4 layers85 × 57.5 mm
2 layers88.9 × 106.7 mm
DataLogger
ataweg/DataLoggerDataLogger using "Arduino UNO" board and Greiman SdFat library
- Size
- 88.9 × 106.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 62
- Nets
- 53
- Pads
- 217
- Tracks, vias
- 341, 32
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Nov 2021
- Updated
- 22 Nov 2021
Overview
DataLogger is an open-source printed circuit board by ataweg, from the ataweg/DataLogger repository on GitHub, published under the MIT licence. It is a 2-layer board of 88.9 × 106.7 mm with 62 parts on 53 nets, routed with 341 tracks and 32 vias.
It is built around the ATMEGA328P-PU, MAX3232ID and AMS1117, with the BAT42 and 100UF/16V among its other parts. Its parts include 18 resistors, 12 capacitors, 11 diodes, 7 connectors and 3 ICs. It belongs with the sensors and measurement boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
5
ATMEGA328P-PU
DIP-28-300mil-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH DIP-28-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MAX3232ID
SOIC-16-40℃~+85℃ 2 2 250Kbps 300uA 3V~5.5V Short-Circuit Protection Transceiver Yes ±15kV SOIC-16 RS232 ICs ROHSTexas InstrumentsRS232 ICs
AMS1117
1.0 A Low-Dropout Fixed RegulatorAdvanced Monolithic SystemsUncategorised
BAT42
DO-35-65℃~+125℃ 200mA 30V 4A 500nA@25V 650mV@50mA Independent DO-35 Schottky Diodes ROHSSTMicroelectronicsSchottky Diodes
100UF/16V
C1812C1812 SMT ROHSJLCPCB AssemblyUncategorised
README
README.mdDataLogger
DataLogger using "Arduino UNO" board and Greiman SdFat library
Parts
62| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitors_THT:C2_WIMA_2.5x6.5 | C102, C103, C108, C109, C110, C111, C112 |
| 5 | 470R | Resistors_THT:R4 | R103, R105, R109, R110, R111 |
| 4 | HOLE_32 | Mounting_Holes:HOLE_32 | M101, M102, M103, M104 |
| 4 | HOLE_43 | Mounting_Holes:HOLE_43 | M105, M106, M107, M108 |
| 4 | ZD15 | Diodes_THT:D3 | D104, D105, D106, D107 |
| 3 | 100R | Resistors_THT:R4 | R101, R102, R107 |
| 3 | 1K8 | Resistors_THT:R4 | R112, R113, R114 |
| 3 | 3K3 | Resistors_THT:R4 | R116, R117, R118 |
| 2 | 100nF | Capacitors_THT:C1_WIMA_3x7.5 | C106, C107 |
| 2 | 22pF | Capacitors_THT:C1D3_CER | C104, C105 |
| 2 | BAT42 | Diodes_THT:D3 | D108, D109 |
| 2 | LED yellow | LEDs:LED_3mm_yellow | D102, De |
| 1 | 100uF/16V | Capacitors_THT:CP1HR_6.3x11 | C101 |
| 1 | 10K | Resistors_THT:R4 | R104 |
| 1 | 16MHz | Crystals:HC-49SV | X101 |
| 1 | 1K8 | Resistors_THT:R4-5 | R115 |
| 1 | 1M | Resistors_THT:R4 | R106 |
| 1 | 1N4148 | Diodes_THT:D3 | D103 |
| 1 | 4k7 | Resistors_THT:R4 | R108 |
| 1 | AMS1117 | TO_SOT_Packages_SMD:SOT-223 | IC102 |
| 1 | ATmega328P-PU | Housings_DIP:Socket_DIP-28_W7.62mm | IC105 |
| 1 | AVR_SPI_PRG_6 | Pin_Headers:pinheader_2x3 | P104 |
| 1 | CONN_1x4 | Pin_Sockets:pinsocket_90_1x4 | P101 |
| 1 | CONN_2x10 | Pin_Headers:box_pinheader_90_2x10 | P103 |
| 1 | CONN_2x2 | Pin_Headers:pinheader_2x2 | P102 |
| 1 | LED green | LEDs:LED_3mm_green | D111 |
| 1 | LED red | LEDs:LED_3mm_red | D110 |
| 1 | MAX3232 | Housings_DIP:Socket_DIP-16_W7.62mm | IC101 |
| 1 | SD_Card | Components:SdCard_RSMT2MQ | J101 |
| 1 | SUBD-F09C-US | Connectors:DB9FC_US | J102 |
| 1 | SW_PHAP-3305 | Buttons_Switches_THT:PHAP-3305B-8.35mm | SW101 |
| 1 | SW_PUSH | Buttons_Switches_THT:DT6-grey | SW102 |
| 1 | USB_B_Micro | Modules:USB-Micro-Connector | J103 |
Similar boards
- 2 layers51.7 × 79.4 mm
Control motor dc
kr4fty/DCMotorController
Closed Loop Position Control for DC Servo Motors. STEP / DIR compatible Driver
26 parts5GPL-2.0 - 2 layers95.9 × 129.5 mm
Solderin Station
kr4fty/DiySolderingStation
Diy Soldering Stations with Atmega (Arduino UNO). Firmware and hardware design included
73 parts3GPL-2.0 - 2 layers100 × 90 mm
Entrenador atmega328p
davixcky/entrenador-atmega328p
Entrenador de microcontroladores con ATMega328P (DIP) - Sistemas Embebidos 1, actividad 10.1.12
75 parts - 2 layers100 × 100 mm
- 2 layers20.3 × 25.7 mm
ESP8266
agkaminski/ZAK181
Improved ZAK180: DIY all-in-keyboard computer featuring Z180 and floppy drive.
18 parts - 2 layers92 × 75 mm
Bit v4.1.0
alazifi/baby-incubator-tester
Berikut pasangan versi yang diimplementasikan untuk menghasilkan kinerja alat yang optimal.
57 parts - 2 layers50.9 × 36.5 mm
RobotArmMK1.2
EthanLawlor/RobotArm
6 Degree of Freedom Articulated Robot Arm. 3D Modelled and Printed, Servo Actuators, ATmege328P based custom PCB with BLE Communications, Custom Android APK for Controls.
25 partsGPL-3.0
Questions
How big is the DataLogger PCB?
It measures 88.9 × 106.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DataLogger use?
62 parts, built around the ATMEGA328P-PU, MAX3232ID, AMS1117 and BAT42. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DataLogger KiCad files?
From the ataweg/DataLogger repository on GitHub, at the commit this page was made from: the board is Board/DataLogger/DataLogger.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DataLogger design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).