2 layers68 × 40 mm
Stm32-io extend
hardenedlinux/cheap-pcb
Cheap PCB: Better understanding the current status of hardware supply chain
44 parts170CC0-1.0
2 layers64 × 42.2 mm
Blackpill
avnguyen08/STM32PCB_Design- Size
- 64 × 42.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 47
- Pads
- 179
- Tracks, vias
- 341, 34
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Mar 2024
- Updated
- 15 Mar 2024
Overview
Blackpill is an open-source printed circuit board by avnguyen08, from the avnguyen08/STM32PCB_Design repository on GitHub. It is a 2-layer board of 64 × 42.2 mm with 35 parts on 47 nets, routed with 341 tracks and 34 vias.
It is built around the STM32F103C8T6 and AMS1117-3.3. Its parts include 13 capacitors, 7 resistors, 4 connectors, 2 ICs and 1 diode. It belongs with the STM32 boards of this library.
Main components
2
STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C5, C6, C7, C11 |
| 4 | 1k5 | Resistor_SMD:R_0402_1005Metric | R1, R3, R4, R5 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C9, C10 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R6, R7 |
| 2 | 6p | Capacitor_SMD:C_0402_1005Metric | C12, C13 |
| 2 | Conn_01x20 | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J3, J4 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | LOGO | LOGO | G*** |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | USB_C_2.0_Receptacle | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
Similar boards
- 2 layers99.1 × 58.4 mm
HEAT
milar111/HEAT
An open-source STM32 SMD assembly station for precision soldering. Uses a custom Smart Pulse & Coast algorithm to drive 400W mains heaters via SSR. Features OLED UI, NTC feedback, and safety cooling.
57 parts9 - 2 layers71.3 × 25.4 mm
- 2 layers78 × 60 mm
DC Motor Controller
minhle4397/Line-Follower-Robot-v2
Improved Hardware and Firmware for Line Follower Robot
53 parts3 - 4 layers36 × 36 mm
TrackMAG
mupfdev/TrackMAG
An open hardware development board primarily intended for the development of accessible input devices.
58 parts3 - 2 layers154.7 × 113 mm
DeskMixer
RaduAndre/DeskMixer
DeskMixer is a software that allows control of application volumes with real sliders, and action mapping on buttons using arduino like platforms. The project was inspired originally by deej.
113 parts3 - 2 layers42 × 33 mm
STM32 course
abda-s/STM32-Phill-s-Lab-PCB-Course
A beginner-friendly introduction to STM32 hardware design and KiCad
32 parts2 - 2 layers53.3 × 35.6 mm
Questions
How big is the Blackpill PCB?
It measures 64 × 42.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Blackpill use?
35 parts, built around the STM32F103C8T6 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Blackpill KiCad files?
From the avnguyen08/STM32PCB_Design repository on GitHub, at the commit this page was made from: the board is blackpill/blackpill.kicad_pcb and its schematic blackpill/blackpill.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Blackpill design in my own project?
Its repository states no licence, so its author keeps all rights: ask avnguyen08 before reusing the design.