD,4x4mmSMD,4x4mm Power Inductors ROHSMagnetsycPower InductorsMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)SMAJ20A
DO-214AC(SMA)ESD And Surge Protection (TVS/ESD)hongjiacheng
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C7, C8, C11, C13, C14 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R4, R6, R8 |
| 4 | MountingHole | MountingHole:MountingHole_2.5mm | H1, H2, H3, H4 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric | C5, C9, C10 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric | R7, R9 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C12, C15 |
| 2 | 47uF | Capacitor_SMD:C_1206_3216Metric | C2, C3 |
| 2 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D2, D4 |
| 2 | USB C | Components:USB-SMD_GT-USB-7010AN | J1, J2 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 5m Shunt | Resistor_SMD:R_2512_6332Metric | R1 |
| 1 | 75k | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | AO4407A | Components:SOIC127P600X175-8N | Q1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | BZX84C12 | Package_TO_SOT_SMD:SOT-23 | D3 |
| 1 | CPN4020H100MT | Components:IND-SMD_L4.0-W4.0_ASPI-4030S | L1 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | INA229AIDGSR | Package_SO:TSSOP-10_3x3mm_P0.5mm | U2 |
| 1 | LUTE 2920L500/24GR | Fuse:Fuse_2920_7451Metric | F1 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | SMAJ20A | Diode_SMD:D_SMA | D1 |
| 1 | ST7789_EYESPI | Components:FPC-SMD_18P-P0.50_FPC-05F-18PH20 | FPC1 |
| 1 | STM32G0B1RET6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TPS54302DDCR | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | ~ | Components:SW-SMD_4P-L5.2-W5.2-P3.70-LS6.4 | SW1 |
Similar boards
- 4 layers172.5 × 85 mm

- 2 layers78 × 60 mm

DC Motor Controller
minhle4397/Line-Follower-Robot-v2
Improved Hardware and Firmware for Line Follower Robot
53 parts3 - 4 layers123 × 75 mm

- 2 layers180 × 80 mm

- 2 layers101.2 × 86.5 mm

Windmeasureboard
GGoodacre/WindChargeController-Capstone2024
Solar Charge Controller for BEng Capstone 2024
28 parts1 - 2 layers65 × 56 mm

PiGarage
bryce-builds/PiGarage
Open-source Raspberry Pi power management and audio HAT for automotive head-unit use
79 parts9 - 2 layers62 × 6 mm

TableLight
jonny190/TableLight
A 3D-printable, battery-powered, USB-C rechargeable table lamp in the classic "Poldina" shape - honeycomb disc base, thin stem, down-firing cone shade with a white top - running WLED on an ESP32, with a capacitive touch…
72 partsMIT - 4 layers100 × 100 mm

Questions
How big is the Pd sniffer PCB?
It measures 63.8 × 44 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pd sniffer use?
44 parts, built around the STM32G0B1RET6, INA229AIDGSR, AP2112K-3.3 and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pd sniffer KiCad files?
From the Badbird5907/pd-sniffer repository on GitHub, at the commit this page was made from: the board is PCB/pd-sniffer.kicad_pcb and its schematic PCB/pd-sniffer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pd sniffer design in my own project?
Its repository states no licence, so its author keeps all rights: ask Badbird5907 before reusing the design.