2 layers42 × 67 mm
2 layers40 × 55 mm
Matrix
Az154za/SGT_SCREEN1To build your own, just grab the gerber files, and send them to your preferred PCBA fab # Features : - 1212 led matrix - 30 free GPIO by RP2040 - usbc input
- Size
- 40 × 55 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 190
- Nets
- 78
- Pads
- 538
- Tracks, vias
- 1,259, 101
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 Feb 2026
- Updated
- 3 May 2026
Overview
Matrix is an open-source printed circuit board by Az154za, from the Az154za/SGT_SCREEN repository on GitHub. It is a 2-layer board of 40 × 55 mm with 190 parts on 78 nets, routed with 1,259 tracks and 101 vias.
It is built around the RP2040 and W25Q128JVSIQ. Its parts include 144 diodes, 24 capacitors, 10 resistors, 6 connectors and 4 ICs. It belongs with the lEDs and displays boards and the RP2040 boards of this library.
Main components
2
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
README
README.mdSGT_SCREEN
Well this is a DEV BOARD that has 12*12 led screen ( matrix) driven by led DRIVER IS31FL3737 and controlled by RP2040 this design was the third version I made after a lot of modification ( part placements , router tweakings .... ) I tried to make it as compact as possible ( it can be more compact if made with more layers ) the matrix is driven by a I2C protocol driven by IS31FL3737
To build your own, just grab the gerber files, and send them to your preferred PCBA fab
Features :
- 12*12 led matrix
- 30 free GPIO by RP2040
- usb_c input
SCHEMATIC
PCB
3D preview
BOM
| # | Component | Supplier | Qty | Unit Price | Total (USD) |
|---|---|---|---|---|---|
| 1 | PCB | JLCPCB | 2 | $81 | $81 |
| TOTAL | $81 |
I hope you like this project
This project is sponsored by @JLCPCB
Parts
190| Qty | Value | Footprint | References |
|---|---|---|---|
| 144 | LED | LED_SMD:LED_0402_1005Metric | D1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112 +128 |
| 7 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C6, C7, C8, C9 |
| 4 | 0.47uF | Capacitor_SMD:C_0402_1005Metric | C21, C22, C23, C24 |
| 3 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C17, C19, C20 |
| 3 | 100k | Resistor_SMD:R_0402_1005Metric | R6, R7, R10 |
| 3 | 100n | Capacitor_SMD:C_0402_1005Metric | C11, C12, C14 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C10, C13 |
| 2 | 4.7k | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 20k | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 22uF | Capacitor_SMD:C_0402_1005Metric | C18 |
| 1 | Conn_01x03_Pin | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_Vertical_SMD_Pin1Left | J6 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical_SMD_Pin1Left | J5 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_1.00mm:PinHeader_1x06_P1.00mm_Vertical_SMD_Pin1Left | J4 |
| 1 | Conn_01x13_Pin | Connector_PinHeader_1.00mm:PinHeader_1x13_P1.00mm_Vertical_SMD_Pin1Left | J3 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | IS31FL3737 | Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.8x3.8mm | U4 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | Switch | Button_Switch_SMD:SW_SPST_SKQG_WithoutStem | SW1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |
Questions
How big is the Matrix PCB?
It measures 40 × 55 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Matrix use?
190 parts, built around the RP2040 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Matrix KiCad files?
From the Az154za/SGT_SCREEN repository on GitHub, at the commit this page was made from: the board is PCB/Matrix.kicad_pcb and its schematic PCB/Matrix.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Matrix design in my own project?
Its repository states no licence, so its author keeps all rights: ask Az154za before reusing the design.
Similar boards
- 2 layers181 × 97 mm
OpenDeck r3.1.2
shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.
262 parts960Apache-2.0 - 4 layers82.6 × 82.5 mm
- 4 layers102.9 × 96.7 mm
PicoGUS chipdown
polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support
99 parts805 - 4 layers180.8 × 300.3 mm
Dilemma
Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.
383 parts590 - 2 layers130.4 × 76.6 mm
Gb stream cart
Staacks/gbinterceptor
Capture or stream Game Boy gameplay footage via USB without modifying the Game Boy.
80 parts542 - 2 layers78 × 60 mm
- 2 layers44 × 44 mm
