Skip to the content
2 layers83 × 78.5 mmSuper dmg cpu, the printed circuit board in 3D

Super dmg cpu

awhit003/DMG-007

Super DMG JACK is a replacement headphone/audio PCB for the original Game Boy. It can be used on a stock DMG or the Super DMG-01.

Size
83 × 78.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
61
Nets
111
Pads
364
Tracks, vias
1,057, 289
Pours
7
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
4 Sep 2026
Updated
5 Sep 2026

Overview

Super dmg cpu is an open-source printed circuit board by awhit003, from the awhit003/DMG-007 repository on GitHub. It is a 2-layer board of 83 × 78.5 mm with 61 parts on 111 nets, routed with 1,057 tracks and 289 vias.

It is built around the LPW5209B5F-21 and BAV99-7-F-CN. Its parts include 21 capacitors, 11 resistors, 8 connectors, 5 ICs and 1 diode.

Main components

2

README

hardware/boards/02-super-dmg-jack/README.md

Super DMG JACK

Super DMG JACK is a replacement headphone/audio PCB for the original Game Boy. It can be used on a stock DMG or the Super DMG-01.

It uses a PAM8302 mono amplifier to power the speaker when no headphones are present, but it can also be built as a headphone jack replacement using the amplifier on the CPU board.

The amplifier schematic is based on Adafruit's pam8302 amplifier PCB.

The headphone output needs to be unamplified, and grabbed after the DMG volume potentiometer.

sdmg jack top sdmg jack bottom

sdmg jack sdmg jack full

BOM

DesignatorPackageQtyValue / DescriptionSource
CN1PJ-3043-B1Headphone connectorLCSC
CN21.25 TH1CPU PCB ConnectorLCSC
CN31.25 TH1Speaker ConnectorLCSC
U1SOP-81PAM8302LCSC
U2SOT-23-51SN74AHC1G14LCSC
VR1Bourns TC33X-2-103E110kΩ SMDLCSC
FB1, FB208052Ferrite Bead
C1, C2, C5080531µf
C3, C408053220pf
R1, R208052220Ω
R3, R408052100Ω
R50805110kΩ

I got premade wires from AliExpress (1.25mm 2p and 5p), but you can also just use 28/30 awg without connectors.

I use "WSC" 8Ω 2W speakers from AliExpress.

DMG Pinout

dmg-pinout

Full Installation

Important: do not solder U2 and/or do not wire the (E)nable signal. The speaker must be connected to this board.

  • Solder the SMD components
  • Solder the through hole components
  • On the stock DMG solder the L/R signals to the volume potentiometer (** after pot), on Super DMG-01 solder to the bottom pads directly
  • Get power from the 5v rail on the CPU board
  • Adjust the trimpot

Trimpot notes

Adjust the trimpot to reduce the power draw and max volume of the amplifier. Boot the DMG at minimum volume, and slowly turn it up, while also adjusting the trimpot. The Game Boy will shut down if you're drawing too much power. Do the final trimpot adjustment once the DMG volume is at its maximum value.

The final maximum volume will depend on the batteries and the voltage regulator you're using.

Jack-only Installation

The jack-only installation is meant to be used with the on-board DMG amplifier, however you still need to solder an extra wire for power as the ENABLE signal needs to be inverted.

Important: solder only U2, R5, the headphone jack and the CPU PCB connector. The speaker must be kept in the LCD board.

  • Solder the SMD components
  • Solder the through hole components
  • On the stock DMG solder the L/R signals to the volume potentiometer (** after pot), on Super DMG-01 solder to the bottom pads directly
  • Get power from 5V (Super DMG CPU) or SW (stock DMG) on the CPU board

Notes

3d print the jack spacer for correct alignment.

Ordering

pcbway pcbway

Make sure you order in 1.0mm thickness.

License

This work is licensed under the Creative Commons Attribution-ShareAlike 4.0 International License.

