Skip to the content
2 layers75.2 × 100.1 mmPanel, the printed circuit board in 3D

Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

Size
75.2 × 100.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
26
Nets
19
Pads
126
Tracks, vias
537, 0
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
1 Aug 2017
Updated
16 May 2023

Overview

Panel is an open-source printed circuit board by b00lduck, from the b00lduck/esp32-audioplayer repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 75.2 × 100.1 mm with 26 parts on 19 nets, routed with 537 tracks and 0 vias.

README

README.md

esp32-audioplayer

ESP32 based MP3 audio player with RFID control and case made from laser cutted plywood

!!! WORK IN PROGRESS !!! !!! not functional yet !!!

Used electronic hardware components:

  • ESP32 NodeMCU module
  • RFID-RC522 module (i.e. https://www.ebay.de/itm/172603664748)
  • VS1053B module with SD-slot (i.e. http://www.ebay.de/itm/272761135002)
  • Mifare classic 13.56MHz RFID cards (clones will do the job too, i.e. http://www.ebay.de/itm/122525501095)
  • Adafruit PowerBoost 500 Charger module
  • 3.7V LiPo battery
  • Class-D amplifier module
  • SD-Card (i.e. 4GB)
  • two Visaton FR7 (4 ohms) speakers
  • Custom main board (see kicad folder for layout)
  • Custom panel board (see kicad folder for layout)
  • 1x 220uF 35V
  • 1x 1uF 63V
  • 4x 100nF
  • 2x 47nF
  • 1x resistor ladder 4x 4.7k
  • 1x 10R
  • 1x 10kR
  • 1x 22kR
  • 4x WSL10 (2x5 header 2.54mm with notch)
  • 2x 2-pin header 2.54mm
  • 4x 4-pin header 2.54mm
  • some wire for airwires
  • some insulated wire 1mm², red and black (for internal connections)
  • 1x USB 2 Micro-B connector
  • 1x power switch
  • 1x USB 2 micro cable (for internal connection)
  • optional: MEMS gyroscope module
  • optional: 0.96 inch I2C OLED display

Wood parts:

  • 6 sheets, one for every side of the case
  • 2 distance rings for the speakers

Metal parts:

  • 2x 100x75x0.8mm aluminium sheet

3D-Printed parts:

  • 8x inner edge reinforcements
  • 4x M3x3 standoff
  • 8x M3*8 standoff (for main board)
  • 4x M3x11 standoff (for MP3 board)
  • 2x M3x6 standoff (for panel board)
  • 2x M3x4 standoff (for panel board)
  • 1x USB receptacle holder
  • 1x SD-Card slot box
  • 1x SD-Card slot cover

Screws

  • 4x M3x25 DIN 7991/ISO 10642 (countersunk allen bolt)
  • 32x M3 DIN 934/ISO 4042 (nut)
  • 8x M3 DIN 125/ISO 7089 (washer)
  • 8x M3x20 DIN 912/ISO 4762 (cylinder head allen bolt)
  • 2x M2x10 DIN 912/ISO 4762 (cylinder head allen bolt) for amp
  • 2x M2 DIN 934/ISO 4042 (nut)
  • 2x M2 DIN 125/ISO 7089 (washer)
  • 8x M3x?? DIN 7991/ISO 10642 (countersunk allen bolt) for speakers
  • 24x M3x15 DIN 7991/ISO 10642 (countersunk allen bolt) for inner corners

Used software:

  • VSCode with PlatformioIDE

Used Arduino Libraries:

  • SdFat 1.0.7
  • MFRC522 1.3.6

Port mapping

see src/config.h

3D printing

I used black 1.75 PETG filament for all parts. Layer height was 0.15mm at a printign speed of 30mm/s.

Parts

26
QtyValueFootprintReferences
3PanelConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ4, J4, J4
3RFIDConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ2, J2, J2
3RFIDConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ1, J1, J1
3btn1Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3, J3, J3
3btn2Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ5, J5, J5
3btn3Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ6, J6, J6

The 18 most common of 26 parts.

More from b00lduck/esp32-audioplayer

2
  • 2 layers100 × 75 mmAudioplayer, the printed circuit board in 3D

    Audioplayer

    b00lduck/esp32-audioplayer

    Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

    40 parts2GPL-3.0
  • 2 layers65.1 × 28.6 mmPower, the printed circuit board in 3D

    Power

    b00lduck/esp32-audioplayer

    Arduino IDE sketch for a ESP8266 based MP3 audio player with RFID control

    32 parts2GPL-3.0

Similar boards

  • 2 layers57.3 × 19 mm11ua, the printed circuit board in 3D

    11ua

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    26 parts990GPL-3.0
  • 2 layers98 × 59.5 mmMCP23017 PCB, the printed circuit board in 3D

    MCP23017 PCB

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    26 parts915
  • 2 layers142.9 × 98.5 mmCantor MX, the printed circuit board in 3D

    Cantor MX

    diepala/cantor

    Cantor keyboard, a 42 key diodeless split keyboard.

    26 parts756GPL-3.0
  • 2 layers103.8 × 50 mmGalagino pcb set, the printed circuit board in 3D

    Galagino pcb set

    harbaum/galagino

    A Galaga, Pac-Man and Donkey Kong arcade emulator for the ESP32

    26 parts558
  • 2 layers20.3 × 34.8 mmL0 ESP32, the printed circuit board in 3D

    L0 ESP32

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    26 parts546MIT
  • 2 layers40.6 × 50.8 mmWALTsm, the printed circuit board in 3D

    WALTsm

    google/walt

    A device for measuring latency of physical sensors and outputs on phones and computers

    26 parts474Apache-2.0
  • 2 layers158.5 × 75 mmDoj v2, the printed circuit board in 3D

    Doj v2

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    26 parts463

Questions

How big is the Panel PCB?

It measures 75.2 × 100.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Panel use?

26 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Panel KiCad files?

From the b00lduck/esp32-audioplayer repository on GitHub, at the commit this page was made from: the board is kicad/panel/panel/panel.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Panel design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).