

LegoLight
- Size
- 39.8 × 70.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 66
- Pads
- 269
- Tracks, vias
- 1,079, 70
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 13 Apr 2024
- Updated
- 12 May 2024
Overview
LegoLight is an open-source printed circuit board by averrin, from the averrin/LegoLight repository on GitHub. It is a 2-layer board of 39.8 × 70.2 mm with 59 parts on 66 nets, routed with 1,079 tracks and 70 vias.
It is built around the ATSAMD21E18A-AF, PCA9685PW and PCA9306D, with the EG1271, SK6812 and TL3305AF160QG among its other parts. Its parts include 16 resistors, 15 connectors, 5 diodes, 4 capacitors and 4 ICs. It belongs with the SAM D and SAM boards of this library.
Main components
7ATSAMD21E18A-AF
TQFP-32(7x7)-40℃~+125℃ 1.62V~3.6V 10bit 12bit 256KB 26 32 Bit 32KB 48MHz ARM Cortex-M0+ Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PCA9685PW
TSSOP-28-40℃~+85℃ 100kHz~1MHz 16 2.3V~5.5V 25mA 5.5V Built-in PWM TSSOP-28 LED Drivers ROHSNXP SemiconductorsLED DriversPCA9306D
SO-8-40℃~+105℃ 1 1.8V~5.5V 1V~3.6V 2 2Mbps Automatic direction detection、Output enable high-impedance Bidirectional Level translator Open-drain SMBus、I2C SO-8 Translators, Level Shifters ROHSNXP SemiconductorsTranslators, Level ShiftersEG1271
插件Slide SwitchesE-SwitchSK6812
SMD-4P,5.4x5mm-40℃~+85℃ 0.6mA 1.6mm 120° 160mcd~320mcd 1kHz 2000V 280mcd~515mcd 3.7V~5.5V 460nm~470nm 520nm~530nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Built-in power-on reset circuit Semi-transparent lens SMD-4P,5.4x5mm RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)TL3305AF160QG
SMD-4P,4.5x4.5mm-20℃~+70℃ 1.6N 12V 3.8mm 4.5mm 4.5mm 500,000 Cycles 50mA Black Gull Wing Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,4.5x4.5mm Tactile Switches ROHSE-SwitchTactile SwitchesUSB4105-GF-A
SMD-40℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 430OHM | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R4, R8, R14 |
| 4 | 4K7OHM | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6, R9, R10, R19 |
| 4 | MountingHole_2.5mm_Pad | MountingHole:MountingHole_2.5mm_Pad | MH1, MH2, MH3, MH4 |
| 3 | 10KOHM | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R11, R12, R13 |
| 3 | A1 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP3, JP4 |
| 3 | BLUE | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3, D4, D5 |
| 3 | MOMENTARY-SWITCH-SPST-SMD-4.6X2.8MM | SnapEDA Library:SW_TL3305AF160QG | PA11, PA14, PA15 |
| 2 | 0 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J12, J14 |
| 2 | 1.0UF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C6 |
| 2 | 10UF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C5 |
| 2 | 4k7ohm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2, R5 |
| 2 | 5.1KOHM | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R17, R18 |
| 2 | 5v | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J9, J25 |
| 2 | I2C | Connector:NS-Tech_Grove_1x04_P2mm_Vertical | J3, J7 |
| 2 | VCC | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J13, J15 |
| 1 | 0-7 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J24 |
| 1 | 200KOHM | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R7 |
| 1 | 24LC01BT-I_OT | SnapEDA Library:SOT95P280X145-5N | U1 |
| 1 | 8-15 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J8 |
| 1 | A0 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | AP2112K-3.3V | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | AP2112K-3.3V1 |
| 1 | ATSAMD21E18A-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U3 |
| 1 | C1 | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J5 |
| 1 | EG1271 | SnapEDA Library:SW_EG1271 | S5 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J16 |
| 1 | I2C_INT | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | LED_PORT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | ALED1 |
| 1 | PCA9306D | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | PCA9685PW | Package_SO:TSSOP-28_4.4x9.7mm_P0.65mm | U2 |
| 1 | RED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | SK6812 | LED_SMD:LED_SK6812_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 1 | SWD | Connector_PinSocket_1.27mm:PinSocket_2x05_P1.27mm_Vertical | J4 |
| 1 | TL3305AF160QG | SnapEDA Library:SW_TL3305AF160QG | RESETb1 |
| 1 | USB4105-GF-A | SnapEDA Library:GCT_USB4105-GF-A | J17 |
More from averrin/LegoLight
4- 2 layers30 × 65 mm

- 2 layers30 × 65 mm

- 2 layers30 × 65 mm

- 2 layers64.1 × 56 mm

Similar boards
- 4 layers44 × 44 mm

Boot console
clarkmcc/my-first-linux-board
my-first-linux-board is a small F1C200S Linux board built around removable microSD storage, USB-C power and USB device data, a 3.3 V UART console, and power/status LEDs.
93 parts1 - 2 layers141 × 90.9 mm

Haptic bracelet
earlynerd/ELRS-haptics
Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…
269 parts - 6 layers80 × 80 mm

- 2 layers111 × 60 mm

- 2 layers53 × 30 mm

Breadboard Power Supply
DeepSpace00/Breadboard-Power-Supply
Duel power supply for breadboard power rails
28 partsCERN-OHL-P-2.0 - 4 layers65 × 66 mm

Main V2
MCiuzelis/LituanicaX_AutonomousCarPlatform
Mechanical and electrical design files for the LituanicaX autonomous RC car: a Raspberry Pi 5–based robot that navigates a cone-track circuit using a depth camera.
69 parts - 4 layers100 × 100 mm

Pi TX 35W PA V2
M0LTE/pi-transceiver
An attempt to build a complete ham radio transceiver around a Raspberry Pi
185 parts15 - 2 layers130 × 120 mm

Questions
How big is the LegoLight PCB?
It measures 39.8 × 70.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LegoLight use?
59 parts, built around the ATSAMD21E18A-AF, PCA9685PW, PCA9306D and EG1271. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LegoLight KiCad files?
From the averrin/LegoLight repository on GitHub, at the commit this page was made from: the board is Hardware/LegoLight/LegoLight.kicad_pcb and its schematic Hardware/LegoLight/LegoLight.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LegoLight design in my own project?
Its repository states no licence, so its author keeps all rights: ask averrin before reusing the design.