Parts

61
QtyValueFootprintReferences
4100pFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC16, C17, C18, C19
4220ΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3, R4
4BAV99-7-Fkmc_lib:SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BRDA1, DA2, DA3, DA4
3100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC10, C24, C25
310nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC12, C13, C14
347nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC7, C8, C9
3GND PADdmg_lib:DMG_GROUNDPADP2, P3, P4
2100µfCapacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-T_Pad1.50x2.35mm_HandSolderC1, C23
210µFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC5, C6
21µFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3, C4
227pFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC21, C22
25.1kΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR10, R11
2510ΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5, R6
110kΩdmg_lib:DMG_VOLUME_POTVR1
110kΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR9
1180kΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR7
11MΩResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR8
11N414Diode_SMD:D_SOD-123D2
14.194304 MHzdmg_lib:HC-49SX1
1AMPdmg_lib:DMG_AMPU4
1AUDIOkmc_lib:PAD_2.54_HYBRID_X5H3
1BATTERYdmg_lib:DMG_BATTERY_PADSCN3
1BATTERYeasyeda2kicad:CONN-TH_2P-P1.25_HCTL_HC-1.25-2AWCN4
1CARTdmg_lib:DMG_CART_CONNCN2
1CART SHIELD GND PADSdmg_lib:DMG_CART_SHIELD_CONTACTP1
1CHARGE_PORTkmc_lib:USB_C_16pUSB1
1CPUdmg_lib:DMG_CPUU1
1DMGB_CHRG_HEADERkmc_lib:PAD_2.54_HYBRID_X3H4
1DPDTkmc_lib:DMGB_POWER_SWITCHSW1
1EXTdmg_lib:DMG_LINK_CONNEXT1
1LOGOLOGOG***
1LPW5209B5F-21easyeda2kicad:SOT-23-5_L2.9-W1.6-P0.95-LS2.8-BLU5
1POWERkmc_lib:PAD_2.54_HYBRID_X6H2
1RAMdmg_lib:DMG_RAM_64KU3
1SCREENdmg_lib:DMG_FPC_CONNCN1
1VRAMdmg_lib:DMG_RAM_64KU2
1bypasskmc_lib:solder_jumper_x2JP5
1kmceda-glyphs:kmc_6mmG1

More from awhit003/DMG-007

2
  • 2 layers65 × 15 mmDMGC PWR-01 2-3, the printed circuit board in 3D

    DMGC PWR-01 2-3

    awhit003/DMG-007

    Super DMG JACK is a replacement headphone/audio PCB for the original Game Boy. It can be used on a stock DMG or the Super DMG-01.

    41 parts
  • 2 layers54.5 × 16 mmSuper dmg jack, the printed circuit board in 3D

    Super dmg jack

    awhit003/DMG-007

    Super DMG JACK is a replacement headphone/audio PCB for the original Game Boy. It can be used on a stock DMG or the Super DMG-01.

    23 parts

Similar boards

  • 2 layers100 × 160 mmPcb kicad, the printed circuit board in 3D

    Pcb kicad

    hmaerki/experiment_microoctopus

    Ideas on how to set up a micropython testenvironment

    67 parts2MIT
  • 4 layers87.1 × 78.2 mm3 in 1 Panel, the printed circuit board in 3D

    3 in 1 Panel

    kelu124/pic0rick

    An rp2040-based acquisition board for pulse-echo ultrasound

    115 parts116
  • 6 layers567.7 × 328.4 mmARX, the printed circuit board in 3D

    ARX

    lwa-project/analog_receiver

    Analog Receiver (ARX) Board

    2,771 parts1
  • 4 layers85 × 54 mmPICO ADC Test, the printed circuit board in 3D

    PICO ADC Test

    kelu124/oshmri

    OpenSourceHardware - going to MRI

    59 parts2
  • 4 layers117 × 60 mmCw lite main, the printed circuit board in 3D

    Cw lite main

    nikitalita/cw-kicad-conversions

    334 parts
  • 2 layers390 × 78.2 mmMBO, the printed circuit board in 3D

    MBO

    shanteacontrols/OpenDeck

    A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

    61 parts960Apache-2.0
  • 2 layersTUSS4470 shield, the printed circuit board in 3D

    TUSS4470 shield

    Neumi/open_echo

    Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.

    61 parts530
  • 2 layers45 × 45 mmAirCube, the printed circuit board in 3D

    AirCube

    StuckAtPrototype/AirCube

    Works standalone out of the box. Pairs with Home Assistant in minutes. Other platforms are supported through community-contributed extensions.

    61 parts379Apache-2.0

Questions

How big is the Super dmg cpu PCB?

It measures 83 × 78.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Super dmg cpu use?

61 parts, built around the LPW5209B5F-21 and BAV99-7-F-CN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Super dmg cpu KiCad files?

From the awhit003/DMG-007 repository on GitHub, at the commit this page was made from: the board is hardware/boards/01-super-dmg-cpu/super-dmg-cpu.kicad_pcb and its schematic hardware/boards/01-super-dmg-cpu/super-dmg-cpu.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Super dmg cpu design in my own project?

Its repository states no licence, so its author keeps all rights: ask awhit003 before reusing the design.